IC Phoenix
 
Home ›  SS53 > SN74ACT8990FN-SN74ACT8990FNR,Test-Bus Controllers IEEE Std 1149.1 (JTAG) TAP Masters With 16-Bit Generic Host Interfaces
SN74ACT8990FN-SN74ACT8990FNR Fast Delivery,Good Price
Part Number:
If you need More Quantity or Better Price,Welcom Any inquiry.
We available via phone +865332716050 Email
Partno Mfg Dc Qty AvailableDescript
SN74ACT8990FNTIN/a1avaiTest-Bus Controllers IEEE Std 1149.1 (JTAG) TAP Masters With 16-Bit Generic Host Interfaces
SN74ACT8990FNRTIN/a1000avaiTest-Bus Controllers IEEE Std 1149.1 (JTAG) TAP Masters With 16-Bit Generic Host Interfaces


SN74ACT8990FNR ,Test-Bus Controllers IEEE Std 1149.1 (JTAG) TAP Masters With 16-Bit Generic Host Interfaces SN54ACT8990, SN74ACT8990 TEST-BUS CONTROLLERSIEEE STD 1149.1 (JTAG) TAP MASTERS WITH 16-BIT GENERI ..
SN74ACT8994FN ,DIGITAL BUS MONITOR IEEE STD 1149.1 JTAG SCAN-CONTROLLED LOGIC/SIGNATURE ANALYZER
SN74ACT8997DW ,Scan Path Linkers With 4-Bit Identification Buses Scan-Controlled TAP Concatenators SN54ACT8997, SN74ACT8997 SCAN-PATH LINKERS WITH 4-BIT IDENTIFICATION BUSESSCAN-CONTROLLED IEEE STD ..
SN74AHC00D ,Quadruple 2-Input Positive-NAND Gates SCLS227J –OCTOBER 1995–REVISED MAY 2013QUADRUPLE 2-INPUT POSITIVE-NAND GATESCheck for Samples: SN5 ..
SN74AHC00DB , QUADRUPLE 2-INPUT POSITIVE-NAND GATES
SN74AHC00DBLE ,Quadruple 2-Input Positive-NAND GatesELECTRICAL CHARACTERISTICSover operating free-air temperature range (unless otherwise noted)T = –55 ..
SN74LS283DR , 4 BIT BINARY FULL ADDERS WITH FAST CARRY
SN74LS283N ,4-BIT BINARY FULL ADDER WITH FAST CARRYSN54/74LS2834-BIT BINARY FULL ADDERWITH FAST CARRYThe SN54 /74LS283 is a high-speed 4-Bit Binary Fu ..
SN74LS290N ,DECADE COUNTER; 4-BIT BINARY COUNTER
SN74LS292N ,Programmable Frequency Divider / Digital TimerFeatures 3 DescriptionThe SN74LS29x devices are programmable1• Count Divider Chainfrequency divider ..
SN74LS294N ,Programmable Frequency Divider / Digital TimerFeatures 3 DescriptionThe SN74LS29x devices are programmable1• Count Divider Chainfrequency divider ..
SN74LS297N ,Digital Phase-Locked-Loop Filters


SN74ACT8990FN-SN74ACT8990FNR
Test-Bus Controllers IEEE Std 1149.1 (JTAG) TAP Masters With 16-Bit Generic Host Interfaces
Control Operation of Up to Six ParallelTarget Scan Paths Accommodate Pipeline Delay to Target of
Up to 31 Clock Cycles
Scan Data Up to 232 Clock Cycles EPIC (Enhanced-Performance Implanted
CMOS) 1-m m Process
Packaged in 44-Pin Plastic Leaded Chip
Carrier (FN), 68-Pin Ceramic Pin Grid Array
(GB), and 68-Pin Ceramic Quad Flat
Packages (HV)


description

The ’ACT8990 test-bus controllers (TBC) are members of the Texas Instruments SCOPE testability
integrated-circuit family. This family of components supports IEEE Standard 1149.1-1990 (JTAG) boundary
scan to facilitate testing of complex circuit-board assemblies. The ’ACT8990 differ from other SCOPE
integrated circuits. Their function is to control the JTAG serial-test bus rather than being target
boundary-scannable devices.
The required signals of the JTAG serial-test bus – test clock (TCK), test mode select (TMS), test data input (TDI),
and test data output (TDO) can be connected from the TBC to a target device without additional logic. This is
done as a chain of IEEE Standard 1149.1-1990 boundary-scannable components that share the same
serial-test bus. The TBC generates TMS and TDI signals for its target(s), receives TDO signals from its target(s),
and buffers its test clock input (TCKI) to a test clock output (TCKO) for distribution to its target(s). The TMS, TDI,
and TDO signals can be connected to a target directly or via a pipeline, with a retiming delay of up to 31 bits.
Since the TBC can be configured to generate up to six separate TMS signals [TMS (5 –0)], it can be used to
control up to six target scan paths that are connected in parallel (i.e., sharing common TCK, TDI, and TDO
signals).
While most operations of the TBC are synchronous to TCKI, a test-off (TOFF) input is provided for output control
of the target interface, and a test-reset (TRST) input is provided for hardware/software reset of the TBC. In
addition, four event [EVENT (3–0)] I/Os are provided for asynchronous communication to target device(s).
Each event has its own event generation/detection logic, and detected events can be counted by two 16-bit
counters.
The TBC operates under the control of a host microprocessor/microcontroller via the 5-bit address bus
[ADRS (4–0)] and the 16-bit read/write data bus [DATA (15–0)]. Read (RD) and write (WR) strobes are
implemented such that the critical host-interface timing is independent of the TCKI period. Any one of
24 registers can be addressed for read and/or write operations. In addition to control and status registers, the
TBC contains two command registers, a read buffer, and a write buffer. Status of the TBC is transmitted to the
host via ready (RDY) and interrupt (INT) outputs.
Major commands can be issued by the host to cause the TBC to generate the TMS sequences necessary to
move the target(s) from any stable test-access-port (TAP) controller state to any other stable TAP state, to
execute instructions in the Run-Test/Idle TAP state, or to scan instruction or test data through the target(s). A
32-bit counter can be preset to allow a predetermined number of execution or scan operations.
Serial data that appears at the selected TDI input (TDI1 or TDI0) is transferred into the read buffer, which can
be read by the host to obtain up to 16 bits of the serial-data stream. Serial data that is transmitted from the TDO
output is written by the host to the write buffer.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
ic,good price


TEL:86-533-2716050      FAX:86-533-2716790
   

©2020 IC PHOENIX CO.,LIMITED