TDA8569Q ,4 x 40 W BTL quad car radio power amplifierGENERAL DESCRIPTION• Diagnostic facility (distortion, short-circuit andtemperature pre-warning)The ..
TDA8571J ,4 x 40 W BTL quad car radio power amplifierGENERAL DESCRIPTION• Requires very few external components The TDA8571J is a integrated class-B out ..
TDA8579 ,Dual common-mode rejection differential line receiver
TDA8579 ,Dual common-mode rejection differential line receiver
TDA8579 ,Dual common-mode rejection differential line receiver
TDA8594SD ,I虏C-bus controlled 4 x 50 W power amplifierFeatures and benefits2.1 General2 2 Operates in legacy mode (non I C-bus) and I C-bus mode (3.3 V ..
TIP107TU ,PNP Epitaxial Silicon Darlington TransistorTIP105/106/107TIP105/106/107Monolithic Construction With Built In Base-Emitter Shunt Resistors • Hi ..
TIP110 ,PLASTIC MEDIUM-POWER COMPLEMENTARY SILICON TRANSISTORSTIP110/112TIP115/117®COMPLEMENTARY SILICON POWER DARLINGTON TRANSISTORS■ STMicroelectronics PREFERR ..
TIP110. ,PLASTIC MEDIUM-POWER COMPLEMENTARY SILICON TRANSISTORSPANASONIC INDL/ELEK CHD LEE I) " 5333652 DULUHB‘] B -[li?iylingtqt?Si Iicon NPN 'Power TransistorsT ..
TIP110G , Plastic Medium-Power Complementary Silicon Transistors
TIP111 ,PLASTIC MEDIUM-POWER COMPLEMENTARY SILICON TRANSISTORSOrder this document**by TIP110/DSEMICONDUCTOR TECHNICAL DATA !** *"*#**!**$ * * !** *. . . designe ..
TIP111TU ,NPN Epitaxial Silicon Darlington TransistorTIP110/111/112TIP110/111/112Monolithic Construction With Built In Base-Emitter Shunt Resistors• Com ..
TDA8569Q
4 x 40 W BTL quad car radio power amplifier
Philips Semiconductors Product specification×
40 W BTL quad car radio
power amplifier TDA8569Q
FEATURES Capable of driving 2 Ω loads Requires very few external components High output power Low output offset voltage Fixed gain Diagnostic facility (distortion, short-circuit and
temperature pre-warning) Good ripple rejection Mode select switch (operating, mute and standby) Load dump protection Short-circuit safe to ground, to VP and across the load Low power dissipation in any short-circuit condition Thermally protected Reverse polarity safe Electrostatic discharge protection No switch-on/switch-off plop Flexible leads Low thermal resistance Pin compatible with the TDA8567Q.
GENERAL DESCRIPTIONThe TDA8569Qisan integrated class-B output amplifierin
a 23-lead Single-In-Line (SIL) plastic power package. contains four amplifiers in Bridge-Tied Load (BTL)
configuration, each witha gainof26 dB. The output power
is 4×40 W in a 2 Ω load.
APPLICATIONS The device is developed primarily for car radio
applications.
QUICK REFERENCE DATA
ORDERING INFORMATION
Philips Semiconductors Product specification× 40 W BTL quad car radio
power amplifier TDA8569Q
BLOCK DIAGRAM
Philips Semiconductors Product specification× 40 W BTL quad car radio
power amplifier TDA8569Q
PINNING
Philips Semiconductors Product specification× 40 W BTL quad car radio
power amplifier TDA8569Q
FUNCTIONAL DESCRIPTIONThe TDA8569Q contains four identical amplifiers which
can be used for bridge applications. The gain of each
amplifier is fixed at 26 dB.
Mode select switch (pin MODE) Standby: low supply current (<100 μA) Mute: input signal suppressed Operating: normal on condition.
Since this pin hasa low input current (<80 μA),a low cost
supply switch can be applied. avoid switch-onplops,itis advisedto keepthe amplifier
in the mute mode during ≥150 ms (charging of the input
capacitors at pins IN1, IN2, IN3 and IN4).
This can be realized by: Microprocessor control External timing circuit (see Fig.3).
Diagnostic output (pin VDIAG)DYNAMIC DISTORTION DETECTOR (DDD)
At the onset of clipping of one or more output stages, the
dynamic distortion detector becomes active and pin VDIAG
goes LOW. This information canbe usedto drivea sound
processor or DC volume control to attenuate the input
signal and so limit the distortion. The output level of
pin VDIAG is independent of the number of channels that
are clipping (see Fig.4).
SHORT-CIRCUIT DIAGNOSTIC
When a short-circuit occurs at one or more outputs to
ground or to the supply voltage, the output stages are
switched off until the short-circuit is removed and the
deviceis switchedon again, witha delayof approximately ms after removal of the short-circuit. During this
short-circuit condition, pin VDIAG is continuously LOW.
Whena short-circuit occurs across the loadof oneor more
channels, the output stages are switched off for
approximately 10 ms. After that time it is checked during
approximately50μsto determine whether the short-circuit
is still present. Due to this duty cycle of 50 μs/10 ms the
average current consumption during this short-circuit
condition is very low.
During this short-circuit condition, pin VDIAG is LOW for ms and HIGH for 50 μs (see Fig.5). The protection
circuits of all channels are coupled. This means that if a
short-circuit condition occurs in
one of the channels,allchannels are switched off. Consequently, the power
dissipation in any short-circuit condition is very low.
TEMPERATURE PRE-WARNING
When the virtual junction temperatureTvj reaches 145 °C,
pin VDIAG goes LOW.
OPEN COLLECTOR OUTPUTS
The diagnostic pin has an open-collector output, so more
devices canbe tied together.An external pull-up resistoris
needed.
Philips Semiconductors Product specification× 40 W BTL quad car radio
power amplifier TDA8569Q
Philips Semiconductors Product specification× 40 W BTL quad car radio
power amplifier TDA8569Q
LIMITING VALUESIn accordance with the Absolute Maximum Rating System (IEC 60134).
THERMAL CHARACTERISTICS
Philips Semiconductors Product specification× 40 W BTL quad car radio
power amplifier TDA8569Q
CHARACTERISTICS= 14.4 V; Tamb =25 °C; measured in Fig.7; unless otherwise specified.
Notes The circuit is DC adjusted at VP=6to18 V and AC operating at VP= 8.5to18V. At VP=18to30 V the DC output voltage≤1 ⁄2VP.
Philips Semiconductors Product specification× 40 W BTL quad car radio
power amplifier TDA8569Q
CHARACTERISTICS= 14.4 V; RL =2 Ω; f=1 kHz; Tamb =25 °C; measured in the circuit of Fig.7; unless otherwise specified.
Notes Dynamic Distortion Detector (DDD) active, pin VDIAG is set to logic0. Frequency response externally fixed. Vripple =Vripple(max)=2V (p-p); Rs =0Ω. B=20 Hzto20 kHz; Rs =0Ω. B=20 Hzto20 kHz; Rs =10kΩ. B=20 Hzto20 kHz; independent of Rs. Po=25 W; Rs =10kΩ. Vi =Vi(max)=1V (RMS).
