TS912BID ,INPUT/OUTPUT RAIL TO RAIL DUAL CMOS OP-AMPSELECTRICAL CHARACTERISTICS- +V = 3V, V = 0V, R , C connected to V , T = 25°C (unless otherwise spec ..
TS912BIDT ,RAIL TO RAIL CMOS CMOS OP-AMPELECTRICAL CHARACTERISTICS- +V = 5V, V = 0V, R , C connected to V , T = 25°C (unless otherwise spec ..
TS912BIYDT ,Low power with CMOS inputsAbsolute maximum ratingsSymbol Parameter Value Unit(1)V Supply voltage 18 VCC(2)V Differential inpu ..
TS912I ,RAIL TO RAIL CMOS DUAL OPERATIONAL AMPLIFIERTS912 RAIL TO RAILCMOS DUAL OPERATIONAL AMPLIFIER.RAIL TO RAIL INPUT AND OUTPUTVOLTAGERANGES.SINGL ..
TS912ID ,RAIL TO RAIL CMOS CMOS OP-AMPTS912RAIL TO RAILCMOS DUAL OPERATIONAL AMPLIFIER ■ RAIL TO RAIL INPUT AND OUTPUT VOLT-AGE RAN ..
TS912IDT ,RAIL TO RAIL CMOS CMOS OP-AMPELECTRICAL CHARACTERISTICS- +V = 3V, V = 0V, R , C connected to V , T = 25°C (unless otherwise spec ..
UAA3535 ,Low power GSM/DCS/PCS multi-band transceiver
UAA3535 ,Low power GSM/DCS/PCS multi-band transceiver
UAA3540TS ,DECT receiver
UAA3580 ,Wideband code division multiple access frequency division duplex zero IF receiver
UAA4000 ,Remote Control TransmitterBLOCK DIAGRAM
SUPPLY SWITCH
&
REGULATOR
SWITC H
MATRIX
CURRENT . det,
sounces
PULSE ..
UAA4006ADP , SWITCH MODE POWER SUPPLY CONTROL CIRCUIT
TS912BID-TS912BIDT
RAIL TO RAIL CMOS CMOS OP-AMP
RAIL TO RAIL INPUT AND OUTPUT VOLT-AGE RANGES SINGLE (OR DUAL) SUPPLY OPERATION
FROM 2.7V TO 16V EXTREMELY LOW INPUT BIAS CURRENT :
1pA typ LOW INPUT OFFSET VOLTAGE : 2mV max. SPECIFIED FOR 600Ω AND 100Ω LOADS LOW SUPPLY CURRENT : 200μA/Ampli
(VCC = 3V) LATCH-UP IMMUNITY ESD TOLERANCE : 3KV
SPICE MACROMODEL INCLUDED IN THIS-SPECIFICATION
DESCRIPTIONThe TS912 is a RAIL TO RAIL CMOS dual opera-
tional amplifier designed to operate with a single
or dual supply voltage.
The input voltage range Vicm includes the two sup-
ply rails VCC+ and VCC-.
At 3V, the output reaches : VCC- +30mV VCC+ -40mV with RL = 10kΩ VCC- +300mVVCC+ -400mV with RL = 600Ω
This product offers a broad supply voltage operat-
ing range from 2.7V to 16V and a supply current of
only 200μA/amp @ VCC = 3V.
Source and sink output current capability is typi-
cally 40mA at VCC = 3V, fixed by an internal limita-
tion circuit.
ORDER CODE
N = Dual in Line Package (DIP) D = Small Outline Package (SO) - also available in Tape & Reel (DT)
PIN CONNECTIONS (top view)
TS912
RAIL TO RAILCMOS DUAL OPERATIONAL AMPLIFIER
TS912
SCHEMATIC DIAGRAM (1/2 TS912)
ABSOLUTE MAXIMUM RATINGS
OPERATING CONDITIONS All voltages values, except differential voltage are with respect to network ground terminal. Differential voltagesare non-inverting input terminal with respect to the inverting input terminal. The magnitude of input and output voltages must never exceed VCC+ +0.3V.
TS912
ELECTRICAL CHARACTERISTICSVCC+ = 3V, Vcc
- = 0V, RL, CL connected to VCC/2, Tamb = 25°C (unless otherwise specified) Maximum values including unavoidable inaccuracies of the industrial test
TS912
ELECTRICAL CHARACTERISTICSVCC+ = 5V, Vcc
- = 0V, RL, CL connected to VCC/2, Tamb = 25°C (unless otherwise specified) Maximum values including unavoidable inaccuracies of the industrial test
TS912
ELECTRICAL CHARACTERISTICSVCC+ = 10V, Vcc
- = 0V, RL, CL connected to VCC/2, Tamb = 25°C (unless otherwise specified) Maximum values including unavoidable inaccuracies of the industrial test
TS912
TYPICAL CHARACTERISTICS
Figure 1 : Supply Current (each amplifier)
vs Supply Voltage
Figure 3a : High Level Output Voltage vs High
Level Output Current
Figure 4a : Low Level Output Voltage vs Low
Level Output Current
Figure 2 : Input Bias Current vs Temperature
Figure 3b : High Level Output Voltage vs High
Level Output Current
Figure 4b : Low Level Output Voltage vs Low
Level Output Current
