TS925IPT ,RAIL TO RAIL HIGH OUTPUT CURRENT QUAD OPERATIONAL AMPLIFIERELECTRICAL CHARACTERISTICS+ -V = 3V, V = 0V, T = 25°C (unless otherwise specified) CC CC ambOPER ..
TS925IPT ,RAIL TO RAIL HIGH OUTPUT CURRENT QUAD OPERATIONAL AMPLIFIERAPPLICATIONS Input 1Input 4- + + -Non-invertingNon-inverting143Input 1Input 4■ Headphone amplifierV ..
TS931A ,OUTPUT RAIL TO RAIL MICROPOWER OPERATIONAL AMPLIFIERSTS931TS932TS934OUTPUT RAIL TO RAILMICROPOWER OPERATIONAL AMPLIFIERSn RAIL TO RAIL OUTPUT VOLTAGE SW ..
TS931AID ,OUTPUT RAIL TO RAIL MICROPOWER OPERATIONAL AMPLIFIERSTS931TS932TS934OUTPUT RAIL TO RAILMICROPOWER OPERATIONAL AMPLIFIERS ■ RAIL TO RAIL OUTPUT VOLTAGE ..
TS931AIDT ,OUTPUT RAIL TO RAIL MICROPOWER OPERATIONAL AMPLIFIERSTS931TS932TS934OUTPUT RAIL TO RAILMICROPOWER OPERATIONAL AMPLIFIERS ■ RAIL TO RAIL OUTPUT VOLTAGE ..
TS931AILT ,OUTPUT RAIL TO RAIL MICROPOWER OPERATIONAL AMPLIFIERSABSOLUTE MAXIMUM RATINGS Symbol Parameter Value Unit1)V12 VCC Supply voltage 2)V±12 Vid Differ ..
UAA3580 ,Wideband code division multiple access frequency division duplex zero IF receiver
UAA4000 ,Remote Control TransmitterBLOCK DIAGRAM
SUPPLY SWITCH
&
REGULATOR
SWITC H
MATRIX
CURRENT . det,
sounces
PULSE ..
UAA4006ADP , SWITCH MODE POWER SUPPLY CONTROL CIRCUIT
UAA4009 ,Remote Control Receiver£77
SGS-'r'HtNRSOH
jiiijl]CR(5)E[r/%7iiic(N%)2i)
UAA4009
REMOTE CONTROL RECEIVER
ON-CH ..
UAA4009 ,Remote Control ReceiverGENERAL DESCRIPTION
PPM DEMODULATION
The receiver operates on a timescale fixed by an in-
te ..
UAA4713DP ,MOTION DETECTOR INTERFACEapplications.The device can be usedprogrammable timer will start and switch a lampin a wide range o ..
TS925AID-TS925AIN-TS925ID-TS925IDT-TS925IN-TS925IPT
RAIL TO RAIL HIGH OUTPUT CURRENT QUAD OPERATIONAL AMPLIFIER
RAIL TO RAIL INPUT AND OUTPUT LOW NOISE : 9nV/√Hz LOW DISTORTION HIGH OUTPUT CURRENT : 80mA (able to drive 32Ω loads) HIGH SPEED : 4MHz, 1.3V/μs OPERATING FROM 2.7V TO 12V LOW INPUT OFFSET VOLTAGE : 900μV max. (TS925A)
ADJUSTABLE PHANTOM GROUND (VCC/2) STANDBY MODE ESD INTERNAL PROTECTION : 2kV LATCH-UP IMMUNITY
MACROMODEL INCLUDED IN THIS SPECIFICATION
DESCRIPTIONThe TS925 is a RAIL TO RAIL quad BiCMOS op-
erational amplifier optimized and fully specified for
3V and 5V operation.
High output current allows low load impedances to
be driven. An internal low impedance PHANTOM
GROUND eliminates the need for an external ref-
erence voltage or biasing arrangement.
The TS925 exhibits a very low noise, low distor-
tion and high output current making this device an
excellent choice for high quality, low voltage or
battery operated audio/telecom systems.
The device is stable for capacitive loads up to
500pF.
When the STANDBY mode is enabled, the total
consumption drops to 6μA (VCC = 3V).
APPLICATIONS Headphone amplifier Soundcard amplifier, piezoelectric speaker MPEG boards, multimedia systems, ... Cordless telephones and portable communi-
cation equipment Line driver, buffer Instrumentation with low noise as key factor
ORDER CODE
N = Dual in Line Package (DIP) D = Small Outline Package (SO) - also available in Tape & Reel (DT)
P = Thin Shrink Small Outline Package (TSSOP) - only available in Tape & Reel (PT)
PIN CONNECTIONS (top view)
TS925RAIL TO RAIL HIGH OUTPUT CURRENT
QUAD OPERATIONAL AMPLIFIER
TS925
ABSOLUTE MAXIMUM RATINGS
OPERATING CONDITIONS All voltage values, except differential voltage are with respect to network ground terminal. Differential voltages are the non-inverting input terminal with respect to the inverting input t erminal. The magnitude of input and output voltages must never exceed VCC + +0.3V. Short-circuits can cause excessive heating. Destructive dissipation can result from simultaneous short-circuit on all amplifiers.Do not short circuit outputs to VCC+ when exceeding 8V : this can induce reliability defects.
TS925
ELECTRICAL CHARACTERISTICSVCC+ = 3V, VCC- = 0V, Tamb = 25°C (unless otherwise specified)
OPERATIONAL AMPLIFIER
TS925
GLOBAL CIRCUIT
PHANTOM GROUND the STANDBY mode is currently enabled when Pin 9 is GROUNDED and disabled when Pin 9 is left OPEN. Cdec is the decoupling capacitor on Pin9
TS925
ELECTRICAL CHARACTERISTICSVCC+ = 5V, VCC- = 0V, Tamb = 25°C (unless otherwise specified)
TS925
GLOBAL CIRCUIT
PHANTOM GROUND the STANDBY mode is currently enabled when Pin 9 is GROUNDED and disabled when Pin 9 is left OPEN. Cdec is the decoupling capacitor on Pin9
TS925
INPUT OFFSET VOLTAGE DISTRIBUTION
SUPPLY CURRENT/AMPLIFIER vs
TEMPERATURE
OUTPUT SHORT CIRCUIT CURRENT vs
OUTPUT VOLTAGE
TOTAL SUPPLY CURRENT vsSUPPLY
VOLTAGE WITH NO LOAD
OUTPUT SHORT CIRCUIT CURRENT vs
OUTPUT VOLTAGE
OUTPUT SHORT CIRCUIT CURRENT vs
OUTPUT VOLTAGE
TS925
OUTPUT SHORT CIRCUIT CURRENT vs
TEMPERATURE
DISTORSION + NOISE vs FREQUENCY
THD + NOISE vs FREQUENCY
VOLTAGE GAIN AND PHASE vs FREQUENCY
THD + NOISE vs FREQUENCY
THD + NOISE vs FREQUENCY
