ST7MDT10-EMU3 ,ST7-EMU3features, including advanced breakpoints and performance ST7analysis. In addition, the EMU3 include ..
ST7MDTU3-EPB/EU ,ST7 One position programming board,APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY ..
ST7MDTU3-EPB/US ,ST7 One position programming board,Features■ In-circuit programming or in-situ programming of various ST7 devices (depending on the EP ..
ST8004CD ,SMARTCARD INTERFACEST8004SMARTCARD INTERFACE
ST7MDT10-EMU3
ST7-EMU3
DATA BRIEF
ST7-EMU3Full-Featured, Real Time Emulator Series for ST7
The ST7-EMU3 series of emulators is the third
generation of high-end emulators for ST7. EMU3
series emulators are designed to speed up the
development of complex software applications for
ST7 microcontrollers by providing a complete range
of advanced debugging features. In combination
with ST7 Visual Develop (STVD7) and ST7 Visual
Programmer (STVP7), this series of emulators
provide you with unprecedented control of
application development – from building and
debugging your application, to programming your
ST7 microcontroller.
The EMU3 series emulators deliver start-to-finish
control of application development by providing you
with both emulation and In-Circuit Communication
(ICC) configurations from a single platform.
In the emulation configuration, the EMU3 probe and
STVD7 software allow you to debug your program
while connected to your application board in place
of your target ST7. This configuration gives you the
most complete range of debugging features,
including advanced breakpoints and performance
analysis. In addition, the EMU3 includes everything
you will need to connect it to your application board.
The ICC configuration allows you to In-Circuit
Debug (ICD) your application while it runs on an
ST7 that is installed on your application board and
that has the necessary debug modules. When you
are finished debugging your application, the ICC
configuration allows you to In-Circuit Program (ICP)
your application to your ST7 microcontrollers.
Emulator Architecture
ST Micro Connect – Provides the communication interface with the host PC via parallel, USB or
Ethernet connection when working in both the
Emulation and ICC configurations.
EMU3 Probe – Contains the system’s emulation boards including the Target Emulation Board (TEB),
which allows it to emulate a specific family of ST7
devices. It connects to your application board via
furnished adapters and sockets that are specific to
the target device’s package.
ICC Add-on – Permits communication with the ST7 on your application board for in-circuit debugging
and in-circuit programming. Requires installation of
a 10-pin, ICC connector on your application board.
ST7 Visual Develop – Integrated Development Environment (IDE) that runs on the host PC
connected to the emulator and allows you to build
and debug your application software and then
program it to your target ST7.
ST7 Visual Programmer – Software programming interface that runs on the host PC connected to the
emulator and allows you to program your
application to your ST7.
Figure 1: System configurations
ST7-EMU3
Emulation FeaturesIn the emulation configuration, the EMU3 series
emulators in combination with STVD7, provide the
most advanced and complete range of debugging
features, including: Unlimited breakpoints with counter and
condition Two output triggers Nine external input triggers 256K real-time trace recording with timestamp Read/write on the fly Low voltage emulation from 1.8 to 5.5 V Programmable Clock frequency From 32 KHz
up to 16 MHz Performance Analysis Four-level logic sequencer that allows you to
perform specific actions such as: Stop program execution Start/stop trace recording, Record a snapshot in the trace, Output signals via the two output triggers
These actions can be coordinated with the
occurrence of a specific event or a series of
events such as: an event at an address or range of addresses, a specific data value with bit mask, a read, write or read/write access, stack operation access
...or any combination of these.
In-Circuit Debugging FeaturesThe EMU3 series emulators and the STVD7
integrated development environment also allow
you to in-circuit debug your application as it runs on
an ST7 with debug modules.
ICD features include: Real-time control of application execution Reading and writing of memory contents and
ST7 registers Configuration of option byte Unlimited software breakpoints in address
ranges corresponding to RAM and XFlash
memory Advanced breakpoints including Break on data value at a given address. Break on Opcode Fetch (within address range,
outside of address range) Break on two sequential Opcode Fetch's Break on data access (within address range,
outside of an address range, at one of two
addresses) Break on Opcode Fetch, or data access at
given addresses. Break on conditional stack write, or Opcode
Fetch at a given address Break on conditional stack write, or data access
at a given address.
In-Circuit Programming FeaturesThe EMU3 series emulators along with STVP7, or
STVD7 software, allow you to in-circuit program
ST7 devices with Flash memory. You can program
your ST7s on your application board (via the ICC
Add-on and the ICC connector installed on the your
application board), or on an ST7SBxx socket
board.
For more information...The following documents are available for free
download from our internet site:
ST7-EMU3 Emulator User Manual - Information about setting up an ST7-EMU3 series emulator in
the emulation or ICC configuration. This manual
provides information that is common to all
emulators in the EMU3 series.
ST7xxxx-EMU3 Probe User Guide - Information about connecting the EMU3 emulator to your
application board in the emulation configuration.
These documents provide information that is
specific to each type of EMU3 emulator
(ST7MDTxx-EMU3 emulator).
ST7 Visual Develop User Manual - Information and tutorials to help you build and debug your
application software and program it to your ST7
using the STVD7 Integrated Development
Environment and an ST7-EMU3 series emulator.
ST7 Visual Programmer online help - Information to help you program your application to
your ST7 using this Windows-based programming
software and an ST7-EMU3 series emulator.
ST7xxxx Datasheet - Complete information about the features of your target ST7 microcontroller.
ST7-EMU3. consequences
of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is
granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are
subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products
are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics.
The ST logo is a registered trademark of STMicroelectronics.
All other names are the property of their respective owners
© 2005 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
- Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
:
www.ic-phoenix.com
.