MPC932FA ,Low voltage PLL clock driverLOGIC DIAGRAMSD0:1PLL_EN÷4STOP Q0÷4 STOP Q1REF_CLKPLL÷5÷2200–480MHzFB_In÷6SD2MODESTOP Q2MR/OECOM_SD ..
MPC940L ,MPC940L Low Voltage 1:18 Clock Distribution ChipLOGIC DIAGRAMPECL_CLK0PECL_CLKQ01LVCMOS_CLK16Q1–Q16LVCMOS_CLK_Sel(Internal Pulldown)Q17Pinout: 32–L ..
MPC940LACR2 , LOW VOLTAGE 1:18 CLOCK DISTRIBUTION CHIP
MPC940LFA ,Low voltage 1;18 clock distribution chipLOGIC DIAGRAMPECL_CLK0PECL_CLKQ01LVCMOS_CLK16Q1–Q16LVCMOS_CLK_SelQ17Pinout: 32–Lead TQFP (Top View) ..
MPC940LFAR2 , LOW VOLTAGE 1:18 CLOCK DISTRIBUTION CHIP
MPC940LFAR2 , LOW VOLTAGE 1:18 CLOCK DISTRIBUTION CHIP
MSP430AFE253IPWR ,16-bit Ultra-Low-Power Microcontroller, 16KB Flash, 512B RAM, 3x SD24 24-TSSOP -40 to 85FEATURES• Low Supply Voltage Range: 1.8 V to 3.6 V• Up to Three 24-Bit Sigma-DeltaAnalog-to-Digital ..
MSP430F1101 ,16-Bit Ultra-Low-Power Microcontroller, 1kB Flash, 128B RAM, Comparator 20-TSSOP -40 to 85featuresa powerful 16-bit RISC CPU, 16-bit registers, and constant generators that contribute to ma ..
MSP430F1101A ,16-bit Ultra-Low-Power Microcontroller, 1kB Flash, 128B RAM, Comparatorfeaturesa powerful 16-bit RISC CPU, 16-bit registers, and constant generators that contribute to ma ..
MSP430F1101AIDGV ,16-bit Ultra-Low-Power Microcontroller, 1kB Flash, 128B RAM, Comparatorfeaturesa powerful 16-bit RISC CPU, 16-bit registers, and constant generators that contribute to ma ..
MSP430F1101AIDGVR ,16-bit Ultra-Low-Power Microcontroller, 1kB Flash, 128B RAM, ComparatorMSP430C11x1, MSP430F11x1AMIXED SIGNAL MICROCONTROLLERSLAS241I − SEPTEMBER 1999 − REVISED DECEMBER 2 ..
MSP430F1101AIDW ,16-bit Ultra-Low-Power Microcontroller, 1kB Flash, 128B RAM, ComparatorMSP430C11x1, MSP430F11x1AMIXED SIGNAL MICROCONTROLLERSLAS241I − SEPTEMBER 1999 − REVISED DECEMBER 2 ..
MPC932FA
Low voltage PLL clock driver
SEMICONDUCTOR TECHNICAL DATA- -
The MPC932 is a 3.3V compatible PLL based clock driver device
targetted for zero delay applications. The device provides 6 outputs for
driving clock loads plus a single dedicated PLL feedback clock output.
The dedicated feedback output gives the user six choices of input
multiplcation factors: x1, x1.25, x1.5, x2, x2.5 and x3. 6 Low Skew Clock Outputs 1 Dedicated PLL Feedback Output Individual Output Enable Control Fully Integrated PLL Output Frequency Up TO 120MHz 32–lead TQFP Packaging 3.3V VCC ±100ps Cycle–Cycle Jitter
The MPC932 provides individual output enable control. The enables
are synchronized to the internal clock such that upon assertion the shut
down signals will hold the clocks LOW without generating a runt pulse on
the outputs. The shut down pins provide a means of powering down
certain portions of a system or a means of disabling outputs when the full
compliment are not required for a specific design. The shut down pins will
disable the outputs when driven LOW. A common shut down pin is
provided to disable all of the outputs (except the feedback output) with a
single control signal.
Two feedback select pins are provided to select the multiplication factor of the PLL. The MPC932 provides six multiplication
factors: x1, x1.25, x1.5, x2, x2.5 and x3. In the x1.25 and x2.5 modes, the QFB output will not provide a 50% duty cycle. The
phase detector of the MPC932 only monitors rising edges of its feedback signals, thus for this function a 50% duty cycle is not
required. As the QFB signal can also be used to drive other clocks in a system it is important the user understand that the duty
cycle will not be 50%. In the x1 and x1.5 modes the QFB output will produce 50% duty cycle signals.
The MPC932 provides two pins for use in system test and debug operations. The MR/OE input will force all of the outputs into
a high impedance state to allow for back driving the outputs during system test. In addition the PLL_EN pin allows the user to
bypass the PLL and drive the outputs directly through the Ref_CLK input. Note the Ref_CLK signal will be routed through the
dividers so that it will take several transitions on the Ref_CLK input to create a transition on the outputs.
The MPC932 is fully 3.3V compatible and requires no external loop filter components. All of the inputs are LVCMOS/LVTTL
compatible and the outputs produce rail–to–rail 3.3V swings. For series terminated applications each output can drive two series
terminated 50Ω transmission lines. For parallel terminated lines the device can drive terminations of 50Ω into VCC/2. The device
is packaged in a 32–lead TQFP package to provide the optimum combination of performance, board density and cost.
