PEB2254H ,ICs for Communicationsapplications, processes and circuits implemented within components or assemblies.The information de ..
PEB2254H ,ICs for CommunicationsICs for CommunicationsFraming and Line Interface Component for PCM 30 and PCM 24FALC54PEB 2254 Adde ..
PEB2254H V1.3 ,FALC54 (Frame and Line Interface Comp...Features E1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61. ..
PEB2254HV1.3 ,FALC54 (Frame and Line Interface Comp...ICs for CommunicationsFraming and Line Interface Component for PCM 30 and PCM 24FALC54PEB 2254 Vers ..
PEB2254HV1.3 ,FALC54 (Frame and Line Interface Comp...characteristics.Terms of delivery and rights to change design reserved.For questions on technology, ..
PEB2254H-V1.3 ,FALC54 (Frame and Line Interface Comp...Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221.5 Sys ..
PIC17C42A , High-Performance 8-Bit CMOS EPROM/ROM Microcontroller
PIC18F2525-I/SO , 28/40/44-Pin Enhanced Flash Microcontrollers with 10-Bit A/D and nanoWatt Technology
PIC18F2620-I/SO , 28/40/44-Pin Enhanced Flash Microcontrollers with 10-Bit A/D and nanoWatt Technology
PIC18F2620-I/SO , 28/40/44-Pin Enhanced Flash Microcontrollers with 10-Bit A/D and nanoWatt Technology
PIC18F2620-I/SP , 28/40/44-Pin Enhanced Flash Microcontrollers with 10-Bit A/D and nanoWatt Technology
PIC18F4620-I/ML , 28/40/44-Pin Enhanced Flash Microcontrollers with 10-Bit A/D and nanoWatt Technology
PEB2254H
ICs for Communications
ICs for Communications
Framing and Line Interface Component for PCM 30 and PCM 24
FALC54
PEB 2254
Addendum / Corrections 10.97 to the Data Sheet 11.96
DS 1
Edition 10.97This edition was realized using the software system FrameMaker.
Published by Siemens AG,
HL TS,
Balanstraße 73,
81541 München Siemens AG 1997.
All Rights Reserved.
Attention please!As far as patents or other rights of third parties are concerned, liability is only assumed for components, not for
applications, processes and circuits implemented within components or assemblies.
The information describes the type of component and shall not be considered as assured characteristics.
Terms of delivery and rights to change design reserved.
For questions on technology, delivery and prices please contact the Semiconductor Group Offices in Germany or
the Siemens Companies and Representatives worldwide (see address list).
Due to technical requirements components may contain dangerous substances. For information on the types in
question please contact your nearest Siemens Office, Semiconductor Group.
Siemens AG is an approved CECC manufacturer.
PackingPlease use the recycling operators known to you. We can also help you – get in touch with your nearest sales
office. By agreement we will take packing material back, if it is sorted. You must bear the costs of transport.
For packing material that is returned to us unsorted or which we are not obliged to accept, we shall have to invoice
you for any costs incurred.
Components used in life-support devices or systems must be expressly authorized for such purpose!Critical components1 of the Semiconductor Group of Siemens AG, may only be used in life-support devices or
systems2 with the express written approval of the Semiconductor Group of Siemens AG.A critical component is a component used in a life-support device or system whose failure can reasonably be
expected to cause the failure of that life-support device or system, or to affect its safety or effectiveness of that
device or system.Life support devices or systems are intended (a) to be implanted in the human body, or (b) to support and/or
maintain and sustain human life. If they fail, it is reasonable to assume that the health of the user may be en-
Framing and Line Interface Component for PCM 30 and
PCM 24
FALC54
Addendum / Corrections 10.97 to the Data Sheet 11.96
Background to the Corruption of Received Data in the Digital Line Interface ModeThe following application information is provided to assist designers using the FALC54
family of parts.
This bulletin deals with external components connected to pin 3, REFR. Several
customers have observed “Corruption of Received Data in Digital Line Interface Mode”
as described in Errata Sheets V1.2 and V1.3.
As a result of the analysis of this problem the data corruption is eliminated by inclusion
of a small capacitor connected to pin #3. Other benefits accrue from the addition of this
external component as well.
RecommendationsInclusion of the capacitor at pin 3 is optional for existing designs using FALC54 V1.2,
V1.3, V1.3R and V1.4 with analog inputs.
Siemens recommends inclusion of the capacitor at pin #3 for all existing V1.2, V1.3,
V1.3R and V1.4 designs which use the dual rail or optical interface.
Siemens recommends inclusion of the capacitor at pin #3 for all new FALC54 designs,
regardless of input mode, because of the benefits described below.
Implementation details
FALC54 V1.2, V1.3, V1.3R and V1.4Please refer to pin #3, RFER, described on pages 13 and 152 of the Data Sheet 11.96.
1. In addition to the resistor, a capacitor should be connected as close as practical to pin
#3 of the FALC54. The other ends of these components should be connected to Vssr,
the analog ground, using short connections.
2. The capacitor should have a value between 680 and 5000 picofarads, inclusive.
3. This resistor controls a reference voltage used in the analog circuitry of the FALC54.
4. The capacitor filters the reference voltage which reduces the level sensitivity of the
analog transmit signals to variations of Vdd.
5. The capacitor improves the input jitter tolerance of the FALC54.
6. The capacitor filters noise at the digital or optical inputs, pins 2 and 4. This condition
is listed as “Corruption of Received Data in Digital Line Interface Mode” in errata sheets
This datasheet has been downloaded from:
www.ic-phoenix.com
Datasheets for electronic components.
