TLC7135CDWR ,4.5-Bits, 0.003 kSPS ADC, Muxed BCD Output, True Differential Input, 1 Ch. SLAS074D − DECEMBER 1986 − REVISED S ..
TLC7135CDWRG4 ,4.5-Bits, 0.003 kSPS ADC, Muxed BCD Output, True Differential Input, 1 Ch. 28-SOIC BLOCK DIAGRAMDIGITAL SECTION2320POLARITYD1 (LSD)PolarityLatch19From AnalogFlip-FlopD2DigitSection18 ..
TLC7135CN ,4.5-Bits, 0.003 kSPS ADC, Muxed BCD Output, True Differential Input, 1 Ch.maximum ratings” may cause permanent damage to the device. These are stress ratings only, andfuncti ..
TLC7225CDW ,8-Bit, 5 us Quad DAC, Parallel Input, Simultaneous Update, Binary Input Codingmaximum ratings over operating free-air temperature range (unless otherwise note)Supply voltage ran ..
TLC7225CDWR ,8-Bit, 5 us Quad DAC, Parallel Input, Simultaneous Update, Binary Input Codingmaximum ratings over operating free-air temperature range (unless otherwise note)Supply voltage ran ..
TLC7225CDWRG4 ,8-Bit, 5 us Quad DAC, Parallel Input, Simultaneous Update, Binary Input Coding 24-SOIC 0 to 70block diagram5REFA_2Input DAC8 DAC OUTALatch Latch+AA A4REFB_1Input DACDAC OUTB8Latch Latch +B89–16 ..
TMP47P242VN , CMOS 4-bit Microcontroller
TMP47P242VN , CMOS 4-bit Microcontroller
TMP47P422VF , CMOS 4-BIT MICROCONTROLLER
TMP47P422VF , CMOS 4-BIT MICROCONTROLLER
TMP47P422VFG , TLCS-47 Series
TMP47P422VUG , TLCS-47 Series
TLC7135CDW-TLC7135CDWG4-TLC7135CDWR-TLC7135CDWRG4-TLC7135CN
4.5-Bits, 0.003 kSPS ADC, Muxed BCD Output, True Differential Input, 1 Ch.
True Differential Input Multiplexed Binary-Coded-Decimal (BCD)Output Low Rollover Error: ± 1 Count Max Control Signals Allow Interfacing With
UARTs or Microprocessors Autoranging Capability With Over-and
Under-Range Signals TTL-Compatible Outputs Second Source to Teledyne TSC7135,
Intersil ICL7135, Maxim ICL7135, and
Siliconix Si7135 CMOS Technology
DESCRIPTIONThe ICL7135C and TLC7135C converters are manufactured with Texas Instruments highly efficient CMOS
technology. These 4 1/2-digit, dual-slope-integrating, analog-to-digital converters (ADCs) are designed to
provide interfaces to both a microprocessor and a visual display. The digit-drive outputs D1 through D4 and
multiplexed binary-coded-decimal outputs B1, B2, B4, and B8 provide an interface for LED or LCD
decoder/drivers as well as microprocessors.
The ICL7135C and TLC7135C offer 50-ppm (one part in 20,000) resolution with a maximum linearity error of
one count. The zero error is less than 10 µV and zero drift is less than 0.5 µV/°C. Source-impedance errors are
minimized by low input current (less than 10 pA). Rollover error is limited to ±1 count.
The BUSY, STROBE, RUN/HOLD, OVER RANGE, and UNDER RANGE control signals support
microprocessor-based measurement systems. The control signals also can support remote data acquisition
systems with data transfer through universal asynchronous receiver transmitters (UARTs).
The ICL7135C and TLC7135C are characterized for operation from 0°C to 70°C.
AVAILABLE OPTIONSCaution. These devices have limited built-in protection. The leads should be shorted together or the device placed in conductive foam
during storage or handlilng to prevent electrostatic damage to the MOS gates.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
