TPIC6595DW ,8-Bit Shift Registermaximum ratings over recommended operating case temperature range (unless†otherwise noted)Logic sup ..
TPIC6595N ,8-Bit Shift Registermaximum ratings” may cause permanent damage to the device. These are stress ratings only andfunctio ..
TPIC6596N ,8-Bit Shift Register SLIS096A − APRIL 2000 − REVISED MAY 2005DW OR N PACKAGE Low r . ..
TPIC6A259DW ,8-Bit Addressable Latchfeatures an independentPGND 5 20 PGNDchopping current-limiting circuit to preventPGND PGND6 19damag ..
TPIC6A595DW ,8-Bit Shift Registerfeatures an independent 3 22G Vchopping current-limiting circuit to prevent 4 21CCPGND PGNDdamage i ..
TPIC6A595NE ,8-Bit Shift Registermaximum ratings over recommended operating case temperature range (unless†otherwise noted)Logic sup ..
TS3USB3000RSER ,DPDT USB 2.0 High-Speed and Mobile High-Definition Link (MHL) (6.1GHz) Switch 10-UQFN -40 to 85Features:isolation of the signal lines under such conditionwithout excessive leakage current. The s ..
TS3USB30EDGSR ,High-Speed USB 2.0 1:2 Mux/Demux Switch With Single Enable and ESD Protection 10-VSSOP -40 to 85Electrical Characteristics. 612.2 Community Resources...... 176.7 Switching Characteristics...... 6 ..
TS3USB30ERSWR ,High-Speed USB 2.0 1:2 Mux/Demux Switch With Single Enable and ESD Protection 10-UQFN -40 to 85Features 3 DescriptionThe TS3USB30E is a high-bandwidth 1:2 switch1• V Operation at 3 V to 4.3 VCCs ..
TS3USB30RSWR ,High-Speed USB 2.0 (480 Mbps) 1:2 Multiplexer/Demultiplexer Switch With Single Enable 10-UQFN -40 to 85Features 3 DescriptionThe TS3USB30 is a high-bandwidth switch specially1• V Operation at 3 V and 4. ..
TS3USB31RSER ,High-Speed USB 2.0 (480-Mbps) 1-Port Switch With Single Enable 8-UQFN -40 to 85Features 3 DescriptionThe TS3USB31 is a 1:1 SPST high-bandwidth switch1• V Operation at 3 V and 4.3 ..
TS3USB3200RSVR ,USB 2.0 High-Speed and Mobile High-Definition Link Switch w/ ID Select and Flexible Power Control 16-UQFN -40 to 85Featurescontrol. These configurations allow the systemdesigner to use a common USB or Mico-USB– Fle ..
TPIC6595-TPIC6595DW-TPIC6595N
8-Bit Shift Register
1.5-A Pulsed Current Per Output Output Clamp Voltage at 45 V Devices Are Cascadable Low Power Consumption
descriptionThe TPIC6595 is a monolithic, high-voltage, high-
current power 8-bit shift register designed for use
in systems that require relatively high load power.
The device contains a built-in voltage clamp on
the outputs for inductive transient protection.
Power driver applications include relays, sole-
noids, and other medium-current or high-voltage
loads.
This device contains an 8-bit serial-in, parallel-out
shift register that feeds an 8-bit D-type storage
register. Data transfers through both the shift and
storage registers on the rising edge of the
shift-register clock (SRCK) and the register clock
(RCK) respectively. The storage register transfers
data to the output buffer when shift-
register clear (SRCLR) is high. When SRCLR is
low, the input shift register is cleared. When output
enable (G) is held high, all data in the output
buffers is held low and all drain outputs are off.
When G is held low, data from the storage register
is transparent to the output buffers. The serial
output (SER OUT) allows for cascading of the
data from the shift register to additional devices.
Outputs are low-side, open-drain DMOS
transistors with output ratings of 45 V and 250-mA
continuous sink current capability. When data in the output buffers is low, the DMOS-transistor outputs are off.
When data is high, the DMOS-transistor outputs have sink current capability.
Separate power and logic level ground pins are provided to facilitate maximum system flexibility. Pins 1, 10, 11,
and 20 are internally connected, and each pin must be externally connected to the power system ground in order
to minimize parasitic inductance. A single-point connection between pin 19, logic ground (LGND), and pins 1,
10, 11, and 20, power grounds (PGND), must be externally made in a manner that reduces crosstalk between
the logic and load circuits.
The TPIC6595 is characterized for operation over the operating case temperature range of −40°C to 125°C.
†This symbol is in accordance with ANSI/IEEE Std 91-1984
and IEC Publication 617-12.
SER IN
DRAIN0
DRAIN1
DRAIN2
DRAIN3
SRCLR
PGND
SER OUT
DRAIN7
DRAIN6
DRAIN5
DRAIN4
SRCK
RCK
PGND
logic symbol†
RCK
SRCLR
SRCK
SER IN
DRAIN0
DRAIN1
DRAIN2
DRAIN3
DRAIN4
DRAIN5
DRAIN6
DRAIN7
SER OUT
