SN75ALS192DRG4 ,Quadruple Differential Line Driver 16-SOIC 0 to 70maximum ratings” may cause permanent damage to the device. These are stress ratings only, andfuncti ..
SN75ALS192N ,Quadruple Differential Line Drivermaximum ratings” may cause permanent damage to the device. These are stress ratings only, andfuncti ..
SN75ALS192NSR ,Quadruple Differential Line Drivermaximum ratings over operating free-air temperature range (unless otherwise noted)Supply voltage, V ..
SN75ALS192NSRG4 ,Quadruple Differential Line Driver 16-SO 0 to 70logic diagram (positive logic)4G122G1 1Y1A 31Z67 2Y52A2Z103Y93A113Z144Y154A134Z2POST OFFICE BOX 655 ..
SN75ALS193DRG4 ,Quadruple Differential Line Receiver 16-SOIC 0 to 70features 3-state outputs thatpermit direct connection to a bus-organized system with a fail-safe de ..
SN75ALS193J ,Quadruple Differential Line Receivermaximum ratings over operating free-air temperature range (unless otherwise noted)Supply voltage, V ..
SPI07N60C3 ,for lowest Conduction Losses & fastest SwitchingCharacteristicsParameter Symbol Values Unitmin. typ. max.R - - 1.5 K/WThermal resistance, junction ..
SPI08N50C3 ,for lowest Conduction Losses & fastest SwitchingCharacteristics, at T =25°C unless otherwise specifiedjParameter Symbol Conditions Values Unitmin. ..
SPI08N80C3 ,for lowest Conduction Losses & fastest SwitchingPlease note: Infineon has changed the CoolMOS 800V C2 marking to C3. 800V C2 ...FeatureR 0.65 ΩDS(on)• New revolutionary high voltage technologyI 8 AD• Ultra low gate chargeP-TO22 ..
SPI11N60C3 ,for lowest Conduction Losses & fastest SwitchingCharacteristicsParameter Symbol Conditions Values Unitmin. typ. max.Transconductance g V ≥2*I *R , ..
SPI11N60S5 ,for lowest Conduction LossesFeatureR 0.38 ΩDS(on)• New revolutionary high voltage technologyI 11 AD• Ultra low gate chargeP-TO2 ..
SPI11N65C3 ,for lowest Conduction Losses & fastest SwitchingCharacteristicsParameter Symbol Values Unitmin. typ. max.R - - 1 K/WThermal resistance, junction - ..
SN75ALS192-SN75ALS192D-SN75ALS192DR-SN75ALS192DR G4-SN75ALS192DRG4-SN75ALS192N-SN75ALS192NSR-SN75ALS192NSRG4
Quadruple Differential Line Driver
Single 5-V Supply Operation High Output Impedance in Power-OffCondition Complementary Output-Enable Inputs Improved Replacement for the AM26LS31
descriptionThe four differential line drivers are designed for data transmission over twisted-pair or parallel-wire
transmission lines. They meet the requirements of ANSI Standard EIA/TIA-422-B and ITU
Recommendations V.11 and are compatible with 3-state TTL circuits. Advanced low-power Schottky
technology provides high speed without the usual power penalties. Standby supply current is typically only
26 mA, while typical propagation delay time is less than 10 ns.
High-impedance inputs maintain low input currents, less than 1 μA for a high level and less than 100 μA for a
low level. Complementary output-enable inputs (G and G) allow these devices to be enabled at either a high
input level or low input level. The SN75ALS192 is capable of data rates in excess of 20 Mbit/s and is designed
to operate with the SN75ALS193 quadruple line receiver.
The SN75ALS192 is characterized for operation from 0°C to 70°C.
FUNCTION TABLE
(each driver)H = high level, L = low level, X = irrelevant,
Z = high impedance (off)
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
GND