TB62209F ,Stepping Motor Driver IC Using PWM Chopper TypeFeatures • Bipolar stepping motor can be controlled by a single driver IC • Monolithic BiCD IC • Lo ..
TB62209F ,Stepping Motor Driver IC Using PWM Chopper TypeTB62209F TOSHIBA BiCD Processor IC Silicon Monolithic PreliminaryT B 6 2 2 0 9 F Stepping Motor D ..
TB62209FG ,Stepping motor driver ICTB62209FG TOSHIBA BiCD Processor IC Silicon Monolithic TB62209FG Stepping Motor Driver IC Using P ..
TB62214FG ,Stepping motor driver ICTB62214FG/FTG TOSHIBA BiCD Integrated Circuit Silicon Monolithic TB62214FG, TB62214FTG BiCD Cons ..
TB62214FTG ,Stepping motor driver ICabsolute maximum ratings） • Thermal shutdown (TSD), overcurrent shutdown (ISD), and power-on-resets ..
TB62218FTG ,Stepping motor driver ICTB62218FG/FTG TOSHIBA BiCD Integrated Circuit Silicon Monolithic TB62218FG, TB62218FTG BiCD Const ..
TC74HC4049AFN , CMOS Digital Integrated Circuit Silicon Monolithic
TC74HC42AF , CMOS Digital Integrated Circuit Silicon Monolithic BCD to Decimal Decoder
TC74HC42AFN , CMOS Digital Integrated Circuit Silicon Monolithic BCD to Decimal Decoder
TC74HC4511AP , CMOS Digital Integrated Circuit Silicon Monolithic BCD-to-7 Segment Latch/Decoder/Driver
TC74HC4511AP , CMOS Digital Integrated Circuit Silicon Monolithic BCD-to-7 Segment Latch/Decoder/Driver
TC74HC4538AFN , DUAL RETRIGGERABLE MONOSTABLE MULTIVIBRATOR
TB62209F
Stepping Motor Driver IC Using PWM Chopper Type
TB62209F TOSHIBA BiCD Processor IC Silicon Monolithic
T B 6 2 2 0 9 F Stepping Motor Driver IC Using PWM Chopper Type
The TB62209F is a stepping motor driver driven by chopper
micro-step pseudo sine wave.
The TB62209F integrates a decoder for CLK input in micro
steps as a system to facilitate driving a two-phase stepping motor
using micro-step pseudo sine waves. Micro-step pseudo sine
waves are optimal for driving stepping motors with low-torque
ripples and at low oscillation. Thus, the TB62209F can easily
drive stepping motors with low-torque ripples and at high
efficiency.
Also, TB62209F consists output steps by DMOS (Power MOS
FET), and that makes possible to control the output power
dissipation much lower than ordinary IC with bipolar transistor output.
The IC supports Mixed Decay mode for switching the attenuation ratio at chopping. The switching time for the
attenuation ratio can be switched in four stages according to the load.
Features Bipolar stepping motor can be controlled by a single driver IC Monolithic BiCD IC Low ON-resistance of Ron = 0.5 Ω (Tj = 25°C @1.0 A: typ.) Built-in decoder and 4-bit DA converters for micro steps Built-in ISD, TSD, VDD &VM power monitor (reset) circuit for protection Built-in charge pump circuit (two external capacitors) 36-pin power flat package (HSOP36-P-450-0.65) Output voltage: 40 V max Output current: 1.8 A/phase max 2-phase, 1-2 (type 2) phase, W1-2 phase, 2W1-2 phase, 4W1-2 phase, or motor lock mode can be selected. Built-in Mixed Decay mode enables specification of four-stage attenuation ratio. Chopping frequency can be set by external resistors and capacitors.
High-speed chopping possible at 100 kHz or higher.
Note: When using the IC, pay attention to thermal conditions. These devices are easy damage by high static
voltage. In regards to this, please handle with care.
Weight: g (typ.)
