TS3V3704IDT ,3V MICROPOWER QUAD CMOS VOLTAGE COMPARATORELECTRICAL CHARACTERISTICS+ -V = 3V, V = 0V, T = 25°C (unless otherwise specified) CC CC ambSymb ..
TS3V3704IN ,3V MICROPOWER QUAD CMOS VOLTAGE COMPARATORABSOLUTE MAXIMUM RATINGS Symbol Parameter Value Unit+1)18 VV Supply Voltage CC2)V ±18 VDiffere ..
TS3V393I ,3V MICROPOWER DUAL VOLTAGE COMPARATORSTS3V3933V MICROPOWER DUAL VOLTAGE COMPARATORS.DEDICATED TO 3.3V OR BATTERY SUPPLY(specified at 3V a ..
TS3V393ID ,3V MICROPOWER DUAL CMOS VOLTAGE COMPARATORTS3V393C,I,M3V MICROPOWER DUAL CMOS VOLTAGE COMPARATORS ■ DEDICATED TO 3.3V OR BATTERY SUPPLY ..
TS3V555I ,3V LOW POWER SINGLE TIMERSELECTRICAL CHARACTERISTICSoVCC = +3V , Tamb = +25 C , Reset to VCC (unless otherwise specified)STAT ..
TS3V555ID ,3V LOW POWER SINGLE CMOS TIMERBLOCK DIAGRAMResetVCC8 43V555RR1Q Output3+Threshold 6RControl-5 AVoltageSR+-Trigger 2BRDischarge71G ..
U891BS , Prescaler for TV and VTR purposes
U9120 ,Advanced Power MOSFETFEATURESBV = -100 VDSSn Avalanche Rugged TechnologyR = 0.6 ΩDS(on) n Rugged Gate Oxide Tech ..
UA2-3NU ,Super-compact size, Slim-package, Surface mounting typeFEATURES™ Small mounting size of slim package for dense mounting.™ Bellcore (2500 V) and FCC (1500 ..
UA709 ,HIGH-PERFORMANCE OPERATIONAL AMPLIFIERapplications and for the generation of special
linear and nonlinear transfer functions.
ABSOLUT ..
UA709HC ,HIGH-PERFORMANCE OPERATIONAL AMPLIFIERfeatures low offset, high input impedance,
large input common mode range, high output swing under ..
UA709HM ,HIGH-PERFORMANCE OPERATIONAL AMPLIFIERGENERAL DESCRIPTION - The pA709 is a monolithic High Gain Operational Amplifier con-
structed usin ..
TS3V3704ID-TS3V3704IDT-TS3V3704IN
3V MICROPOWER QUAD CMOS VOLTAGE COMPARATOR
DEDICATED TO 3.3V OR BATTERY SUPPLY(specified at 3V and 5V) PUSH-PULL CMOS OUTPUT (NO EXTER-
NAL PULL-UP RESISTOR REQUIRED) EXTREMELY LOW SUPPLY CURRENT :
7μA typ / comparator WIDE SINGLE SUPPLY RANGE
2.7V to 16V EXTREMELY LOW INPUT OFFSET
CURRENTS : 1pA typ INPUT COMMON-MODE VOLTAGE RANGE
INCLUDES GND FAST RESPONSE TIME : 2μs typ for 5mV
overdrive PIN-TO-PIN AND FUNCTIONALLY
COMPATIBLE WITH BIPOLAR LM339
DESCRIPTION The TS3V3704 is a micropower quad CMOS volt-
age comparator with extremely low consumption
of 7μA typ / comparator (20 times less than bipolar
LM339). The push-pull CMOS output stage allows
power and space saving by eliminating the exter-
nal pull-up resistor required by usual open-collec-
tor output comparators.
Thus response times remain similar to the LM339.
ORDER CODE
N = Dual in Line Package (DIP)
D = Small Outline Package (SO) - also available in Tape & Reel (DT)
P = Thin Shrink Small Outline Package (TSSOP) - only available in Tape & Reel (PT)
PIN CONNECTIONS (top view)
TS3V3704
3V MICROPOWER QUAD CMOS VOLTAGE COMPARATORSTS3V3704
SCHEMATIC DIAGRAM (for 1/4 TS3V3704)
ABSOLUTE MAXIMUM RATINGS
OPERATING CONDITIONS All voltage values, except differential voltage, are with respect to network ground terminal. Differential voltages are the non-inverting input terminal with respect to the inverting input terminal. The magnitude of the input and the output voltages must never exceed the magnitude of the possitive supply voltage. Guaranteed by design. Pd is calculated with Tamb = +25°C, Tj = +150°C and Rthja = 80°C/W for DIP14 package= 150°C/W for SO14 package= 175°C/W for TSSOP14 package
TS3V3704
ELECTRICAL CHARACTERISTICSVCC+ = 3V, VCC- = 0V, Tamb = 25°C (unless otherwise specified) The specified offset voltage is the maximun value required to drive the output up to 4.5V or down to 0.3V. Maximum values including unavoidable inaccuracies of the industrial test.
TS3V3704
ELECTRICAL CHARACTERISTICSVCC+ = 5V, VCC- = 0V, Tamb = 25°C (unless otherwise specified) The specified offset voltage is the maximun value required to drive the output up to 4.5V or down to 0.3V. Maximum values including unavoidable inaccuracies of the industrial test.
TS3V3704
PACKAGE MECHANICAL DATA14 PINS - PLASTIC DIP
TS3V3704
PACKAGE MECHANICAL DATA14 PINS - PLASTIC MICROPACKAGE (SO)
Note : (1) D and F do not include mold flash or protrusions - Mold flash or protrusions shall not exceed 0.15mm (.066 inc) ONLY FOR DATA BOOK.
