TRS3223EIDWR ,3-V to 5.5-V Multichannel RS-232 Line Driver/Receiver With +/-15-kV IEC ESD Protection 20-SOIC -40 to 85maximum ratings" may cause permanent damage to the device. These are stress ratingsonly, and functi ..
TRS3223EIPW ,3-V to 5.5-V Multichannel RS-232 Line Driver/Receiver With +/-15-kV IEC ESD Protection 20-TSSOP -40 to 85Maximum Ratingsover operating free-air temperature range (unless otherwise noted)MIN MAX UNITV Supp ..
TRS3223EIPWR ,3-V to 5.5-V Multichannel RS-232 Line Driver/Receiver With +/-15-kV IEC ESD Protection 20-TSSOP -40 to 85LOGIC DIAGRAM (POSITIVE LOGIC)13 17DIN1 DOUT112 8DIN2DOUT220FORCEOFF 11Powerdown INVALID14FORCEON1E ..
TRS3227ECDB ,3-V to 5.5-V Single-Channel RS-232 Line Driver/Receiver With +/-15-kV ESD Protection 16-SSOP 0 to 70FEATURES APPLICATIONS• Battery-Powered, Hand-Held, and Portable• Meets or Exceeds the Requirements ..
TRS3227EIDB ,3-V to 5.5-V Single-Channel RS-232 Line Driver/Receiver With +/-15-kV ESD Protection 16-SSOP -40 to 85SLLS795–JUNE 2007TERMINAL FUNCTIONSTERMINALDESCRIPTIONNAME NO.C1+ 2 Positive terminal of voltage-do ..
TRS3227IDB ,3-V to 5.5-V Single-Channel RS-232 Line Driver/Receiver With +/-15-kV ESD Protection 16-SSOP -40 to 85FEATURES APPLICATIONS• Battery-Powered, Hand-Held, and Portable• Meets or Exceeds the Requirements ..
U2270B ,Read/write base station ICFeatures• Carrier Frequency f 100 kHz - 150 kHzosc Typical Data Rate up to 5 kbaud at 125 kHz Sui ..
U2320B , VHF/UHF Tuner-IC
U2320B , VHF/UHF Tuner-IC
U237BG ,To drive LED-displays with 5 or 10 diodesBlock diagram LED scale IC Et,T1,2/181th0386 E1 i'_ ... . _ ." _ mug! _. . '30 36 ' ty-o 9 g" , 227 ..
U2391B , Quartz Controlled Pulse Generator
U2391B , Quartz Controlled Pulse Generator
TRS3223ECDB-TRS3223ECDW-TRS3223ECPW-TRS3223EIDB-TRS3223EIDWR-TRS3223EIPW-TRS3223EIPWR
3-V to 5.5-V Multichannel RS-232 Line Driver/Receiver With +/-15-kV IEC ESD Protection 20-SOIC 0 to 70
TRS3223E 3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER WITH ±15-kV ESD PROTECTION www.ti.com SLLS794–JUNE 2007 FEATURES DB, DW, OR PW PACKAGE • ESD Protection for RS-232 Bus Pins (TOP VIEW) – ±15-kV Human-Body Model (HBM) EN 1 20 FORCEOFF – ±8-kV IEC61000-4-2, Contact Discharge C1+ 2 19 V CC – ±15-kV IEC61000-4-2, Air-Gap Discharge V+ 3 18 GND • Meets or Exceeds the Requirements of C1− 4 17 DOUT1 TIA/EIA-232-F and ITU v.28 Standards C2+ 5 16 RIN1 • Operates With 3-V to 5.5-V V Supply C2− 6 15 ROUT1 CC 7 14 V− FORCEON • Operates up to 500 kbit/s 8 13 DOUT2 DIN1 • Two Drivers and Two Receivers 9 12 RIN2 DIN2 • Low Standby Current . . . 1 μA Typ 10 11 ROUT2 INVALID • External Capacitors . . . 4 × 0.1 μF • Accepts 5-V Logic Input With 3.3-V Supply RHL PACKAGE • Alternative High-Speed Pin-Compatible Device (TOP VIEW) (1 Mbit/s) for TRSF3223E APPLICATIONS • Battery-Powered Systems • PDAs 1 24 • Notebooks C1+ V • Laptops 2 23 CC N.C. N.C. 3 22 • Palmtop PCs V+ 4 21 GND • Hand-Held Equipment C1– 5 20 DOUT1 C2+ 6 19 RIN1 DESCRIPTION/ C2– 7 18 ROUT1 ORDERING INFORMATION V– 8 17 FORCEON The TRS3223E consists of two line drivers, two line 9 16 DOUT2 DIN1 receivers, and a dual charge-pump circuit with 10 15 N.C. N.C. ±15-kV ESD protection pin to pin (serial-port 11 14 RIN2 DIN2 connection pins, including GND). The device meets 12 13 the requirements of TIA/EIA-232-F and provides the electrical interface between an asynchronous communication controller and the serial-port connector. The charge pump and four small external capacitors allow operation from a single 3-V to 5.5-V N.C. − No internal connection supply. The device operates at typical data signaling rates up to 500 kbit/s and a maximum of 30-V/μs driver output slew rate. Flexible control options for power management are available when the serial port is inactive. The auto-powerdown feature functions when FORCEON is low and FORCEOFF is high. During this mode of operation, if the device does not sense a valid RS-232 signal, the driver outputs are disabled. If FORCEOFF is set low and EN is high, both drivers and receivers are shut off, and the supply current is reduced to 1 mA. Disconnecting the serial port or turning off the peripheral drivers causes auto-powerdown to occur. Auto-powerdown can be disabled when FORCEON and FORCEOFF are high. With auto-powerdown enabled, the device is activated automatically when a valid signal is applied to any receiver input. The INVALID output is used to notify the user if an RS-232 signal is present at any receiver input. INVALID is high (valid data) if any receiver input voltage is greater than 2.7 V or less than –2.7 V, or has been between –0.3 V and 0.3 V for less than 30 μs. INVALID is low (invalid data) if the receiver input voltage is between –0.3 V and 0.3 V for more than 30 μs. Refer to Figure 4 for receiver input levels. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. UNLESS OTHERWISE NOTED this document contains Copyright © 2007, PRODUCTION DATA information current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. ROUT2 EN INVALID FORCEOFF