MC10H131L ,Dual D Type Master-Slave Flip-FlopMAXIMUM RATINGSCharacteristic Symbol Rating UnitPower Supply (V = 0) V –8.0 to 0 VdcCC EE
MC10H131L. ,Dual D Type Master-Slave Flip-Flop**SEMICONDUCTOR TECHNICAL DATA* * * **The MC10H131 is a MECL 10H part which is a functional/pinout ..
MC10H131M ,Dual Type D Master-Slave Flip-Flop3AND8090/DAC Test BoardsAn example of an AC characteristic test board is shown inEach test device i ..
MC10H131MEL ,Dual Type D Master-Slave Flip-FlopPrepared by: Paul ShockmanON SemiconductorAPPLICATION NOTEObjectiveGeneral BackgroundThis applicati ..
MC10H131MEL ,Dual Type D Master-Slave Flip-Flop
MC10H131ML2 ,Dual D Type Master-Slave Flip-FlopLOGIC DIAGRAMInput Voltage (V = 0) V 0 to V VdcCC I EES1 5Output Current — Continuous I 50 mAout— ..
MC34268DT ,800mA, 2.85, SCSI-2 Active Terminator, Low Dropout Voltage RegulatorThermal CharacteristicsDT Suffix, Plastic Package, Case 369AT = 25°C, Derate Above T = 25°C P Inter ..
MC34268DTRK ,800mA, 2.85, SCSI-2 Active Terminator, Low Dropout Voltage Regulatorcircuits. This device offers the circuit designer an economicalMARKINGsolution for precision voltag ..
MC34280FTB ,Power Supply & Management IC for Handheld Electronic ProductsBlock DiagramBatteryLockCVDDSwitchc = 20uVBAT VBATOptionalCMAINbGNDc = 100pRiref CporRenr = 480 k c ..
MC34280FTB ,Power Supply & Management IC for Handheld Electronic ProductsFEATURES:PIN CONNECTIONS• Low Input Voltage, 1V up• Low Quiescent Current in Standby Mode: 35μA typ ..
MC34280FTBR2 ,Power Supply & Management IC for Handheld Electronic Productsfunctions. Both regulators apply Pulse–Frequency–Modulation(PFM). The main step–up regulator output ..
MC3446N , QUADRUPLE BUS TRANSCEIVER
MC10H131FN-MC10H131L-MC10H131L.-MC10H131P
Dual D Type Master-Slave Flip-Flop
SEMICONDUCTOR TECHNICAL DATA - -
The MC10H131 is a MECL 10H part which is a functional/pinout duplication
of the standard MECL 10K family part, with 100% improvement in clock speed
and propagation delay and no increase in power–supply current. Propagation Delay, 1.0 ns Typical Power Dissipation, 235 mW Typical Improved Noise Margin 150 mV (Over Operating Voltage and
Temperature Range) Voltage Compensated MECL 10K–Compatible
MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS (VEE = –5.2 V ±5%) (See Note)
AC PARAMETERS
NOTE:Each MECL 10H series circuit has been designed to meet the dc specifications shown in the test table,
after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit
board and transverse air flow greater than 500 Iinear fpm is maintained. Outputs are terminated through
a 50–ohm resistor to –2.0 volts.
DIP
PIN ASSIGNMENTVCC1
CE1
VEE
VCC2
CE2
Pin assignment is for Dual–in–Line Package.
For PLCC pin assignment, see the Pin Conversion
