TS393IDT ,MICROPOWER DUAL CMOS VOLTAGE COMPARATORABSOLUTE MAXIMUM RATINGS Symbol Parameter Value Unit+1)18 VV Supply Voltage CC2)V ±18 VDiffere ..
TS393IPT ,MICROPOWER DUAL CMOS VOLTAGE COMPARATORTS393C,I,MMICROPOWER DUAL CMOS VOLTAGE COMPARATORS ■ EXTREMELY LOW SUPPLY CURRENT : 9μA typ / ..
TS393MD ,MICROPOWER DUAL CMOS VOLTAGE COMPARATORABSOLUTE MAXIMUM RATINGS Symbol Parameter Value Unit+1)18 VV Supply Voltage CC2)V ±18 VDiffere ..
TS3A24157DGSR ,0.65 Ohm Dual SPDT Analog Switch Dual-Channel 2:1 Multiplexer/Demultiplexer 10-VSSOP -40 to 85 SCDS208B–JUNE 2007–REVISED OCTOBER 20165 Pin Configuration and FunctionsDGS Package RSE Package10- ..
TS3A24157RSER ,0.65 Ohm Dual SPDT Analog Switch Dual-Channel 2:1 Multiplexer/Demultiplexer 10-UQFN -40 to 85Block Diagram... 14Information..... 194 Revision HistoryNOTE: Page numbers for previous revisions m ..
TS3A24159DRCR ,0.3-Ohm 2-Channel SPDT Bidirection Switch 10-VSON -40 to 85Features 3 DescriptionThe TS3A24159 is a 2-channel single-pole double-1• Specified Break-Before-Mak ..
U74LVC1G17G-AL5-R , SINGLE SCHMITT-TRIGGER BUFFER
U8060B , TELEFUNK ELECTRONIC CREATIVE TECHNOLOGIEN U2200B-FP
U813BS , 1.1-GHz Prescaler for PLLs in TV, CATV and SAT TV Tuners
U833BS , 1.3-GHz Prescaler for PLLs in TV, CATV and SAT TV Tuners
U842B , Wiper Control for Intermittent and Wipe/ Wash Mode
U842B , Wiper Control for Intermittent and Wipe/ Wash Mode
TS393CD-TS393CDT-TS393CN-TS393IDT-TS393IPT-TS393MD
MICROPOWER DUAL CMOS VOLTAGE COMPARATOR
EXTREMELY LOW SUPPLY CURRENT :
9μA typ / comparator WIDE SINGLE SUPPLY RANGE
2.7V TO 16V OR DUAL SUPPLIES(±1.35V TO ±8V) EXTREMELY LOW INPUT BIAS CURRENT :
1pA typ EXTREMELY LOW INPUT OFFSET
CURRENTS : 1pA typ INPUT COMMON-MODE VOLTAGE RANGE
INCLUDES GND HIGH INPUT IMPEDANCE : 1012 Ω typ FAST RESPONSE TIME : 2.5μs typ for
5mV overdrive PIN-TO-PIN AND FUNCTIONALLY
COMPATIBLE WITH BIPOLAR LM393
DESCRIPTION The TS393 is a micropower CMOS dual voltage
comparator with extremely low consumption of
9μA typ / comparator (20 times less than bipolar
LM393). Similar performances are offered by the
dual micropower comparator TS3702 with a
push-pull CMOS output.
Thus response times remain similar to the LM393.
ORDER CODE
N = Dual in Line Package (DIP)
D = Small Outline Package (SO) - also available in Tape & Reel (DT)
P = Thin Shrink Small Outline Package (TSSOP) - only available in Tape & Reel (PT)
PIN CONNECTIONS (top view)
TS393C,I,MMICROPOWER DUAL CMOS VOLTAGE COMPARATORS
TS393C,I,M
SCHEMATIC DIAGRAM (for 1/2 TS393)
ABSOLUTE MAXIMUM RATINGS
OPERATING CONDITIONS All voltage values, except differential voltage, are with respect to network ground terminal. Differential voltages are the non-inverting input terminal with respect to the inverting input terminal. Excursions of input voltages may exceed the power supply level. As long as the common mode voltage [Vicm=(Vin+ + Vin- )/2] remains
within the specified range, the comparator will provide a stable output state. However, the maximum current through the ESD diodes (if)
of the input stage must strictly be observed. The output must never exceed the power supply voltage. Guaranteed by design. Pd is calculated with Tamb = +25°C, Tj = +150°C and Rthja = 100°C/W for DIP8 package= 175°C/W for SO8 package
= 200°C/W for TSSOP8 package
TS393C,I,M
ELECTRICAL CHARACTERISTICSVCC+ = 3V, Vcc- = 0V, Tamb = 25°C (unless otherwise specified) The specified offset voltage is the maximun value required to drive the output up to 2.5V or down to 0.3V. Maximum values including unavoidable inaccuracies of the industrial test.
TS393C,I,M
ELECTRICAL CHARACTERISTICSVCC+ = 5V, Vcc- = 0V, Tamb = 25°C (unless otherwise specified) The specified offset voltage is the maximun value required to drive the output up to 4.5V or down to 0.3V. Maximum values including unavoidable inaccuracies of the industrial test.
TS393C,I,M
PACKAGE MECHANICAL DATA8 PINS - PLASTIC DIP
TS393C,I,M
PACKAGE MECHANICAL DATA8 PINS - PLASTIC MICROPACKAGE (SO)
