TLC1514ID ,10-Bit, 400 kSPS ADC Serial Out, SPI/DSP Compatible I/F, Power Down, 4 Ch. TLC1514, TLC1518 5-V, 10-BIT, 400 KSPS, 4/8 CHANNEL, LOW POWER,SERIAL ANALOG-TO-DIGITAL CONVERTERS ..
TLC1518IDW ,10-Bit, 400 kSPS ADC Serial Out, SPI/DSP Compatible I/F, Power Down, 8 Ch. TLC1514, TLC1518 5-V, 10-BIT, 400 KSPS, 4/8 CHANNEL, LOW POWER,SERIAL ANALOG-TO-DIGITAL CONVERTERS ..
TLC1541 ,10-Bit, 32 kSPS ADC Serial Out, uProcessor Periph./Standalone, 11 Ch.block diagramREF+ REF–14 13110-Bit2Sample andSwitched-Capacitors3HoldAnalog-to-Digital4Converter561 ..
TLC1541CDW ,10-Bit, 32 kSPS ADC Serial Out, uProcessor Periph./Standalone, 11 Ch.maximum ratings over operating free-air temperature range (unless otherwise noted)Supply voltage, V ..
TLC1541IDWR ,10-Bit, 32 kSPS ADC Serial Out, uProcessor Periph./Standalone, 11 Ch. TLC1541 10-BIT ANALOG-TO-DIGITAL CONVERTERWITH SERIAL CONTROL AND 11 INPUTSSLAS073C – DECEMBER 199 ..
TLC1541IN ,10-Bit, 32 kSPS ADC Serial Out, uProcessor Periph./Standalone, 11 Ch. TLC1541 10-BIT ANALOG-TO-DIGITAL CONVERTERWITH SERIAL CONTROL AND 11 INPUTSSLAS073C – DECEMBER 199 ..
TMG16CQ60 , TRIAC(Through Hole/Non-isolated)
TMG25C60L , TRIAC(Through Hole/Non-isolated)
TMG25CQ60J , Full wave AC control applications.
TMG3C60D , TRIAC(Surface Mount Device/Non-isolated)
TMG3CQ60D , TRIAC(Surface Mount Device/Non-isolated)
TMG40C60L , designed for full wave AC control applications
TLC1514ID
10-Bit, 400 kSPS ADC Serial Out, SPI/DSP Compatible I/F, Power Down, 4 Ch.
Signal-to-Noise and Distortion Ratio:59 dB, fi = 12 kHz Spurious Free Dynamic Range: 72 dB,
fi = 12 kHz SPI/DSP-Compatible Serial Interfaces With
SCLK up to 20 MHz Single Supply 5 Vdc
External Ref, 6 mA at 5.5 V, Internal Ref) Power Down: Software/Hardware
Power-Down Mode (1 m A Max, Ext Ref),
Auto Power-Down Mode (5 m A, Ext Ref) Programmable Auto-Channel Sweep Pin Compatible, 12-Bit Upgrades Available
(TLC2554, TLC2558) SDO
SDI
SCLK
EOC/(INT)
VCC
REFP
REFM
PWDN
GND
CSTART
DW OR PW PACKAGESDO
SDI
SCLK
EOC/(INT)
VCC
REFP
REFM
PWDN
GND
CSTART
D OR PW PACKAGE
(TOP VIEW)(TOP VIEW)
descriptionThe TLC1518 and TLC1514 are a family of high-performance, 10-bit, low power, 1.4 m s, CMOS SAR
analog-to-digital converters (ADC) which operate from a single 5 V power supply. These devices have three
digital inputs and a 3-state output [chip select (CS), serial input-output clock (SCLK), serial data input (SDI), and
serial data output (SDO)] that provide a direct 4-wire interface to the serial port of most popular host
microprocessors (SPI interface). When interfaced with a DSP , a frame sync (FS) signal is used to indicate the
start of a serial data frame.
In addition to a high-speed A/D converter and versatile control capability, these devices have an on-chip analog
multiplexer that can select any analog inputs or one of three internal self-test voltages. The sample-and-hold
function is automatically started after the fourth SCLK edge (normal sampling) or can be controlled by a special
pin, CSTART , to extend the sampling period (extended sampling). The normal sampling period can also be
programmed as short (12 SCLKs) or as long (24 SCLKs) to accommodate faster SCLK operation popular
among high-performance signal processors. The TLC1518 and TLC1514 are designed to operate with very low
power consumption. The power-saving feature is further enhanced with software/hardware/auto power down
modes and programmable conversion speeds. The converter uses the external SCLK as the source of the
conversion clock. There is a 4-V internal reference available and an optional external reference can also be used
to achieve maximum flexibility.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
