IC Phoenix
 
Home ›  TT27 > TDA8560Q,2 x 40 W/2 Ohm stereo BTL car radio power amplifier with diagnostic facility
TDA8560Q Fast Delivery,Good Price
Part Number:
If you need More Quantity or Better Price,Welcom Any inquiry.
We available via phone +865332716050 Email
Partno Mfg Dc Qty AvailableDescript
TDA8560QPHN/a5avai2 x 40 W/2 Ohm stereo BTL car radio power amplifier with diagnostic facility


TDA8560Q ,2 x 40 W/2 Ohm stereo BTL car radio power amplifier with diagnostic facilityBLOCK DIAGRAMV VP1 P23 101mute switchCinput 1 mTDA8560Q4VAoutput 1A365ΩPROTECTIONS18 kΩLoad dumppow ..
TDA8561Q ,2 x 24 W BTL or 4 x 12 W single-ended car radio power amplifierBLOCK DIAGRAMV VP1 P2513non-inverting1mute switchCminput 160TDA8561QkΩ6VAoutput 12kΩ18 kΩpower stag ..
TDA8562Q ,4 x 12 W single-ended car radio power amplifier with dynamic distortion detector and diagnostic interface
TDA8562Q ,4 x 12 W single-ended car radio power amplifier with dynamic distortion detector and diagnostic interface
TDA8562Q ,4 x 12 W single-ended car radio power amplifier with dynamic distortion detector and diagnostic interface
TDA8563AQ ,2 x 40 W/2 ohm stereo BTL car radio power amplifier with diagnostic facilityBLOCK DIAGRAMV VP1 P2handbook, full pagewidth 3 101mute switchCinput 1 mTDA8563AQ4VAoutput 1A2.3kΩP ..
TIP100 ,Power Darlingtons for Linear and Switching Applications
TIP101 ,Power Darlingtons for Linear and Switching ApplicationsELECTRICAL CHARACTERISTICS (T = 25C unless otherwise noted)CCharacteristic Symbol Min Max UnitOFF ..
TIP102 ,Power Darlingtons for Linear and Switching ApplicationsTIP102TIP105 TIP107®COMPLEMENTARY SILICON POWER DARLINGTON TRANSISTORS■ STMicroelectronics PREFERRE ..
TIP102.. ,Power Darlingtons for Linear and Switching ApplicationsTIP102TIP105 TIP107®COMPLEMENTARY SILICON POWER DARLINGTON TRANSISTORS■ STMicroelectronics PREFERRE ..
TIP102G , Plastic Medium−Power Complementary Silicon Transistors
TIP105 ,Power Darlingtons for Linear and Switching Applications


TDA8560Q
2 x 40 W/2 Ohm stereo BTL car radio power amplifier with diagnostic facility

Philips Semiconductors Product specification
2 × 40 W/2 Ω stereo BTL car radio
power amplifier with diagnostic facility TDA8560Q
FEATURES
Requires very few external components High output power4 Ω and 2 Ω load impedance Low output offset voltage Fixed gain Diagnostic facility (distortion, short-circuit and
temperature detection) Good ripple rejection Mode select switch (operating, mute and standby) Load dump protection Short-circuit safe to ground, to VP and across the load Low power dissipation in any short-circuit condition Thermally protected Reverse polarity safe Electrostatic discharge protection No switch-on/switch-off plop Flexible leads Low thermal resistance.
GENERAL DESCRIPTION

The TDA8560Q is an integrated class-B output amplifier in
a 13-lead single-in-line (SIL) power package.
It contains 2×40 W/2 Ω amplifiers in BTL configuration.
The device is primarily developed for car radio
applications.
QUICK REFERENCE DATA
ORDERING INFORMATION
Philips Semiconductors Product specification
2 × 40 W/2 Ω stereo BTL car radio
power amplifier with diagnostic facility TDA8560Q
BLOCK DIAGRAM
Philips Semiconductors Product specification
2 × 40 W/2 Ω stereo BTL car radio
power amplifier with diagnostic facility TDA8560Q
PINNING
FUNCTIONAL DESCRIPTION

The TDA8560Q contains two identical amplifiers and can
be used for bridge applications. The gain of each amplifier
is fixed at 40 dB. Special features of the device are as
follows.
Mode select switch (pin 11)
Standby: low supply current (<100 μA) Mute: input signal suppressed Operating: normal on condition.
Since this pin has a very low input current (<40 μA), a low
cost supply switch can be applied.
To avoid switch-on plops, it is advised to keep the amplifier
in the mute mode during ≥100 ms (charging of the input
capacitors at pin 1 and pin 13).
This can be achieved by: Microprocessor control External timing circuit (see Fig.7).
Diagnostic output (pin 12)

DYNAMIC DISTORTION DETECTOR (DDD)
At the onset of clipping of one or more output stages, the
dynamic distortion detector becomes active and pin12
goes low. This information can be used to drive a sound
processor or DC volume control to attenuate the input
signal and thus limit the distortion. The output level of
pin 12 is independent of the number of channels that are
clipping (see Fig.3).
Philips Semiconductors Product specification
2 × 40 W/2 Ω stereo BTL car radio
power amplifier with diagnostic facility TDA8560Q
SHORT-CIRCUIT PROTECTION
When a short-circuit occurs at one or more outputs to
ground or to the supply voltage, the output stages are
switched off until the short-circuit is removed and the
device is switched on again, with a delay of approximately ms, after removal of the short-circuit. During this
short-circuit condition, pin 12 is continuously low.
When a short-circuit across the load of one or both
channels occurs the output stages are switched off during
approximately 20 ms. After that time it is checked during
approximately 50 μs to see whether the short-circuit is still
present. Due to this duty cycle of 50 μs/20 ms the average
current consumption during this short-circuit condition is
very low (approximately 40 mA).
During this short-circuit condition, pin 12 is low for 20 ms
and high for 50 μs (see Fig.4).
The power dissipation in any short-circuit condition is
very low.
TEMPERATURE DETECTION
When the virtual junction temperature Tvj reaches 150 °C,
pin 12 will become continuously low.
OPEN COLLECTOR OUTPUT
Pin 12 is an open collector output, which allows pin 12 of
more devices being tied together.
Philips Semiconductors Product specification
2 × 40 W/2 Ω stereo BTL car radio
power amplifier with diagnostic facility TDA8560Q
LIMITING VALUES

In accordance with the Absolute Maximum Rating System (IEC 134).
THERMAL CHARACTERISTICS
Philips Semiconductors Product specification
2 × 40 W/2 Ω stereo BTL car radio
power amplifier with diagnostic facility TDA8560Q
DC CHARACTERISTICS
= 14.4 V; Tamb =25 °C; measured in Fig.6; unless otherwise specified.
Notes
The circuit is DC adjusted at VP=6to18 V and AC operating at VP= 8.5to18V. At 18VPhilips Semiconductors Product specification
2 × 40 W/2 Ω stereo BTL car radio
power amplifier with diagnostic facility TDA8560Q
AC CHARACTERISTICS
= 14.4 V; RL =2 Ω; f=1 kHz; Tamb =25 °C; measured in Fig.6; unless otherwise specified.
Notes
Dynamic distortion detector active. Frequency response externally fixed. Vripple =Vripple(max)=2 V (p-p); Rs =0Ω. B=20Hzto20 kHz; Rs =0Ω. B=20Hzto20 kHz; Rs =10kΩ. B=20Hzto20 kHz; independent of Rs. Po=25 W; Rs =10kΩ. Vi =Vi(max)=1 V (RMS).
ic,good price


TEL:86-533-2716050      FAX:86-533-2716790
   

©2020 IC PHOENIX CO.,LIMITED