TC7MH245FK ,Octal Bus TransceiverFeatures High speed: t = 4.0 ns (typ.) (V = 5 V) pd CC Low power dissipation: I = 4 µA (max) ( ..
TC7MH273FK ,Octal D-Type Flip Flop with ClearTC7MH273FK TOSHIBA CMOS Digital Integrated Circuit Silicon Monolithic TC7MH273FK Octal D-Type Fl ..
TC7MH367FK ,HEX Bus Buffer Non-Inverted, 3-State OutputsFeatures High speed: t = 3.8 ns (typ.) (V = 5 V) pd CC Low power dissipation: I = 4 µA (max) ( ..
TC7MH373FK ,Octal D-Type Latch with 3-State OutputTC7MH373FK TOSHIBA CMOS Digital Integrated Circuit Silicon Monolithic TC7MH373FK Octal D-Type La ..
TC7MH373FK ,Octal D-Type Latch with 3-State OutputFeatures High speed: t = 5.0 ns (typ.) (V = 5 V) pd CC Low power dissipation: I = 4 µA (max) ( ..
TC7MH374FK ,Octal D-Type Flip-Flop with 3-State OutputFeatures High speed: f = 185 MHz (typ.) (V = 5 V) max CC Low power dissipation: I = 4 µA (max) ..
TDA2040 ,20W Hi-Fi AUDIO POWER AMPLIFIERTDA204020W Hi-Fi AUDIO POWER AMPLIFIERDESCRIPTIONThe TDA2040 is a monolithic integrated circuit inP ..
TDA2040V ,20W Hi-Fi audio power amplifierTDA2040®20W Hi-Fi AUDIO POWER AMPLIFIERDESCRIPTIONThe TDA2040 is a monolithic integrated circuit in ..
TDA2040V ,20W Hi-Fi audio power amplifierTDA2040®20W Hi-Fi AUDIO POWER AMPLIFIERDESCRIPTIONThe TDA2040 is a monolithic integrated circuit in ..
TDA2040V ,20W Hi-Fi audio power amplifierTDA2040®20W Hi-Fi AUDIO POWER AMPLIFIERDESCRIPTIONThe TDA2040 is a monolithic integrated circuit in ..
TDA2048 , Multistandard quasi parallel-sound processor for Mono-TV-Sets
TDA2050 ,32W HI-FI AUDIO POWER AMPLIFIER
TC7MH245FK
Octal Bus Transceiver
TC7MH245FK TOSHIBA CMOS Digital Integrated Circuit Silicon Monolithic
TC7MH245FK Octal Bus Transceiver
The TC7MH245FK is an advanced high speed CMOS octal bus
transceiver fabricated with silicon gate C2 MOS technology.
It achieves the high speed operation similar to equivalent
bipolar schottky TTL while maintaining the CMOS low power
dissipation.
It is intended for two-way asynchronous communication
between data busses. The direction of data transmission is
determined by the level of the DIR input.
The enable input (G) can be used to disable the device so that
the busses are effectively isolated.
All inputs are equipped with protection circuits against static
discharge.
Features High speed: tpd = 4.0 ns (typ.) (VCC = 5 V) Low power dissipation: ICC = 4 µA (max) (Ta = 25°C) High noise immunity: VNIH = VNIL = 28% VCC (min) Balanced propagation delays: tpLH ≈ tpHL Wide operating voltage range: VCC (opr) = 2~5.5 V Low noise: VOLP = 1.0 V (max) Pin and function compatible with 74ALS245
Note: Do not apply a signal to any bus terminal when it is in the output mode. Damage may result.
All floating (high impedance) bus terminals must have their input levels fixed by means of pull up or pull down
resistors.
A parasitic diode is formed between the bus and VCC terminals. Therefore bus terminal can not be used to
interface 5 V to 3 V systems directly.
Weight: 0.03 g (typ.)