SN74LVTH18504APMR ,3.3-V ABT Scan Test Devices With 20-Bit Universal Bus Transceivers SN54LVTH18504A, SN54LVTH182504A, SN74LVTH18504A, SN74LVTH182504A 3.3-V ABT SCAN TEST DEVICESWITH 2 ..
SN74LVTH18504APMR ,3.3-V ABT Scan Test Devices With 20-Bit Universal Bus Transceivers SN54LVTH18504A, SN54LVTH182504A, SN74LVTH18504A, SN74LVTH182504A 3.3-V ABT SCAN TEST DEVICESWITH 2 ..
SN74LVTH18512 ,3.3-V ABT Scan Test Devices With 18-Bit Universal Bus Transceivers SN54LVTH18512, SN54LVTH182512, SN74LVTH18512, SN74LVTH182512 3.3-V ABT SCAN TEST DEVICESWITH 18-BI ..
SN74LVTH18512DGG , 3.3-V ABT SCAN TEST DEVICES WITH 18-BIT UNIVERSAL BUS TRANSCEIVERS
SN74LVTH18512DGGR ,3.3-V ABT Scan Test Devices With 18-Bit Universal Bus Transceivers SN54LVTH18512, SN54LVTH182512, SN74LVTH18512, SN74LVTH182512 3.3-V ABT SCAN TEST DEVICESWITH 18-BI ..
SN74LVTH18514 ,3.3-V ABT Scan Test Devices With 20-Bit Universal Bus Transceivers SN54LVTH18514, SN54LVTH182514, SN74LVTH18514, SN74LVTH182514 3.3-V ABT SCAN TEST DEVICESWITH 20-BI ..
SP730EK-4-375 , Microprocessor Supervisory Circuit with Pull Up Resistor
SP7614EC6 , Low Dropout LED Driver for any Color LED
SP7616ER-L , High Accuracy 4-Channel Low Side LED Driver for CCFL Replacement
SP7651ER , Wide Input Voltage Range 3Amp 900kHz Buck Regulator
SP7651ER , Wide Input Voltage Range 3Amp 900kHz Buck Regulator
SP7651ER , Wide Input Voltage Range 3Amp 900kHz Buck Regulator
SN74LVTH18504A-SN74LVTH18504APM-SN74LVTH18504APMR
3.3-V ABT Scan Test Devices With 20-Bit Universal Bus Transceivers
Mixed-Mode Signal Operation (5-V Input
and Output Voltages With 3.3-V VCC) Support Unregulated Battery Operation
Down to 2.7 V UBT (Universal Bus Transceiver)
Combines D-Type Latches and D-Type
Flip-Flops for Operation in Transparent,
Latched, or Clocked Mode Bus Hold on Data Inputs Eliminates the
Need for External Pullup/Pulldown
Resistors B-Port Outputs of ’LVTH182504A Devices
Have Equivalent 25-W Series Resistors, So
No External Resistors Are Required
Instructions and Optional CLAMP and
HIGHZ
– Parallel-Signature Analysis at Inputs
– Pseudo-Random Pattern Generation
From Outputs
– Sample Inputs/Toggle Outputs
– Binary Count From Outputs
– Device Identification
– Even-Parity Opcodes Packaged in 64-Pin Plastic Thin Quad Flat
(PM) Packages Using 0.5-mm
Center-to-Center Spacings and 68-Pin
Ceramic Quad Flat (HV) Packages Using
25-mil Center-to-Center Spacings
descriptionThe ’LVTH18504A and ’LVTH182504A scan test devices with 20-bit universal bus transceivers are members
of the Texas Instruments (TI) SCOPE testability integrated-circuit family. This family of devices supports
IEEE Std 1149.1-1990 boundary scan to facilitate testing of complex circuit-board assemblies. Scan access to
the test circuitry is accomplished via the 4-wire test access port (TAP) interface.
Additionally, these devices are designed specifically for low-voltage (3.3-V) VCC operation, but with the
capability to provide a TTL interface to a 5-V system environment.
In the normal mode, these devices are 20-bit universal bus transceivers that combine D-type latches and D-type
flip-flops to allow data flow in transparent, latched, or clocked modes. The test circuitry can be activated by the
TAP to take snapshot samples of the data appearing at the device pins or to perform a self-test on the
boundary-test cells. Activating the TAP in the normal mode does not affect the functional operation of the
SCOPE universal bus transceivers.
Data flow in each direction is controlled by output-enable (OEAB and OEBA), latch-enable (LEAB and LEBA),
clock-enable (CLKENAB and CLKENBA), and clock (CLKAB and CLKBA) inputs. For A-to-B data flow, the
device operates in the transparent mode when LEAB is high. When LEAB is low, the A-bus data is latched while
CLKENAB is high and/or CLKAB is held at a static low or high logic level. Otherwise, if LEAB is low and
CLKENAB is low, A-bus data is stored on a low-to-high transition of CLKAB. When OEAB is low, the B outputs
are active. When OEAB is high, the B outputs are in the high-impedance state. B-to-A data flow is similar to
A-to-B data flow, but uses the OEBA, LEBA, CLKENBA, and CLKBA inputs.
In the test mode, the normal operation of the SCOPE universal bus transceivers is inhibited, and the test circuitry
is enabled to observe and control the I/O boundary of the device. When enabled, the test circuitry performs
boundary-scan test operations according to the protocol described in IEEE Std 1149.1-1990.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
