TDA5670-5X ,Video modulator for FM/AM audio with PLL-output Video Modulator for TDA 5670-5XFM/AM-Audio withPLL-OutputPreliminary Data Bipolar IC
TDA5670-5X ,Video modulator for FM/AM audio with PLL-outputFeatures● FM- and AM-audio modulator● Symmetrical RF-oscillator output for PLL-control● Sync level ..
TDA5670-5X ,Video modulator for FM/AM audio with PLL-outputFunctional Description and ApplicationThe monolitic integrated circuit TDA 5670-5X is especially su ..
TDA5708 ,Photo Diode Signal Processor
TDA5708 ,Photo Diode Signal Processor
TDA5709 ,Radial Error Signal Processor
TG2000F ,TV TUNER/ UHF RF AMPLIFIER APPLICATIONS)FEATURESo On account of this Device build in Bias Circuit, Cut downnumhnr rtf surtirlescInulllwul V ..
TG2006F ,GaAs Linear Integrated Circuit GaAs Monolithic 1.9 GHz Band Power Amplifier PHS, Digital Cordless TelecommunicationElectrical Characteristics (V = 3 V, V = (Note2), f = 1.9 GHz, Ta = 25°C, Z = Z = 50 Ω, 1/2 duty op ..
TG2200AF ,RF Cell PacksFEATURES0 LOW INSERTION LOSS : Loss=0.5dB (Typ.)0 HIGH ISOLATION : |SL=25dB (Typ.). CUNIRUL VULIAGI ..
TG2204F ,1.9GHz BAND ANTENNA SWITCH (PHS DIGITAL CORDLESS TELEPHONE)FEATURESo LOWINSERTION LOSS : Loss=0.5dB(Typ.)O HIGHTISOLATION : |SL=25dB(Typ.)O (ONTROI \IOITAGF . ..
TG2205F ,RF SPDT Switch (Application: PHS)Electrical Characteristics (V = 3 V, f = 1.907 GHz, Ta = 25°C, Z = Z = 50 Ω)DD g ITest Characteris ..
TG2210FT ,GaAs Linear Integrated Circuit GaAs Monolithic RF SPDT SwitchElectrical Characteristics (f 1 GHz, Ta 25°C, Zg Zl 50 )Test Characteri ..
TDA5670-5X
Video Modulator for FM/AM-Audio with ...
SIEMENS
Video Modulator for
FM/AM-Audio with
PLL-Output
Preliminary Data
Featu res
0 FM- and AM-audio modulator
o Symmetrical RF-oscillator output for PLL-control
o Sync level clamping of video input signal
o Controlling of peak white value
0 Continuous adjustment of modulation depth for
positive or negative values
TDA 5670-5X
Bipolar IC
F:::':::'::':':; "jgg5Y-
o Symmetrical mixer output with separate ground area P-DSO-20 -1
o Symmetrical oscillator with separate RF-ground
0 Low spurious radiation
0 High stability of the RF-oscillator frequency
o High stability of the audio oscillator
0 Internal reference voltage
0 12 V supply voltage
Type Ordering Code Package
TDA 5670-5X 067000-A5167 P-DSO-20-'l (SMD)
TDA 5670-5X Q67006-A5167 P-DSO-20-1 Tape & Reel
Functional Description and Application
The monolitic integrated circuit TDA 5670-5X is especially suitable as a modulator for the
48- to 860-MHz frequency range.
Video recorders, cable converters, TV-converter networks, demodulators, video
generators, video security systems, amateur TV-applications and personal computers.
Semiconductor Group 1
SII EM [ENS TDA 5670-5X
Circuit Description
Oscillator
The RF-oscillator is available at pins 3-7. The oscillator operates as a symmetrical
Colpitts circuit. The oscillator chip ground, pin 5, should be connected to ground at the
resonance circuit shielding point. An external oscillator can be injected inductively or
capacitively via pins 3 and 7. The layout of the PCB should be such as to provide a
minimum shielding attenuation between the oscillator pins 3-7 and modulator output pins
15-17 of approximately 80 dB.
For optimal residual carrier suppression, the symmetrical mixer outputs at pins 15, 17
should be connected to a matched balanced-to-unbalanced broadband transformer, e.g.
a Guanella transformer with good phase precision at oo and 1800. The transmission loss
should be less than 3 dB. In addition, an LC-low pass filter combination is required at the
output. The cut-off frequency of the low pass filter combination must exceed the
maximum operating frequency.
The video signal with the negative synchronous level is capacitively connected to pin 12.
The internal clamping circuit is referenced to the synchronizing level. Should the video
signal change by 6 dB, this change will be compensated by the resonance circuit which
is set by the peak white value. At pin 13, the current pulses of the peak white detector are
filtered through the capacitor which also determines the control time constant. The RF-
carrier switches from negative to positive video modulation, when pin 14 is connected
to ground. By varying the value of resistance R at pin 14 between oo ... 0 C2 the modulation
depth can be increased from 70% to 100% when the modulation is negative and
decreased from 100% to 70% when the modulation is positive.
Via pin 1, the audio signal is capacitively coupled to the AF-input for the FM-modulation
of the oscillator. A parallel resonance circuit is connected to the audio carrier oscillator at
pins 19, 20. The unloaded Q of the resonant circuit must be Q = 25 and the parallel
resistor RT = 8.2 kg to ensure a video to audio carrier ratio of 12.5 dB. At the same time,
the capacitative and/or inductive reactance for the resonance frequency should have a
value ofXC =XL '.i" 800 o.
Via pin 18, the audio signal is capacitively coupled to the AF-input for the AM-modulation
of the oscillator. This signal is forwarded to a mixer which is influenced by the AM-
modulation input of pin 18. The video to audio carrier ratio can be changed by connecting
an external voltage to pin 18, which deviates from the internal reference voltage.
Through an additional external dc voltage at pin 18, the set AM-modulation index can be
changed by overriding the internally adjusted control voltage for a fixed AM-modulation
index.
At the output of the above described mixer the FM and/or AM modulated audio signal is
added to the video signal and mixed with the oscillator signal in the RF-mixer.
Source
The internal reference voltage is available at pin 2 and has to be capacitively blocked
there.
Semiconductor Group 2
