IC Phoenix
 
Home ›  SS105 > STLVDS31BD-STLVDS31BTR,HIGH SPEED DIFFERNTIAL LINE DRIVERS
STLVDS31BD-STLVDS31BTR Fast Delivery,Good Price
Part Number:
If you need More Quantity or Better Price,Welcom Any inquiry.
We available via phone +865332716050 Email
Partno Mfg Dc Qty AvailableDescript
STLVDS31BDSTN/a3629avaiHIGH SPEED DIFFERNTIAL LINE DRIVERS
STLVDS31BTRST ?N/a5000avaiHIGH SPEED DIFFERNTIAL LINE DRIVERS


STLVDS31BTR ,HIGH SPEED DIFFERNTIAL LINE DRIVERSSTLVDS31STLVDS3487HIGH SPEEDDIFFERENTIAL LINE DRIVERS ■ MEETS OR EXCEEDS THE REQUIREMENTS OF ANSI ..
STLVDS32BD ,HIGH SPEED DIFFERENTIAL LINE RECEIVERSPIN CONFIGURATIONSTLVDS32 STLVDS3486 STLVDS9637STLVDS32 PIN DESCRIPTION STLVDS3486 PIN DESCRIPTIONP ..
STLVDS32BDR ,HIGH SPEED DIFFERENTIAL LINE RECEIVERSelectrical characteristics of low voltage differentialand distance of data transfer is dependent up ..
STLVDS32BTR ,HIGH SPEED DIFFERENTIAL LINE RECEIVERSSTLVDS32/STLVDS3487STLVDS9637HIGH SPEEDDIFFERENTIAL LINE RECEIVERS■ MEETS OR EXCEEDS THEREQUIREMENT ..
STLVDS385B ,+3.3V PROGRAMMABLE LVDS TRANSMITTER 24-BIT FLAT PANEL DISPLAY (FPD) LINK-85MHZSTLVDS385+3.3V PROGRAMMABLE LVDS TRANSMITTER 24-BITFLAT PANEL DISPLAY (FPD) LINK-85MHZ

STLVDS31BD-STLVDS31BTR
HIGH SPEED DIFFERENTIAL LINE DRIVERS
1/11January 2002 MEETS OR EXCEEDS THE
REQUIREMENTS OF ANSI TIA/EIA-644
STANDARD LOW VOLTAGE DIFFERENTIAL SIGNALING
WITH TYPICAL OUTPUT VOLTAGE OF
350mV AND A 100Ω LOAD TYPICAL OUTPUT VOLTAGE RISE AND
FALL TIMES OF 750ps (400Mbps) TYPICAL PROPAGATION DELAY TIMES OF
1.7ns OPERATES FROM A SINGLE 3.3V SUPPLY POWER DISSIPATION 25mW TYPICAL PER
DRIVER AT 200MHz DRIVER AT HIGH IMPEDANCE WHEN
DISABLED OR WITH VCC =0V PIN COMPATIBLE WITH THE AM26LS31,
SN65LVD31, MC3487 AND SN65LVD3487 LOW VOLTAGE TTL (LVTTL) LOGIC INPUT
LEVELS
DESCRIPTION

The STLVDS31 and STLVDS3487 are quad
differential line drivers that implements the
electrical characteristics of low voltage differential
signaling (LVDS). This signaling technique lowers
the output voltage levels of 5V differential
standard levels (such as TIA/EIA-422B) to reduce
the power, increase the switching speeds and
allows operations with a 3.3V supply rail. Any of
the four current mode drivers will deliver a
minimum differential output voltage magnitude of
247mV into a 100Ω load when enabled.
The indended application of this device and
signalling tecnique is for point-to-point baseband
data transmission over controlled impedance
media approximately 100Ω. The transmission
media may be printed circuit board traces,
backplanes or cables. The ultimate rate and
distance of data transfer is dependent upon the
attenuation characteristics of the media and noise
coupling to the enviroment.
The STLVDS31 and STLVDS3487 are
characterized for operation from -40°C to 85°C .
ORDERING CODES
STLVDS31
STLVDS3487

HIGH SPEED
DIFFERENTIAL LINE DRIVERS
STLVDS31/STLVDS3487
2/11
PIN CONFIGURATION
STLVDS31 PIN DESCRIPTION STLVDS3487 PIN DESCRIPTION
LOGIC DIAGRAM AND LOGIC SYMBOL FOR STLVDS31
STLVDS31/STLVDS3487
3/11
LOGIC DIAGRAM AND LOGIC SYMBOL FOR STLVDS3487
STLVDS31 TRUTH TABLE STLVDS3487 TRUTH TABLE

L=Low level, H=High Level, X=Don’t care, Z= High Impedance
ABSOLUTE MAXIMUM RATINGS

Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these condition is
not implied.
Note 1: All voltages except differential I/O bus voltage, are with respect to the network ground terminal.
RECOMMENDED OPERATING CONDITIONS
STLVDS31/STLVDS3487
4/11
ELECTRICAL CHARACTERISTICS (Over recommended operating conditions unless otherwise noted.

All typical values are at TA = 25°C, and VCC = 3.3V)
STLVDS31/STLVDS3487
5/11
SWITCHING CHARACTERISTICS (Unless otherwise noted. Typical values are referred to T
A = 25°C
and VCC = 3.3V)
Note 1: tsk(O) is the maximum delay time difference between drivers on the same device.
RNote 1: RS-232 IN to TTL-CMOS OUT (from 50% to 50%)
Figure 1 : Voltage and Current Definitions
STLVDS31/STLVDS3487
6/11
Figure 2 : Test Circuit, Timing And Voltage Definitions For Differential Output Signal

Note A: All input pulse are supplied by a generator having the following characteristics: tr or tf ≤ 1ns, pulse repetition rate (PRR) = 50Mpps,
pulse width = 10 ± 0.2ns.
Note B: CL includes instrumentation and fixture capacitance within 6mm of the D.U.T.
Figure 3 : Test Circuit And Definitions For The Driver Common Mode Output Voltage

Note A: All input pulse are supplied by a generator having the following characteristics: tr or tf ≤ 1ns, pulse repetition rate (PRR) = 50Mpps,
pulse width = 10 ± 0.2ns.
Note B: CL includes instrumentation and fixture capacitance within 6mm of the D.U.T
Note C: The measurement of VOC(PP) is made on test equipment with a -3dB bandwidth of at least 300MHz
ic,good price


TEL:86-533-2716050      FAX:86-533-2716790
   

©2020 IC PHOENIX CO.,LIMITED