MC14584BDR2 ,Hex Schmitt TriggerBLOCK DIAGRAM – SINGLE LINE SYSTEMthe phone line, based on a 600 Ω impedance at theReferring to the
MC14584BF ,Hex Schmitt Triggerblock diagram (Figure 1), in the standbyphone line. The 0.47 μF capacitor provides rolloffstate (ph ..
MC14584BF ,Hex Schmitt TriggerOrder this document by AN1603/D* ** * * ** ** ** * **Prepared by: Dennis MorganMotorola Analog Mar ..
MC14584BFEL ,Hex Schmitt TriggerOrder this document by AN1603/D* ** * * ** ** ** * **Prepared by: Dennis MorganMotorola Analog Mar ..
MC14584BFELG , Hex Schmitt Trigger
MC14584BFG , Hex Schmitt Trigger
MC74ACT04MEL ,Hex Inverter with LS TTL InputsMC74AC04, MC74ACT04Hex Inverter• Outputs Source/Sink 24 mA• ′ACT04 Has TTL Compatible InputsVCC
MC74ACT04N ,Hex Inverter with LS TTL InputsMAXIMUM RATINGS*Symbol Parameter Value UnitV DC Supply Voltage (Referenced to GND) –0.5 to +7.0 VCC ..
MC74ACT05 ,Hex Inverter with Open-Drain Outputshttp://onsemi.com2MC74AC05, MC74ACT05DC CHARACTERISTICS 74AC 74ACT =AVCCSymbol Parameter T = +25°C ..
MC74ACT05D ,HEX INVERTER WITH OPEN-DRAIN OUTPUTSMAXIMUM RATINGS*Symbol Parameter Value UnitV DC Supply Voltage (Referenced to GND) –0.5 to +7.0 VCC ..
MC74ACT05D ,HEX INVERTER WITH OPEN-DRAIN OUTPUTS** ** * HEX INVERTER WITHOPEN-DRAIN OUTPUTS* *The MC74AC/ACT05 is identical in pinout to the LS05. ..
MC74ACT05DR2 ,Hex Inverter with Open-Drain OutputsMC74AC05, MC74ACT05Hex Inverter withOpen-Drain OutputsThe MC74AC/ACT05 is identical in pinout to th ..
MC14584B-MC14584BD
Hex Schmitt Trigger
MC14584B
Hex Schmitt T rigger
The MC14584B Hex Schmitt Trigger is constructed with MOS
P−channel and N−channel enhancement mode devices in a single
monolithic structure. These devices find primary use where low power
dissipation and/or high noise immunity is desired. The MC14584B
may be used in place of the MC14069UB hex inverter for enhanced
noise immunity to “square up” slowly changing waveforms.
Features Supply Voltage Range = 3.0 Vdc to 18 Vdc Capable of Driving Two Low−power TTL Loads or One Low−power
Schottky TTL Load over the Rated Temperature Range Double Diode Protection on All Inputs Can Be Used to Replace MC14069UB For Greater Hysteresis, Use MC14106B which is Pin−for−Pin
Replacement for CD40106B and MM74Cl4 Pb−Free Packages are Available*
MAXIMUM RATINGS (Voltages Referenced to VSS)Maximum ratings are those values beyond which device damage can occur.
Maximum ratings applied to the device are individual stress limit values (not
normal operating conditions) and are not valid simultaneously. If these limits are
exceeded, device functional operation is not implied, damage may occur and
reliability may be affected. Temperature Derating:
Plastic “P and D/DW” Packages: – 7.0 mW/�C From 65�C To 125�C
This device contains protection circuitry to guard against damage due to high
static voltages or electric fields. However, precautions must be taken to avoid
applications of any voltage higher than maximum rated voltages to this
high−impedance circuit. For proper operation, Vin and Vout should be constrained
to the range VSS � (Vin or Vout) � VDD.
Unused inputs must always be tied to an appropriate logic voltage level (e.g.,
either VSS or VDD). Unused outputs must be left open.
