TS904IN ,INPUT/OUTPUT RAIL TO RAIL QUAD CMOS OP-AMPSTS904®RAIL TO RAIL CMOS QUADOPERATIONAL AMPLIFIER (WITH STANDBY POSITION).RAIL TO RAIL INPUT AND OU ..
TS912AI ,RAIL TO RAIL CMOS DUAL OPERATIONAL AMPLIFIERELECTRICAL CHARACTERISTICS+ - oV =5V,V =0V,R ,C connected to V /2, T =25 C (unless otherwise specif ..
TS912AID ,RAIL TO RAIL CMOS CMOS OP-AMPABSOLUTE MAXIMUM RATINGS Symbol Parameter Value Unit1)V18 VCC Supply voltage 2)V±18 Vid Differ ..
TS912AIDT ,RAIL TO RAIL CMOS CMOS OP-AMPELECTRICAL CHARACTERISTICS- +V = 5V, V = 0V, R , C connected to V , T = 25°C (unless otherwise spec ..
TS912AIN ,RAIL TO RAIL CMOS CMOS OP-AMPELECTRICAL CHARACTERISTICS- +V = 5V, V = 0V, R , C connected to V , T = 25°C (unless otherwise spec ..
TS912AIYDT ,Low power with CMOS inputsFeatures■ Rail-to-rail input and output voltage ranges■ Single (or dual) supply operation from 2.7 ..
UAA3535 ,Low power GSM/DCS/PCS multi-band transceiver
UAA3535 ,Low power GSM/DCS/PCS multi-band transceiver
UAA3540TS ,DECT receiver
UAA3580 ,Wideband code division multiple access frequency division duplex zero IF receiver
UAA4000 ,Remote Control TransmitterBLOCK DIAGRAM
SUPPLY SWITCH
&
REGULATOR
SWITC H
MATRIX
CURRENT . det,
sounces
PULSE ..
UAA4006ADP , SWITCH MODE POWER SUPPLY CONTROL CIRCUIT
TS904AID-TS904ID-TS904IN
INPUT/OUTPUT RAIL TO RAIL QUAD CMOS OP-AMPS
TS904
RAIL TO RAIL CMOS QUADOPERATIONAL AMPLIFIER (WITH ST
ANDBY POSITION)April 1999
RAIL TO RAIL INPUT AND OUTPUTVOLTAGE RANGES. 2 SEPARATE STANDBY : REDUCED
CONSUMPTION (0.5μA) AND HIGH IMPED-
ANCE OUTPUTS. SINGLE (OR DUAL) SUPPLY OPERATION
FROM 2.7V TO 16V. EXTREMELY LOW INPUT BIAS CURRENT :
1pA TYP. LOW INPUT OFFSET VOLTAGE : 5mV max.. SPECIFIED FOR 600Ω AND 150Ω LOADS. LOW SUPPLY CURRENT : 200μA/Ampli.
SPICE MACROMODEL INCLUDED IN THISSPECIFICATION
PIN CONNECTIONS (top view)
DESCRIPTIONThe TS904 is a RAIL TO RAIL quad CMOS opera-
tional amplifier designed to operate with a single or
dual supply voltage.
The input voltage range Vicm includes the two
supply rails VCC+ and VCC-.
The output reaches : VCC- +50mV VCC+ -50mV with RL = 10kΩ VCC- +350mV VCC+ -350mV with RL = 600Ω
This product offers a broad supply voltage operat-
ing range from 2.7V to 16V and a supply current of
only 200μA/amp. (VCC = 3V)
Source and sink output current capability is typi-
cally 40mA (at VCC = 3V), fixed by an internal
limitation circuit.
The TS904 offers two separate STANDBY pins STANDBY 1 acting on the n°2 and
n°3 operators STANDBY 2 acting on the n°1 and
n°4 operators
They reduce the consumption of the corresponding
operators and put the outputs in a high impedance
state.
These two STANDBY pins should never stay not
connected.
STMicroelectronics is offering a quad op-amp with
the same features : TS902.
ORDER CODES1/12
ABSOLUTE MAXIMUM RATINGS
SCHEMATIC DIAGRAM (1/4 TS904)
STANDBY POSITION
OPERATING CONDITIONS
TS9042/12
ELECTRICAL CHARACTERISTICSVCC+ = 3V, VCC- = 0V, RL,CL connected to VCC/2, pin 8 and pin 9 connected to VCC+
, Tamb = 25oC
(unless otherwise specified)
Note 1 : Maximum values including unavoidable inaccuracies of the industrial test.
TS9043/12
ELECTRICAL CHARACTERISTICSVCC+ = 5V, VCC- = 0V, RL,CL connected to VCC/2 ,pin 8 and pin 9 connected to VCC+ , Tamb = 25oC
(unless otherwise specified)
Note 1 : Maximum values including unavoidable inaccuracies of the industrial test.
TS9044/12
ELECTRICAL CHARACTERISTICSVCC+ = 10V, VCC- = 0V, RL,CL connected to VCC/2, pin 8 and 9 connected to VCC+ , Tamb = 25oC
(unless otherwise specified)
Note 1 : Maximum values including unavoidable inaccuracies of the industrial test.
STANDBY MODEVCC+ = 10V, VCC- = 0V, Tamb = 25o C (unless otherwise specified)
TS9045/12
TYPICAL CHARACTERISTICS (standby OFF = standby 1 and 2 OFF)
(standby ON = standby 1 and 2 ON)SUPPLY VOLTAGE, V (V)
0 4 8 12 16
SUPPLY CURRENT, I ( A)
Figure 1a : Supply Current (each amplifier)
versus Supply Voltage
25 50 75 100 125
INPUT BIAS CURRENT, I (pA)
ambTEMPERATURE, T ( C)°
Figure 2 : Input Bias Current versus Temperature
14 28 42 56 70
OUTPUT VOLTAGE, V (V) OUTPUT CURRENT, I (mA)
Figure 4a : Low Level Output Voltage versus
Low Level Output Current
-70 -56 -42 -28 -14 0
OUTPUT VOLTAGE, V (V) OUTPUT CURRENT, I (mA)
Figure 3a : High Level Output Voltage versus
High Level Output Current
OUTPUT VOLTAGE, V (V) OUTPUT CURRENT, I (mA)
-70 -56 -42 -28 -14 0
Figure 3b : High Level Output Voltage versus
High Level Output Current
4 8 12 16SUPPLY VOLTAGE, V (V)
SUPPLY CURRENT, I ( A)
Figure 1b : Supply Current (each amplifier)
versus Supply Voltage (in STANDBY
mode)
TS9046/12
