TC7MBD3245FK ,Octal Bus SwitchFeatures Pin Assignment (top view) Operating voltage: V = 4.5~5.5 V CC High speed: t = 0.25 ns ..
TC7MBD3245FK ,Octal Bus SwitchTC7MBD3245FK TOSHIBA CMOS Digital Integrated Circuit Silicon Monolithic TC7MBD3245FK Octal Bus S ..
TC7MBD3245FK ,Octal Bus SwitchFeatures Pin Assignment (top view) Operating voltage: V = 4.5~5.5 V CC High speed: t = 0.25 ns ..
TC7MBL3126CFK ,General-purpose bus switchFeatures • Operating voltage : V = 1.65 to 3.6 V CC• On-capacitance : C = 7.5 pF Switch On ( ..
TC7MBL3244AFK ,General-purpose bus switchTC7MBL3244AFT/FK TOSHIBA CMOS Digital Integrated Circuit Silicon Monolithic TC7MBL3244AFT, TC7MBL ..
TC7MBL3244AFT ,General-purpose bus switchAbsolute Maximum Ratings (Note) Characteristic Symbol Rating Unit Power supply range V −0.5 to 4.6 ..
TDA2003H ,10W CAR RADIO AUDIO AMPLIFIERELECTRICAL CHARACTERISTICS ( V = 14.4V, T = 25 °C unless otherwise specified)s ambSymbol Parameter ..
TDA2004 ,10 10W STEREO AMPLIFIER FOR CAR RADIOfeatures are :Low distortion.Low noise.High reliability of the chip and of the package withaddition ..
TDA2004R ,Dual SE output power amplifierFeatures■ Low distortion■ Low noise■ Protection against: – Output AC short circuit to ground Multiw ..
TDA2005 ,20W BRIDGE AMPLIFIER FOR CAR RADIOTDA2005 20W BRIDGE AMPLIFIER FOR CAR RADIOHigh output power : P = 10 + 10 W@R =2Ω,O Ld = 10% ; P = ..
TDA2005R ,Single BTL or dual SE output amplifierElectrical characteristics (stereo application) . . . 11Table 8. Recommended values of the comp ..
TDA2006 ,12W AUDIO AMPLIFIERTDA200612W AUDIO AMPLIFIERDESCRIPTIONThe TDA2006 is a monolithic integrated circuit inPentawatt pac ..
TC7MBD3245FK
Octal Bus Switch
TC7MBD3245FK TOSHIBA CMOS Digital Integrated Circuit Silicon Monolithic
TC7MBD3245FK Octal Bus Switch
The TC7MBD3245FK provides eight bits of high-speed
TTL-compatible bus switching in a standard ’245 device pinout.
The low on-state resistance of the switch allows connections to be
made with minimal propagation delay.
The device is organized as one 8-bit switch. When output
enable (OE) is low, the switch is on and port A is connected to port
B. When OE is high, the switch is open and a high-impedance
state exists between the two ports.
The internal diode which adds to power supply line is enable to
realize the shift of signal level from 5 V to 3.3 V . (Note 1)
All inputs are equipped with protection circuits against static
discharge.
Features Pin Assignment (top view) Operating voltage: VCC = 4.5~5.5 V High speed: tpd = 0.25 ns (max) Low on resistance: RON = 5 Ω (typ.) ESD performance: Human body model > ±2000 V Machine model > ±200 V Compatible with TTL outputs (control inputs) Package: VSSOP (US20) Pin compatible with the 74xx245 type. Functionally equivalent to (FST/CBT) 3245.
Note 1: In case that over-shoot noise is detected, this device
should be used with clamp diode to prevent the next stage
device from over-stress.
Weight: 0.03 g (typ.)
VCC 20
B1
B2
19
18
17 1A3
(top view)
B3 16
B4
B5
B6
15
14
13 5A7
B7
B8
12
11 GND
NC-No Internal Connection
