PM1012GP ,Low Power Precision Operational AmplifierGENERAL DESCRIPTIONPM1012 may be overcompensated, using Pin 5 to limit theThe PM1012 is a general p ..
PM105-121K , SMT POWER INDUCTORS
PM-1100 , Precision Digital Modulator/Synthesizer
PM1206 , AC Power Switch
PM1210-100J-RC , SMT Chip Inductors
PM1210-100J-RC , SMT Chip Inductors
PS324ESA , Precision, Single-Supply SPST Analog Switches
PS325CPA , Precision, Single-Supply SPST Analog Switches
PS399CSE , Precision 8-Ch, Diff. 4-Ch, 17V Analog Multiplexers
PS4009 ,PHOTO INTERRUPTERS
PS4052EPE , 17V CMOS Analog Multiplexers/Switches
PS710A-1A ,6-PIN DIP, 0.1 ohm LOW ON-STATE RESISTANCE 1.8 A CONTINUOUS LOAD CURRENT 1-ch Optical Coupled MOS FET
PM1012-PM1012GP
Low Power Precision Operational Amplifier
REV.C
Low Power Precision
Operational Amplifier
FEATURES
Low Supply Current:600mA Max
Very Low Offset:35mV Max
Low Drift:1.5mV/8C Max
Very Low Bias Current
258C: 100 pA Max
Low Noise:0.5mV p-p Typ
High Common-Mode Rejection:114 dB Min
GENERAL DESCRIPTIONThe PM1012 is a general purpose, precision operational ampli-
fier. Offering several performance enhancements over industry-
standard precision op amps such as the OP07, the PM1012
requires less than 1/6 the supply current. These enhancements
include exceptionally low bias currents of only ±80 pA, typical,
over the full military temperature range, and 132dB of com-
mon-mode rejection and power-supply rejection. The PM1012’s
low offset voltage of 35μV maximum frees the user from exter-
nal nulling in most circuits.
An open-loop gain of two million into a 10kΩ load ensures that
excellent linearity is maintained even in high gain configura-
tions, and 5 mA of output current allows 2kΩ loads to be
driven with an open-loop gain of one million. The PM1012
offers low noise, especially for a low power amplifier—onlynV/√Hz at 10 Hz. Exceptionally low current noise minimizes
PIN CONNECTIONS
Plastic Mini-DIP (P Suffix)
8-Lead SO (S Suffix)noise contributions when high source impedances are used. The
PM1012 may be overcompensated, using Pin 5 to limit the
amplifier’s bandwidth, further reducing system noise and in-
creasing stability with large capacitive loads.
The PM1012 conforms to the OP07 pinout with nulling through
Pins 1 and 8 to the positive supply. It offers an upgrade to the
OP07 in sockets where reduced power dissipation or low bias
currents are attractive. It may also be used as an upgrade from
the OP12, OP05 and 725 type op amps. The PM1012 may
replace 741 type op amps by removing the nulling potentiom-
eter, if used.
PM1012–SPECIFICATIONS
ELECTRICAL CHARACTERISTICSLong-Term
Input Offset Current
Input Bias Current
Input Noise Voltage
Input Noise Voltage Density
Common-Mode Rejection
Power-Supply Rejection
Gain Bandwidth Product
NOTESThese specifications apply for ±2 V ≤ VS ≤ ±20 V and –13.5 V ≤ VCM ≤ +13.5 V (for VS = ±15 V).10 Hz noise voltage density is sample tested. Devices 100% tested for noise are available on request.Sample tested.Guaranteed by CMR test.
Specifications subject to change without notice.
(@ VS = 615 V, VCM = 0 V, TA = +258C, unless otherwise noted)
ELECTRICAL CHARACTERISTICSNOTESThese specifications apply for ±2.5 V ≤ VS ≤ ±20 V and –13.5 V ≤ VCM ≤ +13.5 V (for VS = ±15 V).
(@ VS = 615 V, VCM = 0 V, –408C ≤ TA ≤ +858C for PM1012GP, GS, unless otherwise noted)
ABSOLUTE MAXIMUM RATINGS1Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20 V
Input Voltage2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20 V
Differential Input Voltage3 . . . . . . . . . . . . . . . . . . . . . . ±1 V
Differential Input Current3 . . . . . . . . . . . . . . . . . . . . ±10 mA
Output Short-Circuit Duration . . . . . . . . . . . . . . . . Indefinite
Operating Temperature Range
PM1012G (P, S) . . . . . . . . . . . . . . . . . . . . –40°C to +85°C
Storage Temperature Range . . . . . . . . . . . . –65°C to +150°C
Junction Temperature Range . . . . . . . . . . . . –65°C to +150°C
Lead Temperature (Soldering, 60 sec) . . . . . . . . . . . +300°C
8-Lead Plastic DIP (P)
ORDERING GUIDE
CAUTIONESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000V readily
accumulate on the human body and test equipment and can discharge without detection.
Although the PM1012 features proprietary ESD protection circuitry, permanent damage may
occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD
precautions are recommended to avoid performance degradation or loss of functionality.
NOTESAbsolute maximum ratings apply to both DICE and packaged parts, unless
otherwise noted.For supply voltages less than ±20 V, the absolute maximum input voltage is equal
to the supply voltage.The PM1012’s inputs are protected by back-to-back diodes. Current-limiting
resistors are not used in order to achieve low noise. Differential input voltages
greater than 1 V will cause excessive current to flow through the input protection
diodes unless limiting resistance is used.θJA is specified for worst case mounting conditions, i.e., θJA is specified for device
in socket for cerdip, and P-DIP packages; θJA is specified for device soldered to
printed circuit board for SO package.
PM1012C3190–2.5–2/98
PRINTED IN U.S.A.
OUTLINE DIMENSIONSDimensions shown in inches and (mm).
8-Lead Plastic DIP
(N-8)
0.430 (10.92)
0.348 (8.84)
0.280 (7.11)
0.240 (6.10)
PIN 1
SEATING
PLANE0.022 (0.558)
0.014 (0.356)
0.060 (1.52)
0.015 (0.38)0.210 (5.33)
MAX0.130
(3.30)
MIN
0.070 (1.77)
0.045 (1.15)
(2.54)
BSC
0.160 (4.06)
0.115 (2.93)
0.325 (8.25)
0.300 (7.62)
0.015 (0.381)
0.008 (0.204)
0.195 (4.95)
0.115 (2.93)
8-Lead SOIC
(SO-8)
0.1968 (5.00)
0.1890 (4.80)
0.2440 (6.20)
0.2284 (5.80)
PIN 1
0.1574 (4.00)
0.1497 (3.80)
0.0688 (1.75)
0.0532 (1.35)
SEATING
PLANE
0.0098 (0.25)
0.0040 (0.10)
0.0192 (0.49)
0.0138 (0.35)
(1.27)
BSC
0.0098 (0.25)
0.0075 (0.19)
0.0500 (1.27)
0.0160 (0.41)
0.0196 (0.50)
0.0099 (0.25)x 458
:
www.ic-phoenix.com
.