MC10H174L ,Dual 4 to 1 MultiplexerELECTRICAL CHARACTERISTICS (V = –5.2 V ±5%) (See Note)EELL L X0Y00° 25° 75°LL H X1Y1Characteristic ..
MC10H174MEL ,Dual 4:1 Multiplexer2AN1672/DSection 1: Translation Between Differently Supplied ECL Drivers and ReceiversTable 3. Tran ..
MC10H174MEL ,Dual 4:1 MultiplexerAN1672/DThe ECL Translator GuidePECL • LVPECL • NECL • TTL •LVTTL/LVCMOS • CMOS
MC10H174MEL ,Dual 4:1 Multiplexer
MC10H174P ,Dual 4:1 Multiplexer2MC10H174PACKAGE DIMENSIONSPLCC–20FN SUFFIXPLASTIC PLCC PACKAGECASE 775–02ISSUE CM S S0.007 (0.180) ..
MC10H175 ,Quint LatchAN1672/DThe ECL Translator GuidePECL • LVPECL • NECL • TTL •LVTTL/LVCMOS • CMOS
MC3520L ,SWITCHMODE REGULATOR CONTROL CIRCUITM03420MC3520(l?) MOTOROLA. . . . TSpecifications and ApplicationsInformation SWITCHMODE REGULATORCO ..
MC3PHAC-VDW ,3-Phase AC Motor Controllerfeatures are:• Volts-per-Hertz speed control Digital signal processing (DSP) filtering to enhance ..
MC4016L ,Programmable modulo-N counterLOGIC DIAGRAMS-tr-e' -onI L r'1-----v--,il'us12VCC = Pin16MC4317/4017Clock 1G am"=<} GND=Pin 85L DO ..
MC4016P ,Programmable modulo-N counter(13) MOTOROLAPROGRAMMABLE MODULO-N COUNTERSThe monolithic devices are programmable, cascadable,modu ..
MC4018P ,Programmable modulo-N counterLOGIC DIAGRAMS-tr-e' -onI L r'1-----v--,il'us12VCC = Pin16MC4317/4017Clock 1G am"=<} GND=Pin 85L DO ..
MC4024 ,DUAL VOLTAGE-CONTROLLED MULTIVIBRATORM04324M04024(8) MOTOROLADUAL VOLTAGE-CONTROLLED MULTIVIBRATORThe MC4324/4024 consists of two indepe ..
MC10H174L
Dual 4 to 1 Multiplexer
SEMICONDUCTOR TECHNICAL DATA -
The MC10H174 is a Dual 4–to–1 Multiplexer. This device is a functional/
pinout duplication of the standard MECL 10K part, with 100% improvement in
propagation delay and no increase in power supply current. Propagation Delay, 1.5 ns Typical Power Dissipation, 305 mW Typical Improved Noise Margin 150 mV (over operating voltage and
temperature range) Voltage Compensated MECL 10K–Compatible
MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS (VEE = –5.2 V ±5%) (See Note)
AC PARAMETERS
NOTE:Each MECL 10H series circuit has been designed to meet the dc specifications shown in the test table,
after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed
circuit board and transverse air flow greater than 500 Iinear fpm is maintained. Outputs are terminated
through a 50–ohm resistor to –2.0 volts.
DIP
PIN ASSIGNMENTVCC1
DO0
DO2
DO1
DO3
VEE
VCC2
ENABLE
D10
D12
D11
D13
Pin assignment is for Dual–in–Line Package.
For PLCC pin assignment, see the Pin Conversion
Tables on page 6–11 of the Motorola MECL Data
Book (DL122/D).