STTH8S06FP ,Turbo 2 ultrafast high voltage rectifierelectrical characteristicsSymbol Parameter Test conditions Min. Typ Max. UnitT = 25 °C 20jI Reverse ..
STTH9012TV2 ,Ultrafast recoveryapplications. The improved performance in low leakage current, and therefore thermal runaway guard ..
STTS2002B2DN3F ,2.3 V memory module temperature sensor with a 2 Kb SPD EEPROMFeatures■ 2.3 V memory module temperature sensor with integrated 2 Kb SPD EEPROM ■ Forward compatib ..
STTS75M2F ,Digital temperature sensor and thermal watchdogFunctional description . . . . . . 173.1 Registers and register set formats . . . . . . 173 ..
STU100N3LF3 , N-channel 30V - 0.0045OHM - 80A - DPAK - IPAK Planar STripFET TM II Power MOSFET
STU10NM60N ,N-channel 600 V, 0.53 Ohm, 10 A, IPAK MDmesh(TM) II Power MOSFETElectrical characteristics(Tcase =25 °C unless otherwise specified)Table 5. On /off statesSymbol Pa ..
T6801 ,Single-channel driver 25 mA output with thermal monitoringFeatures Input Comparator with Schmitt-trigger Characteristic Input Clamping Current Capability o ..
T6801-TAQ ,Single-channel Driver IC with Driver IC with MonitoringFeatures Input Comparator with Schmitt-trigger Characteristic Input Clamping Current Capability o ..
T6816 ,40-V dual Hexdriver with serial input controlapplications and the industrial 24-V supply.It controls up to 12 different loads via a 16-bit dataw ..
T6816 ,40-V dual Hexdriver with serial input controlFeatures• Six High-side and Six Low-side Drivers Outputs Freely Configurable as Switch, Half Brid ..
T6816 ,40-V dual Hexdriver with serial input controlapplications.Overvoltage protection is matched to the requirements of the 24-V industrial voltagean ..
T6816-TIQ ,40-V Dual Hex Output Driver with Serial Input ControlFeatures• Six High-side and Six Low-side Drivers Outputs Freely Configurable as Switch, Half Brid ..
STTH8S06D-STTH8S06FP
Turbo 2 ultrafast high voltage rectifier
December 2007 Rev 1 1/8
STTH8S06 urbo 2 ultrafast high voltage rectifier
Features Ultrafast recovery Low reverse recovery current Reduces losses in diode and switching
transistor Low thermal resistance Higher frequency operation Insulated TO-220FPAC version Insulation voltage = 1500 V rms Package capacitance = 12 pF
DescriptionST's STTH8S06 is a state of the art ultrafast
recovery diode. By the use of 600 V Pt doping
planar technology, this diode will out-perform the power factor corrections circuits operating in
hardswitching conditions. The extremely low
reverse recovery current of the STTH8S06,
reduces significantly the switching power losses
of the MOSFET and thus increases the efficiency
of the application. This leads designers to reduce
the size of their heatsinks.
This device is also intended for applications in
power supplies and power conversions systems,
motor drive, and other power switching
applications.
Table 1. Device summary
Characteristics STTH8S06
2/8
1 Characteristics
To evaluate the maximum conduction losses use the following equation:
P = 1.20 x IF(AV) + 0.087 IF2 (RMS)
Table 2. Absolute ratings (limiting values)
Table 3. Thermal parameter
Table 4. Static electrical characteristics
Table 5. Dynamic electrical characteristics
STTH8S06 Characteristics
3/8
Figure 1. Forward voltage drop versus
forward current
Figure 2. Relative variation of thermal
impedance junction to case versus
pulse duration (TO-220AC)
Figure 3. Relative variation of thermal
impedance junction to case versus
pulse duration(TO-220FPAC)
Figure 4. Peak reverse recovery current
versus dIF /dt (typical values)
Characteristics STTH8S06
4/8
Figure 7. Junction capacitance versus reverse voltage applied (typical values)
Figure 5. Reverse recovery time versus dIF/dt
(typical values)
Figure 6. Reverse recovery charges versus
dIF/dt (typical values)
STTH8S06 Package information
5/8
2 Package information Epoxy meets UL94, V0 Cooling method: by conduction (C) Recommended torque value: 0.4 to 0.6 N·m
In order to meet environmental requirements, ST (also) offers these devices in ECOPACK®
packages. ECOP ACK® packages are Lead-free. The category of second level Interconnect
is marked on the package and on the inner box label, in compliance with JEDEC Standard
JESD97. The maximum ratings related to soldering conditions are also marked on the inner
box label.
ECOPACK is an ST trademark. ECOPACK specifications are available at: .
Table 6. TO-220AC dimensions
Package information STTH8S06
6/8
Table 7. TO-220FPAC dimensions