SN65LBC031QDRG4 ,High-Speed Controller Area Network (CAN) Transceiver 8-SOIC -40 to 125maximum ratings” may cause permanent damage to the device. These are stress ratings only, andfuncti ..
SN65LBC170DB ,Triple Differential Transceiverslogic diagramperipheral buses with twin axial, ribbon, or1DIRtwisted-pair cabling. These devices ar ..
SN65LBC170DW ,Triple Differential Transceiversmaximum ratings” may cause permanent damage to the device. These are stress ratings only, andfuncti ..
SN65LBC171DB ,Triple Differential TransceiversSN65LBC171, SN75LBC171 TRIPLE DIFFERENTIAL TRANSCEIVERS SLLS460A – NOVEMBER 2000 – REVISED FEBRUARY ..
SN65LBC171DB ,Triple Differential Transceiverslogic diagram* Power-Up, Power-Down Glitch-FreeCDEOperation* Pin-Compatible With the SN75ALS1711DE1 ..
SN65LBC171DBR ,Triple Differential Transceiverslogic diagram* Power-Up, Power-Down Glitch-FreeCDEOperation* Pin-Compatible With the SN75ALS1711DE1 ..
SN74HC4060NSR ,14-Stage Asynchronous Binary Counters And Oscillatorslogic diagram (positive logic)R R R R R R R R RT T T T T T T T T4 614 13 15 1 2 3Q Q Q Q Q Q Q QF G ..
SN74HC4060PW ,14-Stage Asynchronous Binary Counters And Oscillatorsmaximum ratings over operating free-air temperature range (unless otherwise noted)Supply voltage ra ..
SN74HC4060PWR ,14-Stage Asynchronous Binary Counters And Oscillatorsmaximum ratings over operating free-air temperature range (unless otherwise noted)Supply voltage ra ..
SN74HC4066 ,Quadruple Bilateral Analog SwitchesFeatures... 18.4 Device Functional Modes.... 122 Applications..... 19 Application and Implementatio ..
SN74HC4066D ,Quadruple Bilateral Analog SwitchesBlock Diagram... 124 Revision HistoryNOTE: Page numbers for previous revisions may differ from page ..
SN74HC4066DB , QUADRUPLE BILATERAL ANALOG SWITCH
SN65LBC031QDR-SN65LBC031QDRG4
HIGH-SPEED CONTROLLER AREA NETWORK (CAN) TRANSCEIVERS
Bus Outputs Short-Circuit-Protected toBattery Voltage and Ground Thermal Shutdown Available in Q-Temp Automotive
– HighRel Automotive Applications
– Configuration Control/Print Support
– Qualification to Automotive Standards
descriptionThe SN75LBC031 is a CAN transceiver used as
an interface between a CAN controller and the
physical bus for high speed applications of up to
500 kBaud. The device provides transmit
capability to the differential bus and differential
receive capability to the controller. The transmitter
outputs (CANH and CANL), feature internal
transition regulation to provide controlled
symmetry resulting in low EMI emissions. Both
transmitter outputs are fully protected against battery short circuits and electrical transients that can occur on
the bus lines. In the event of excessive device power dissipation the output drivers are disabled by the thermal
shutdown circuitry at a junction temperature of approximately 160°C. The inclusion of an internal pullup resistor
on the transmitter input ensures a defined output during power up and protocol controller reset. For normal
operation at 500 kBaud the ASC terminal is open or tied to GND. For slower speed operation at 125 kBaud the
bus output transition times can be increased to reduce EMI by connecting the ASC terminal to VCC . The receiver
includes an integrated filter that suppresses the signal into pulses less than 30 ns wide.
The SN75LBC031 is characterized for operation from –40°C to 85°C. The SN65LBC031 is characterized for
operation from –40°C to 125°C. The SN65LBC031Q is characterized for operation over the automotive
temperature range of –40°C to 125°C.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
FUNCTION TABLEL = low, H = high
REF
TERMINAL FUNCTIONS
