MC10123P ,Triple 4-3-3-Input Bus DriverLOGIC DIAGRAMDIP4PIN ASSIGNMENT5367 V 1 16 VCC1 CC29B C2 15OUT OUT10 211A C3 14OUT IN12CA 4 13ININ1 ..
MC10124 ,Quad TTL to MECL Translator**SEMICONDUCTOR TECHNICAL DATA* ** * **The MC10124 is a quad translator for interfacing data and c ..
MC10124 ,Quad TTL to MECL TranslatorELECTRICAL CHARACTERISTICSTest LimitsPi Pin–30°C +25°C +85°CUnder UnderCharacteristic Symbol Test U ..
MC10124FN ,Quad TTL to MECL TranslatorLOGIC DIAGRAMB D3 14OUT OUTDA 4 13OUTOUT54CA 5 12OUTIN62COMMOND6 11INSTROBE73B C7 10IN IN1VV 8 9CCE ..
MC10124L ,Quad TTL to MECL TranslatorLOGIC DIAGRAMB D3 14OUT OUTDA 4 13OUTOUT54CA 5 12OUTIN62COMMOND6 11INSTROBE73B C7 10IN IN1VV 8 9CCE ..
MC10124P ,Quad TTL to MECL TranslatorLOGIC DIAGRAMB D3 14OUT OUTDA 4 13OUTOUT54CA 5 12OUTIN62COMMOND6 11INSTROBE73B C7 10IN IN1VV 8 9CCE ..
MC33291DW ,Eight Output Switch with Serial Peripheral Interface I/OFeatures:CASE 751E• Designed to Operate Over Wide Supply Voltages of 5.5 to 26.5 V SOICW (16+4+4)• ..
MC33291DWR2 ,Eight Output Switch with Serial Peripheral Interface I/Ofeatures include: VeryLow Standby Current, SPI Cascade Fault Reporting Capability, Internal 53 VCla ..
MC33298DW ,OCTAL SERIAL SWITCH (SPI Input/Output)MAXIMUM RATINGS (All voltages are with respect to ground, unless otherwise noted.)Rating Symbol Va ..
MC33304DR2 ,Low Voltage Rail-to-Rail, Sleepmode Operational AmplifierELECTRICAL CHARACTERISTICS (V = +6.0 V, V = –6.0 V, R = 600 Ω, T = 25°C, unless otherwise noted.)C ..
MC33340 ,Battery Fast Charge Controllerfeatures include battery over and undervoltagedetection, latched over temperature detection, and po ..
MC33340P ,Battery Fast Charge ControllerELECTRICAL CHARACTERISTICS (V = 6.0 V, for typical values T = 25°C, for min/max values T is the op ..
MC10123L-MC10123P
Triple 4-3-3-Input Bus Driver
SEMICONDUCTOR TECHNICAL DATA -
The MC10123 consists of three NOR gates designed for bus driving
applications on card or between cards. Output low logic levels are specified with
VOL = –2.1 Vdc so that the bus may be terminated to –2.0 Vdc. The gate output,
when low, appears as a high impedance to the bus, because the output emitter–
followers of the MC10123 are “turned–off.” This eliminates discontinuities in the
characteristic impedance of the bus.
The VOH level is specified when driving a 25–ohm load terminated to –2.0
Vdc, the equivalent of a 50–ohm bus terminated at both ends. Although 25
ohms is the lowest characteristic impedance that can be driven by the
MC10123, higher impedance values may be used with this part. A typical
50–ohm bus is shown in Figure 1. = 310 mW typ/pkg (No Load)
tpd = 3.0 ns typ
tr, tf = 2.5 ns typ (20%–80%)
LOGIC DIAGRAMVCC1 = PIN 1
VCC2 = PIN 16
VEE = PIN 8 15 2 36
FIGURE 1 — 50–OHM BUS DRIVER (TYPICAL APPLICATION)1/3 MC10123 1/3 MC10123 1/3 MC10123
ZO = 50 Ω
VDC
RECEIVERS (MECL GATES) –2.0
VDC
50 Ω50 Ω
DIP
PIN ASSIGNMENTVCC1
BOUT
AOUT
AIN
AIN
AIN
AIN
VEE
VCC2
COUT
CIN
CIN
CIN
BIN
BIN
BIN
Pin assignment is for Dual–in–Line Package.
For PLCC pin assignment, see the Pin Conversion
Tables on page 6–11 of the Motorola MECL Data
Book (DL122/D).
