SN65HVD251DR ,Standby ModeFeatures 3 DescriptionThe HVD251 is intended for use in applications1• Drop-In Improved Replacement ..
SN65HVD251DRG4 ,High Speed CAN Transceiver with Short Loop Delay 8-SOIC -40 to 125Maximum RatingsMIN MAX UNITSupply voltage, V –0.3 7 VCCVoltage at any bus pin(CANH or CANL) –36 36 ..
SN65HVD251P ,Standby ModeTHERMAL CHARACTERISTICS table values....... 7• Changed the ABSOLUTE MAXIMUM POWER DISSIPATION RATIN ..
SN65HVD251PE4 ,High Speed CAN Transceiver with Short Loop Delay 8-PDIP -40 to 125Block Diagramdevice enters a low-current standby mode where theV (3)CCdriver is switched off and th ..
SN65HVD3080EDGS ,Low-Power RS-485 Full-Duplex Drivers/Receivers 10-VSSOP -40 to 85 SLLS771E –NOVEMBER 2006–REVISED NOVEMBER 2012SUPPLY CURRENTover recommended operating conditions u ..
SN65HVD3080EDGSR ,Low-Power RS-485 Full-Duplex Drivers/Receivers 10-VSSOP -40 to 85FEATURESDGS PACKAGE• Low Quiescent Power(TOP VIEW)– 375μA (Typical) Enabled Mode– 2 nA (Typical) Sh ..
SN74HC374NSR ,Octal Edge-Triggered D-Type Flip-Flops With 3-State Outputsmaximum ratings” may cause permanent damage to the device. These are stress ratings only, andfuncti ..
SN74HC374PWLE ,Octal Edge-Triggered D-Type Flip-Flops With 3-State Outputs/sc/package.Please be aware that an important notice concerning availability, standard warranty, an ..
SN74HC374PWR ,Octal Edge-Triggered D-Type Flip-Flops With 3-State Outputsmaximum ratings” may cause permanent damage to the device. These are stress ratings only, andfuncti ..
SN74HC377 ,Octal D-Type Flip-Flops With Clock Enablemaximum ratings” may cause permanent damage to the device. These are stress ratings only, andfuncti ..
SN74HC377DW ,Octal D-Type Flip-Flops With Clock Enablemaximum ratings over operating free-air temperature range (unless otherwise noted)Supply voltage ra ..
SN74HC377DWR ,Octal D-Type Flip-Flops With Clock Enable/sc/package.Please be aware that an important notice concerning availability, standard warranty, an ..
SN65HVD251-SN65HVD251D-SN65HVD251DG4-SN65HVD251DR-SN65HVD251DRG4-SN65HVD251P-SN65HVD251PE4
Standby Mode
GND
VCC
SLOPE
CONTROLand
MODELOGIC
Overtemperature
Sensor
VCC(3)
Driver
Vcc(3)
VCC(3)VCC/2
Product
Folder
Sample &
Buy
Documents
Software
Support &
Community
SN55HVD251, SN65HVD251SLLS545G–NOVEMBER 2002–REVISED OCTOBER 2015
SNx5HVD251 Industrial CAN Bus Transceiver Features 3 DescriptionThe HVD251is intended for use in applications Drop-In Improved Replacement for the employing the Controller Area Network (CAN) serialPCA82C250 and PCA82C251 communication physical layerin accordance with the• Bus-Fault Protectionof ±36V ISO 11898 Standard. The HVD251 provides Meetsor Exceeds ISO 11898 differential transmit capability to the bus and
differential receive capabilitytoa CAN controllerat• Signaling Rates(1)upto1 Mbps speedsupto1 megabits per second (Mbps).• High Input Impedance Allowsupto 120 Nodeson
Designed for operationin harsh environments, thea Bus
device features cross-wire, overvoltage and lossof• Bus Pin ESD Protection Exceeds14 kV HBM ground protection to ±36 V. Also featured are• Unpowered Node Does Not Disturb the Bus overtemperature protection as well as –7-Vto 12-V Low-Current Standby Mode: 200-µA Typical common-mode range, and toleranceto transientsof
±200V. The transceiver interfaces the single-ended• Thermal Shutdown Protection CAN controller with the differential CAN bus foundin• Glitch-Free Power-Up and Power-Down CAN Bus industrial, building automation, and automotiveProtection for Hot-Plugging applications. DeviceNet VendorID #806 Rs, pin8, selects oneof three different modesof(1) The signaling rateofa lineisthe numberof voltage operation: high-speed, slope control, or low-powertransitions thatare madeper second expressedin bps (bits mode. The high-speed modeof operationis selectedper second). by connecting pin 8 to ground, allowing the
transmitter output transistors to switch as fast as
2 Applications possible with no limitation on the rise and fall slope.
The rise and fall slope can be adjustedby connecting• CAN Data Buses resistorto groundat pin8; the slopeis proportional• Industrial Automation to the pin's output current. Slope control with an• SAE J1939 Standard Data Bus Interface external resistor valueof10 kΩ gives about 15-V/µs NMEA 2000 Standard Data Bus Interface slew rate; 100 kΩ gives about 2-V/µs slew rate.a high logic levelis appliedto the Rs pin8, the
Block Diagram device entersa low-current standby mode where the
driveris switched off and the receiver remains active.
The local protocol controller returns the deviceto the
