TS4890IQT ,1W MONO AUDIO AMPLIFIER WITH STANDBY ACTIVE HIGHELECTRICAL CHARACTERISTICSV = +5V, GND = 0V, T = 25°C (unless otherwise specified) CC ambSymbol ..
TS4890IST ,RAIL TO RAIL OUTPUT 1W AUDIO POWER AMPLIFIER WITH STANDBY MODETS4890RAIL TO RAIL OUTPUT 1W AUDIO POWER AMPLIFIER WITHSTANDBY MODE ACTIVE LOW ■ OPERATING FROM V ..
TS4900 ,300MW AT 3.3V SUPPLY AUDIO POWER AMPLIFIER WITH STANDBY MODE ACTIVE HIGHELECTRICAL CHARACTERISTICSV = +5V, GND = 0V, T = 25°C (unless otherwise specified) CC ambSymbol ..
TS4900ID ,300MW AT 3.3V SUPPLY AUDIO POWER AMPLIFIER WITH STANDBY MODE ACTIVE HIGHTS4900 300mW at 3.3V SUPPLY AUDIO POWER AMPLIFIERWITH STANDBY MODE ACTIVE HIGH ■ OPERATING FROM V ..
TS4902ID ,300MW AT 3.3V SUPPLY AUDIO POWER AMPLIFIER WITH STANDBY MODE ACTIVE LOWABSOLUTE MAXIMUM RATINGS Symbol Parameter Value Unit1)V6VCC Supply voltage 2)V G to VVi Input ..
TS4902IDT ,300MW AT 3.3V SUPPLY AUDIO POWER AMPLIFIER WITH STANDBY MODE ACTIVE LOWELECTRICAL CHARACTERISTICSV = +5V, GND = 0V, T = 25°C (unless otherwise specified) CC ambSymbol ..
UA709 ,HIGH-PERFORMANCE OPERATIONAL AMPLIFIERapplications and for the generation of special
linear and nonlinear transfer functions.
ABSOLUT ..
UA709HC ,HIGH-PERFORMANCE OPERATIONAL AMPLIFIERfeatures low offset, high input impedance,
large input common mode range, high output swing under ..
UA709HM ,HIGH-PERFORMANCE OPERATIONAL AMPLIFIERGENERAL DESCRIPTION - The pA709 is a monolithic High Gain Operational Amplifier con-
structed usin ..
UA709PC ,HIGH-PERFORMANCE OPERATIONAL AMPLIFIERELECTRICAL CHARACTERISTICS: TA " +25''C, 19 V < VS < t15 V unless otherwise specified.
CHARACTER ..
UA709TC ,High-performance operational amplifierapplications and for the generation of special
linear and nonlinear transfer functions.
ABSOLUT ..
UA709TC ,High-performance operational amplifierELECTRICAL CHARACTERISTICS: TA " +25''C, 19 V < VS < t15 V unless otherwise specified.
CHARACTER ..
TS4890IQT
1W MONO AUDIO AMPLIFIER WITH STANDBY ACTIVE HIGH
1/32 OPERATING FROM VCC = 2.2V to 5.5V
1W RAI L TO RAIL OUTPUT POWER @ Vcc=5V, THD=1%, f=1kHz, with 8Ω Load ULTRA LOW CONSUMPTION IN STANDBY
MODE (10nA)
75dB PSRR @ 217Hz from 5 to 2.2V POP & CLICK REDUCTION CIRCUITRY ULTRA LOW DISTORTION (0.1%) UNITY GAIN STABLE AVAILABLE IN SO8, MiniSO8 & DFN8
DESCRIPTIONThe TS4890 (MiniSO8 & SO8) is an Audio Power
Amplifier capable of delivering 1W of continuous
RMS. ouput power into 8Ω load @ 5V.
This Audio Amplifier is exhibiting 0.1% distortion
level (THD) from a 5V supply for a Pout = 250mW
RMS. An external standby mode control reduces
the supply current to less than 10nA. An internal
thermal shutdown protection is also provided.
The TS4890 have been designed for high quality
audio applications such as mobile phones and to
minimize the number of external components.
The unity-gain stable amplifier can be configured
by external gain setting resistors.
APPLICATIONS Mobile Phones (Cellular / Cordless) Laptop / Notebook Computers PDAs Portable Audio Devices
ORDER CODE MiniSO & DFN only available in Tape & Reel: with T suffix.
SO is available in Tube (D) and of Tape & Reel (DT)
PIN CONNECTIONS (Top View)
TS4890RAIL TO RAIL OUTPUT 1W AUDIO POWER AMPLIFIER WITH
STANDBY MODE ACTIVE LOW
June 2003
TS48902/32
ABSOLUTE MAXIMUM RATINGS
OPERATING CONDITIONS All voltages values are measured with respect to the ground pin. The magnitude of input signal must never exceed VCC + 0.3V / GND - 0.3V Device is protected in case of over temperature by a thermal shutdown active @ 150°C. Exceeding the power derating curves during a long period may involve abnormal working of the device. This thermal resistance can be reduced with a suitable PCB layout (see Power Derating Curves Fig. 24) When mounted on a 4 layers PCB
TS48903/32
ELECTRICAL CHARACTERISTICSVCC = +5V, GND = 0V, Tamb = 25°C (unless otherwise specified)
VCC = +3.3V, GND = 0V, Tamb = 25°C (unless otherwise specified) Standby mode is actived when Vstdby is tied to GND Dynamic measurements - 20*log(rms(Vout)/rms(Vripple)). Vripple is the surimposed sinus signal to Vcc @ f = 217Hz Standby mode is actived when Vstdby is tied to GND Dynamic measurements - 20*log(rms(Vout)/rms(Vripple)). Vripple is the surimposed sinus signal to Vcc @ f = 217Hz
TS48904/32
VCC = 2.6V, GND = 0V, Tamb = 25°C (unless otherwise specified)
VCC = 2.2V, GND = 0V, Tamb = 25°C (unless otherwise specified) Standby mode is actived when Vstdby is tied to GND Dynamic measurements - 20*log(rms(Vout)/rms(Vripple)). Vripple is the surimposed sinus signal to Vcc @ f = 217Hz Standby mode is actived when Vstdby is tied to GND Dynamic measurements - 20*log(rms(Vout)/rms(Vripple)). Vripple is the surimposed sinus signal to Vcc @ f = 217Hz
TS48905/32
REMARKS
1. All measurements, except PSRR measurements, are made with a supply bypass capacitor Cs = 100μF.
1. External resistors are not needed for having better stability when supply @ Vcc down to 3V. The quiescent current still remains the same.
2. The standby response time is about 1μs.