N74F153D ,Dual 4-line to 1-line multiplexerPIN CONFIGURATION• Non-inverting outputsEa 1 16VCC• Separate enable for each sectionS1 2 15 Eb• Com ..
N74F154D ,1-of-16 decoder/demultiplexer
N74F154D ,1-of-16 decoder/demultiplexer
N74F154D ,1-of-16 decoder/demultiplexer
N74F157AD ,Data selectors/multiplexersINTEGRATED CIRCUITS74F157*, 74F157A, 74F158*, 74F158AData selectors/multiplexers* Discontinued par ..
N74F157AN ,Data selectors/multiplexersPIN CONFIGURATIONS, 74F157A ..
NFC15-48S05 , Single and dual output 15 Watt Wide input DC/DC converters
NFC20-24S05 , Single and dual output 20 Watt Wide input DC/DC converters
NFC20-48S05 , Single and dual output 20 Watt Wide input DC/DC converters
NFC20-48S05 , Single and dual output 20 Watt Wide input DC/DC converters
NFC20-48S05 , Single and dual output 20 Watt Wide input DC/DC converters
NFC40-48S05-M , Single and triple output 40 Watt Wide input DC/DC converters
N74F153D
Dual 4-line to 1-line multiplexer
Product specification 1996 Jan 05
IC15 Data Handbook
Philips Semiconductors Product specification
74F153Dual 4-line to 1-line multiplexer
FEATURES Non-inverting outputs Separate enable for each section Common select inputs See 74F253 for 3-State version
DESCRIPTIONThe 74F153 is a dual 4-input multiplexer that can select 2 bits of
data from up to four sources selected by common Select inputs (S0,
S1). The two 4-input multiplexer circuits have individual active-Low
Enables (Ea, Eb) which can be used to strobe the outputs
independently. Outputs (Ya, Yb) are forced Low when the
corresponding Enables (Ea, Eb) are High.
The 74F153 is the logic implementation of a 2-pole, 4-position
switch where the switch is determined by the logic levels supplied to
the common select inputs.
PIN CONFIGURATION
ORDERING INFORMATION
INPUT AND OUTPUT LOADING AND FAN-OUT TABLE
NOTE: One (1.0) FAST unit load is defined as: 20μA in the High state and 0.6mA in the Low state.
LOGIC SYMBOL
IEC/IEEE SYMBOL
Philips Semiconductors Product specification
74F153Dual 4-line to 1-line multiplexer
LOGIC DIAGRAM
FUNCTION TABLEH = High voltage level
L = Low voltage level
X = Don’t care
Philips Semiconductors Product specification
74F153Dual 4-line to 1-line multiplexer
ABSOLUTE MAXIMUM RATINGS(Operation beyond the limits set forth in this table may impair the useful life of the device.
Unless otherwise noted these limits are over the operating free-air temperature range.)
RECOMMENDED OPERATING CONDITIONS
DC ELECTRICAL CHARACTERISTICS(Over recommended operating free-air temperature range unless otherwise noted.)
NOTES: For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions for the applicable type. All typical values are at VCC = 5V, Tamb = 25°C. Not more than one output should be shorted at a time. For testing IOS, the use of high-speed test apparatus and/or sample-and-hold
Philips Semiconductors Product specification
74F153Dual 4-line to 1-line multiplexer
AC ELECTRICAL CHARACTERISTICS
AC WAVEFORMSFor all waveforms, VM = 1.5V.
Waveform 1. Propagation Delay, Data to Output
Waveform 2. Propagation Delay, Enable and Select to Output
TEST CIRCUIT AND WAVEFORMS
Philips Semiconductors Product specification
74F153Dual 4-line to 1-line multiplexer
DIP16: plastic dual in-line package; 16 leads (300 mil) SOT38-4
