MC10H330P ,Quad BUS Driver/Receiver with 2-to-1 Output MultiplexersMAXIMUM RATINGSFN SUFFIXCharacteristic Symbol Rating UnitPLCCPower Supply (V = 0) V –8.0 to 0 VdcCC ..
MC10H330P ,Quad BUS Driver/Receiver with 2-to-1 Output MultiplexersELECTRICAL CHARACTERISTICS (V = –5.2 V ±5%) (See Note)EE X Y2 23BUS BUS0° 25° 75°ZW 3 22BUSBUSChara ..
MC10H332FN ,Dual Bus Driver/Receiver
MC10H332L ,Dual Bus Driver/Receiver with 4-to-1 Output MultiplexersELECTRICAL CHARACTERISTICS (V = –5.2 V ±5%) (See Note)EE X2 Y15 160° 25° 75°X3 Y26 15Characteristic ..
MC10H334 ,Quad Bus Driver/Receiver Translator3MC10H334PACKAGE DIMENSIONSPLCC–20FN SUFFIXPLASTIC PLCC PACKAGECASE 775–02ISSUE CM S S0.007 (0.180) ..
MC10H334FN ,Quad Bus Driver/Receiver TranslatorMAXIMUM RATINGSPIN ASSIGNMENTCharacteristic Symbol Rating UnitPower Supply (V = 0) V –8.0 to 0 VdcC ..
MC4316L ,Programmable modulo-N counter(13) MOTOROLAPROGRAMMABLE MODULO-N COUNTERSThe monolithic devices are programmable, cascadable,modu ..
MC4324L ,DUAL VOLTAGE-CONTROLLED MULTIVIBRATORM04324M04024(8) MOTOROLADUAL VOLTAGE-CONTROLLED MULTIVIBRATORThe MC4324/4024 consists of two indepe ..
MC4344L ,Phase-frequency detectorLOGIC DIAGRAMPhaseFrequencyDetector#1 . 2AmplifierPhase CD 12FrequencyDetector 9#2 . 6Vcc-- Pin 14G ..
MC44002P ,CHROMA 4 VIDEO PROCESSORELECTRICAL CHARACTERISTICS (V = 5.0 Vdc, I = 70 μA, T = 25°C, unless otherwise noted.)CC 3 ACharac ..
MC44002P ,CHROMA 4 VIDEO PROCESSORfeatures include 4 selectable matrix modes (primarily forNTSC), fast beam current limiting and 16:9 ..
MC44007P ,CHROMA 4 VIDEO PROCESSORMAXIMUM RATINGS (T = 25°C, unless otherwise noted.)A 1 15 26 B-Y InputsRating Pin Symbol Value Unit ..
MC10H330L-MC10H330P
Quad BUS Driver/Receiver with 2-to-1 Output Multiplexers
SEMICONDUCTOR TECHNICAL DATA ! "
The MC10H330 is a Quad Bus Driver/Receiver with two–to–one output
multiplexers. These multiplexers have a common select and output enable.
When disabled, (OE = high) the bus outputs go to –2.0 V. Their output can be
brought to a low state (VOL) by applying a high level to the receiver enable (RE
= High). The parameters specified are with 25 Ω loading on the bus drivers and
50 Ω loads on the receivers. Propagation Delay, 1.5 ns Typical Data–to–Output Improved Noise Margin 150 mV (Over Operating Voltage and
Temperature Range) Voltage Compensated MECL 10K–Compatible
MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS (VEE = –5.2 V ±5%) (See Note)
AC PARAMETERS
DIP
PIN ASSIGNMENTVCC
XBUS
WBUS
VCC0
VCC0
YBUS
ZBUS
WIN
XIN
VEE
ZIN
YIN
VCC0
NOTE:Each MECL 10H series circuit has been designed
to meet the dc specifications shown in the test table,
after thermal equilibrium has been established. The
circuit is in a test socket or mounted on a printed
circuit board and transverse air flow greater than
500 Ifpm is maintained. Receiver outputs are
terminated through a 50–ohm resistor to –2.0 volts
dc. Bus outputs are terminated through a 25–ohm
resistor to –2.0 volts dc.
Pin assignment is for Dual–in–Line Package.
For PLCC pin assignment, see the Pin Conversion
Tables on page 6–11 of the Motorola MECL Data
Book (DL122/D).
