MC12093D ,÷2, ÷4, ÷8 1.1 GHz Low Power Prescaler with Stand-By ModeOrder this document by MC12093/D*÷** ÷** ÷* **" ** ** ** * ** *! *The MC12093 is a single modulus ..
MC12093DR2 ,÷2, ÷4, ÷8 1.1 GHz Low Power Prescaler with Stand-By ModeELECTRICAL CHARACTERISTICS (V = 2.7 to 5.5 V; T = –40 to 85°C)CC ACharacteristic Symbol Min Typ Max ..
MC12095 ,2.5 GHz Low Power Prescaler With Stand-By ModeELECTRICAL CHARACTERISTICS (V = 2.7 to 5.5 V; T = –40 to 85°C, unless otherwise noted.)CC ACharacte ..
MC12095 ,2.5 GHz Low Power Prescaler With Stand-By ModeFeaturesW = Work Week• 2.5 GHz Toggle Frequency• Supply Voltage 2.7 V to 5.5 VdcPIN CONNECTIONS• Lo ..
MC12095D ,2.5 GHz Low Power Prescaler With Stand-By ModeOrder this document by MC12095/D * ** ** * ** *The MC12095 is a single modulus prescaler for low ..
MC12095DR2 ,2.5 GHz Low Power Prescaler With Stand-By ModeMOSAIC V technology is utilized to achieve low power dissipationof 24 mW at a minimum supply volta ..
MC54F00J ,QUAD 2-INPUT NAND GATE FAST SCHOTTKY TTL
MC54F04J ,HEX INVERTER FAST SCHOTTKY TTL
MC54F08J ,QUAD 2-INPUT AND GATE FAST SCHOTTKY TTL
MC54F138J ,1-of-8 decoder/demultiplexerLOGIC DIAGRAMMC54FXXXJ CeramicE E EA A A2 1 0 1 2 3MC74FXXXN PlasticV = PIN 16CC3 2 1 MC74FXXXD SOI ..
MC54F14J ,SCHMITT TRIGGERS DUAL 4-INPUT NAND/HEX INVERTERS FAST SCHOTTKY TTL
MC54F153J ,DUAL 4-INPUT MULTIPLEXERLOGIC DIAGRAMN SUFFIXE I I I I S S I I I I E PLASTICa 0a 1a 2a 3a 1 0 0b 1b 2b 3b bCASE 648-081 3 2 ..
MC12093-MC12093D
MECL PLL COMPONENTS ?, ?, ? LOW POWER PRESCALER WITH STAND-BY MODE
Order this document by MC12093/D
ORDERING INFORMATION ÷ ÷ " ! -
The MC12093 is a single modulus prescaler for low power frequency
division of a 1.1 GHz high frequency input signal. Motorola’s advanced
MOSAIC V technology is utilized to acheive low power dissipation of
6.75 mW at a minimum supply voltage of 2.7 V.
On–chip output termination provides output current to drive a 2.0 pF
(typical) high impedance load. If additional drive is required for the prescaler
output, an external resistor can be added parallel from the OUT pin to GND
to increase the output power. Care must be taken not to exceed the
maximum allowable current through the output.
Divide ratio control inputs SW1 and SW2 select the required divide ratio of
÷2, ÷4, or ÷8.
Stand–By mode is featured to reduce current drain to 50 μA typical when
the standby pin SB is switched LOW disabling the prescaler. 1.1 GHz Toggle Frequency Supply Voltage 2.7 V to 5.5 Vdc Low Power 3.0 mA Typical Operating Temperature –40 to 85°C Divide by 2, 4 or 8 Selected by SW1 and SW2 Pins On–Chip Termination
MOSAIC V is a trademark of Motorola
FUNCTIONAL TABLE
NOTES: 1.SW1 & SW2: H = (VCC – 0.5 V) to VCC; L = Open.
2.SB: H = 2.0 V to VCC, L = GND to 0.8 V.
