SN65LBC175ADR ,Quadruple RS-485 Differential Line ReceiversfeaturesESD protection to 6 kV, making it suitable for high-speed multipoint data transmission appl ..
SN65LBC175D ,Quadruple Low-Power Differential Line Receiverfeatures high impedance, hysteresis for increased noise immunity, andsensitivity of ±200 mV over a ..
SN65LBC175DR ,Quadruple Low-Power Differential Line Receivermaximum ratings” may cause permanent damage to the device. These are stress ratings only, andfuncti ..
SN65LBC175DRG4 ,Quadruple Low-Power Differential Line Receiver 16-SOIC -40 to 85logic diagram (positive logic)44EN1,2EN1,2EN2231A1A 31Y11 1Y1B1B62A 567 2Y2A 52B7 2Y2B123,4EN EN123 ..
SN65LBC175DW ,Quadruple Low-Power Differential Line Receiver SLLS171G − OCTOBER 1993 − REVISED ..
SN65LBC175DWR ,Quadruple Low-Power Differential Line Receiverfeatures high impedance, hysteresis for increased noise immunity, andsensitivity of ±200 mV over a ..
SN74HC42N ,4-Line To 10-Line Decoders (1 of 10) SCLS091D − DECEMBER 1982 − REVISED SEPTEMBER 2003 ..
SN74HC42N ,4-Line To 10-Line Decoders (1 of 10)maximum ratings” may cause permanent damage to the device. These are stress ratings only, andfuncti ..
SN74HC4724N , 8-BIT ADDRESSABLE LATCHES
SN74HC4851DR ,8-Channel Analog Multiplexer/Demultiplexer with Injection-Current Effect Controlmaximum ratings over operating free-air temperature range (unless otherwise noted)Supply voltage ra ..
SN74HC4851PW ,8-Channel Analog Multiplexer/Demultiplexer with Injection-Current Effect Controlfeatures injection-current effect control, which has excellent value in automotive applications whe ..
SN74HC4851PWG4 , 8-CHANNEL ANALOG MULTIPLEXER/DEMULTIPLEXER WITH INJECTION-CURRENT EFFECT CONTROL
SN65LBC175AD-SN65LBC175ADR
Quadruple RS-485 Differential Line Receivers
ESD Protection on Bus Inputs 6 kV Common-Mode Bus Input RangeVto12V Propagation Delay Times <16 ns Low Standby Power Consumption <20 µA Pin-Compatible Upgrade for MC3486,DS96F175, LTC489, and SN75175
descriptionThe SN65LBC175A and SN75LBC175A are
quadruple differential line receivers with 3-state
outputs, designed for TIA/EIA-485 (RS-485),
TIA/EIA-422 (RS-422), and ISO 8482 (Euro
RS-485) applications.
These devices are optimized for balanced
multipoint bus communication at data rates up to
and exceeding 50 million bits per second. The
transmission media may be twisted-pair cables,
printed-circuit board traces, or backplanes. The
ultimate rate and distance of data transfer is
dependent upon the attenuation characteristics of
the media and the noise coupling to the
environment.
Each receiver operates over a wide range of positive and negative common-mode input voltages, and features
ESD protection to 6 kV, making it suitable for high-speed multipoint data transmission applications in harsh
environments. These devices are designed using LinBiCMOS�, facilitating low power consumption and
inherent robustness.
Two EN inputs provide pair-wise enable control, or these can be tied together externally to enable all four drivers
with the same signal.
The SN75LBC175A is characterized for operation over the temperature range of 0°C to 70°C. The
SN65LBC175A is characterized over the temperature range from −40°C to 85°C.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
LinBiCMOS is a trademark of Texas Instruments.
1The signaling rate of a line is the number of voltage transitions that are made per second expressed in the units bps (bits per second).
