MC14584BFL1 ,Hex Schmitt Triggernoise immunity to “square up” slowly changing waveforms.• Supply Voltage Range = 3.0 Vdc to 18 VdcM ..
MC14585B ,4-Bit Magnitude ComparatorELECTRICAL CHARACTERISTICS (Voltages Referenced to V )SSÎÎÎÎÎ – 55C 25C 125CV VDD DD(4.)Vdc Min ..
MC14585BCL ,4-Bit Magnitude ComparatorELECTRICAL CHARACTERISTICS (Voltages Referenced to V )SSÎÎÎÎÎΖ 55* C 25* C 125* CV VD DD DVdc VdcC ..
MC14585BCL ,4-Bit Magnitude ComparatorBLOCK DIAGRAMSSSymbol Parameter Value Unit(A > B)4inV DC Supply Voltage – 0.5 to + 18.0 VDD6 (A = B ..
MC14585BCP ,4-Bit Magnitude Comparatorthree cascading inputs (A < B, A = B, and A > B), and three outputs (A< B, A = B, and A > B). This ..
MC14585BDR2 ,4-Bit Magnitude Comparator3MC14585B(7.)ÎÎÎÎÎ SWITCHING CHARACTERISTICS (C = 50 pF, T = 25C)L A(8.)ÎÎÎÎÎ Characteristic Symb ..
MC74ACT05DR2G , Hex Inverter with Open−Drain Outputs
MC74ACT05DTR2 ,Hex Inverter with Open-Drain OutputsMAXIMUM RATINGS*Symbol Parameter Value UnitV DC Supply Voltage (Referenced to GND) –0.5 to +7.0 VCC ..
MC74ACT05N ,Hex Inverter with Open-Drain OutputsMaximum Ratings are those values beyond which damage to the device may occur. Functional operation ..
MC74ACT08 ,Quad 2-Input AND GateMC74AC08, MC74ACT08Quad 2-Input AND Gate• Outputs Source/Sink 24 mA• ′ACT08 Has TTL Compatible Inpu ..
MC74ACT08D ,Quad 2-Input AND Gatehttp://onsemi.com3MC74AC08, MC74ACT08AC CHARACTERISTICS (For Figures and Waveforms − See Section 3 ..
MC74ACT08DR2 ,Quad 2-Input AND GateMAXIMUM RATINGSRating Symbol Value UnitDC Supply Voltage (Referenced to GND) V −0.5 to VCC+7.0PDIP− ..
MC14584BFL1
Hex Schmitt Trigger
--The MC14584B Hex Schmitt Trigger is constructed with MOS
P–channel and N–channel enhancement mode devices in a single
monolithic structure. These devices find primary use where low power
dissipation and/or high noise immunity is desired. The MC14584B
may be used in place of the MC14069UB hex inverter for enhanced
noise immunity to “square up” slowly changing waveforms. Supply Voltage Range = 3.0 Vdc to 18 Vdc Capable of Driving Two Low–power TTL Loads or One Low–power
Schottky TTL Load over the Rated Temperature Range Double Diode Protection on All Inputs Can Be Used to Replace MC14069UB For Greater Hysteresis, Use MC14106B which is Pin–for–Pin
Replacement for CD40106B and MM74Cl4
MAXIMUM RATINGS (Voltages Referenced to VSS) (Note 2.) Maximum Ratings are those values beyond which damage to the device
may occur. Temperature Derating:
Plastic “P and D/DW” Packages: – 7.0 mW/ C From 65 C To 125C
This device contains protection circuitry to guard against damage due to high
static voltages or electric fields. However, precautions must be taken to avoid
applications of any voltage higher than maximum rated voltages to this
high–impedance circuit. For proper operation, Vin and Vout should be constrained
to the range VSS (Vin or Vout) VDD.
Unused inputs must always be tied to an appropriate logic voltage level (e.g.,
either VSS or VDD). Unused outputs must be left open.
