MC145484 ,5 V PCM CODEC-FILTER**Order this documentby MC145484/DSEMICONDUCTOR TECHNICAL DATA * The MC145484 is a general purpose ..
MC145484 ,5 V PCM CODEC-FILTER**Order this documentby MC145484/DSEMICONDUCTOR TECHNICAL DATA * The MC145484 is a general purpose ..
MC145484DW ,5 V PCM Codec-Filter**Order this documentby MC145484/DSEMICONDUCTOR TECHNICAL DATA**Advance Information* * DW SUFFIXTh ..
MC145484SD ,5 V PCM Codec-Filter**Order this documentby MC145484/DSEMICONDUCTOR TECHNICAL DATA**Advance Information* * DW SUFFIXTh ..
MC145484SD ,5 V PCM Codec-Filter**Order this documentby MC145484/DSEMICONDUCTOR TECHNICAL DATA**Advance Information* * DW SUFFIXTh ..
MC145488FN ,LOW-VOLTAGE CMOS OCTAL TRANSCEIVERMAXIMUM RATINGS*Symbol Parameter Value Condition UnitV DC Supply Voltage –0.5 to +7.0 VCCV DC Input ..
MC7447RX1000NB ,PPC7457RX1000NBfeatures of the MPC7457 described in the MPC7457 RISCMicroprocessor Hardware Specifications.• Power ..
MC7447-RX1000NB ,PPC7457RX1000NB Freescale Semiconductor, Inc. Advance InformationMPC7457RXNXPNSRev. 2, 10/2003MPC7457 Pa ..
MC74A5-33SNTR ,Serial Digital Temperature Sensor3MC74DETAILED OPERATING DESCRIPTIONMC74 Serial Bus ConventionsThe MC74 acquires and converts temper ..
MC74A5-50T ,Serial Digital Temperature SensorELECTRICAL CHARACTERISTICS (V = 3.3 V or 5.0V , –40°C ≤ T ≤ 125°C, unless otherwise noted.)DD ASymb ..
MC74AC00 ,QUAD 2-INPUT NAND GATEMAXIMUM RATINGS*Symbol Parameter Value UnitV DC Supply Voltage (Referenced to GND) –0.5 to +7.0 VCC ..
MC74AC00 ,QUAD 2-INPUT NAND GATE * * *QUAD 2-INPUTNAND GATE• Outputs Source/Sink 24 mA• ′ACT00 Has TTL Compatible InputsVCC14 13 12 ..
MC145484
5 V PCM CODEC-FILTER
---The MC145484 is a general purpose per channel PCM Codec–Filter with pin
selectable Mu–Law or A–Law companding, and is offered in 20–pin SOG,
SSOP, and TSSOP packages. This device performs the voice digitization and
reconstruction as well as the band limiting and smoothing required for PCM
systems. This device is designed to operate in both synchronous and
asynchronous applications and contains an on–chip precision reference
voltage.
This device has an input operational amplifier whose output is the input to the
encoder section. The encoder section immediately low–pass filters the analog
signal with an active R–C filter to eliminate very high frequency noise from being
modulated down to the passband by the switched capacitor filter. From the
active R–C filter, the analog signal is converted to a differential signal. From this
point, all analog signal processing is done differentially. This allows processing
of an analog signal that is twice the amplitude allowed by a single–ended
design, which reduces the significance of noise to both the inverted and
non–inverted signal paths. Another advantage of this differential design is that
noise injected via the power supplies is a common–mode signal that is
cancelled when the inverted and non–inverted signals are recombined. This
dramatically improves the power supply rejection ratio.
After the differential converter, a differential switched capacitor filter band–
passes the analog signal from 200 Hz to 3400 Hz before the signal is digitized
by the differential compressing A/D converter.
The decoder accepts PCM data and expands it using a differential D/A
converter. The output of the D/A is low–pass filtered at 3400 Hz and sinX/X
compensated by a differential switched capacitor filter. The signal is then filtered
by an active R–C filter to eliminate the out–of–band energy of the switched
capacitor filter.
The MC145484 PCM Codec–Filter has a high impedance VAG reference pin
which allows for decoupling of the internal circuitry that generates the
mid–supply VAG reference voltage, to the VSS power supply ground. This
reduces clock noise on the analog circuitry when external analog signals are
referenced to the power supply ground. This device is optimal for electronic
SLIC interfaces.
The MC145484 PCM Codec–Filter accepts a variety of clock formats,
including Short Frame Sync, Long Frame Sync, IDL, and GCI timing
environments. This device also maintains compatibility with Motorola’s family
of Telecommunication products, including the MC14LC5472 and MC145572
U–Interface Transceivers, MC145474/75 and MC145574 S/T–Interface Trans-
ceivers, MC145532 ADPCM Transcoder, MC145422/26 UDLT–1,
MC145421/25 UDLT–2, and MC3419/MC33120 SLICs.
The MC145484 PCM Codec–Filter utilizes CMOS due to its reliable
low–power performance and proven capability for complex analog/digital VLSI
functions. Single 5 V Power Supply Typical Power Dissipation of 15 mW, Power–Down of 0.01 mW Fully–Differential Analog Circuit Design for Lowest Noise Transmit Band–Pass and Receive Low–Pass Filters On–Chip Active R–C Pre–Filtering and Post–Filtering Mu–Law and A–Law Companding by Pin Selection On–Chip Precision Reference Voltage of 1.575 V for a – 0 dBm TLP @ 600 Ω Push–Pull 300 Ω Power Drivers with External Gain Adjust MC14LC5480EVK is the Evaluation Kit for This Device
Order this document
by MC145484/D-
SEMICONDUCTOR TECHNICAL DATA
