MAX9015AEKA ,SOT23, Dual, Precision, 1.8V, Nanopower Comparators With/Without ReferenceElectrical Characteristics—MAX9015–MAX9018 (Single and Duals with REF)(V = 5V, V = 0V, V = V , T = ..
MAX9015AEKA+ ,SOT23, Dual, Precision, 1.8V, Nanopower Comparators With/Without ReferenceApplicationsMAX9016AEKA-T -40°C to +85°C 8 SOT23 AEIX2-Cell Battery Window DetectorsMAX9017AEKA-T - ..
MAX9017AEKA-T ,SOT23 / Dual / Precision / 1.8V / Nanopower Comparators With/Without ReferenceELECTRICAL CHARACTERISTICS—MAX9015–MAX9018 (Single and Duals with REF)(V = 5V, V = 0V, V = V , T = ..
MAX9018AEKA ,PLASTIC ENCAPSULATED DEVICES MAX9018AEKA Rev. A RELIABILITY REPORT FOR MAX9018AEKA PLASTIC EN ..
MAX9019EKA-T ,SOT23 / Dual / Precision / 1.8V / Nanopower Comparators With/Without ReferenceApplicationsMAX9017AEKA-T -40°C to +85°C 8 SOT23-8 AEIQ2-Cell Battery Window DetectorsMAX9017BEKA-T ..
MAX901ACPE ,High-speed, low-power voltage comparatorFeatures
Ordering Information
TEMP. RANGE
JC to +70'C
O'C to +70'C
O'C to +70'C
JC to +70 ..
MB88101A ,A/D Converter (With 4-channel Input at 12-bit Resolution)FEATURES• 4-channel analog input• One analog input channel selectable for conversion by external co ..
MB88101A ,A/D Converter (With 4-channel Input at 12-bit Resolution)FUJITSU SEMICONDUCTORDS04-13105-2EDATA SHEETLinear IC ConverterCMOSA/D Converter(With 4-channel I ..
MB88101APF ,A/D Converter (With 4-channel Input at 12-bit Resolution)FEATURES• 4-channel analog input• One analog input channel selectable for conversion by external co ..
MB88141 ,D/A Converter for Digital Tuning (With Built-in OP Amp and I/O Expander)FUJITSU SEMICONDUCTORDS04-13211-3EDATA SHEETGeneral Purpose Linear IC’s General Purpose ConvertersC ..
MB88141A ,D/A Converter for Digital Tuning (Compatible with I 2 C Bus)FUJITSU SEMICONDUCTORDS04-13213-1EDATA SHEETLinear IC ConverterCMOSD/A Converter for Digital Tuning ..
MB88141APF ,D/A Converter for Digital Tuning (Compatible with I2C Bus)FUJITSU SEMICONDUCTORDS04-13213-1EDATA SHEETLinear IC ConverterCMOSD/A Converter for Digital Tuning ..
MAX9015AEKA-MAX9015AEKA+
SOT23, Dual, Precision, 1.8V, Nanopower Comparators With/Without Reference
MAX9015–MAX9020SOT23, Dual, Precision, 1.8V,
Nanopower Comparators
With/Without Reference
General DescriptionThe single MAX9015/MAX9016 and dual MAX9017–
MAX9020 nanopower comparators in space-saving
SOT23 packages feature Beyond-the-Rails™ inputs
and are guaranteed to operate down to 1.8V. The A-
grade packages feature an on-board 1.236V ±1% ref-
erence, while the B-grade packages feature a 1.24V
±1.75% reference. An ultra-low supply current of 0.85µA
(MAX9019/MAX9020), 1µA (MAX9015/MAX9016),or
1.2µA (MAX9017/MAX9018) makes the MAX9015–
MAX9020 family of comparators ideal for all 2-cell bat-
tery monitoring/management applications.
The unique design of the MAX9015–MAX9020 output
stage limits supply-current surges while switching,
which virtually eliminates the supply glitches typical of
many other comparators. This design also minimizes
overall power consumption under dynamic conditions.
The MAX9015/MAX9017/MAX9019 have a push-pull
output stage that sinks and sources current. Large
internal output drivers allow rail-to-rail output swing with
loads up to 6mA. The MAX9016/MAX9018/MAX9020
have an open-drain outputstage that makes them suit-
able for mixed-voltage system design. All devices are
available in the ultra-small 8-pin SOT23 package.
Refer to the MAX9117–MAX9120 data sheet for similar
single comparators with or without reference in a tiny
SC70 package.
Applications
FeaturesUltra-Low Total Supply Current
0.85µA (MAX9019/MAX9020)
1.0µA (MAX9015A/MAX9016A)
1.2µA (MAX9017/MAX9018)
Guaranteed Operation Down to 1.8V
Precision VOS< 5mV (max)
Internal 1.236V ±1% Reference (A Grade)
Input Voltage Range Extends 200mV
Beyond-the-Rails
CMOS Push-Pull Output with ±6mA Drive Capability
(MAX9015/MAX9017/MAX9019)
Open-Drain Output Versions Available
(MAX9016/MAX9018/MAX9020)
Crowbar-Current-Free Switching
Internal 4mV Hysteresis for Clean Switching
No Phase Reversal for Overdriven Inputs
Dual Versions in Space-Saving 8-Pin SOT23
Package
Ordering Information
Ordering Information continued at end of data sheet.
Pin Configurations appear at end of data sheet.Beyond-the-Rails is a trademark of Maxim Integrated Products, Inc.
T = Tape and reel.
/V denotes an automotive qualified part.
PARTTEMP RANGEPIN-
PACKAGE
TOP
MARK
MAX9015AEKA-T-40°C to +85°C8 SOT23AEIW
MAX9015AEKA/V+T-40°C to +85°C8 SOT23+AETV
MAX9016AEKA-T-40°C to +85°C8 SOT23AEIX
MAX9017AEKA-T-40°C to +85°C8 SOT23AEIQ
MAX9017BEKA-T-40°C to +85°C8 SOT23AEIS
Selector Guide
PARTCOMPARATOR(S)INTERNAL REFERENCE (V)OUTPUT TYPESUPPLY CURRENT (µA)MAX9015A11.236 ±1%Push-pull1
MAX9016A11.236 ±1%Open drain1
MAX9017A21.236 ±1%Push-pull1.2
MAX9017B21.240 ±1.75%Push-pull1.2
MAX9018A21.236 ±1%Open drain1.2
MAX9018B21.240 ±1.75%Open drain1.2
MAX90192—Push-pull0.85
MAX90202—Open drain0.85
2-Cell Battery
Monitoring/Management
Ultra-Low Power Systems
Mobile Communications
Notebooks and PDAs
Threshold Detectors/
Discriminators
Window Detectors
Sensing at Ground or
Supply Line
Telemetry and Remote
Systems
Medical Instruments
MAX9015–MAX9020SOT23, Dual, Precision, 1.8V,
Nanopower Comparators
With/Without Reference
Absolute Maximum Ratings
Electrical Characteristics—MAX9015–MAX9018 (Single and Duals with REF)(VCC= 5V, VEE= 0V, VIN-= VREF, TA= -40°C to +85°C, unless otherwise noted. Typical values are at TA= +25°C.) (Note 1)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
Supply Voltage (VCCto VEE)....................................................6V
IN+, IN-, INA+, INB+, INA-, INB-,
REF/INA-, REF..................................(VEE- 0.3V) to (VCC+ 0.3V)
Output Voltage (OUT_)
MAX9015A, MAX9017_, MAX9019....(VEE- 0.3V) to (VCC+ 0.3V)
MAX9016A, MAX9018_, MAX9020...................(VEE- 0.3V) to +6V
Output Current (REF, OUT_, REF/INA-)............................±50mA
Output Short-Circuit Duration (REF, OUT_, REF/INA-)...........10s
Continuous Power Dissipation (TA= +70°C)
8-Pin SOT23 (derate 9.1mW/°C above +70°C)............727mW
Operating Temperature Range...........................-40°C to +85°C
Storage Temperature Range.............................-65°C to +150°C
Junction Temperature......................................................+150°C
Lead Temperature (soldering, 10s).................................+300°C
Soldering Temperature (reflow).......................................+260°C
PARAMETERSYMBOLCONDITIONSMINTYPMAXUNITS Supply Voltage Range VCCInferred from the PSRR test 1.8 5.5 V
VCC = 1.8V, TA = +25°C 1.0 1.5
VCC = 5.0V, TA = +25°C 1.1 1.7 MAX9015A/
MAX9016A VCC = 5.0V,
TA = TMIN to TMAX 2.0
VCC = 1.8V, TA = +25°C 1.2 1.9
VCC = 5.0V, TA = +25°C 1.4 2.3
Supply Current ICC
MAX9017_/
MAX9018_ VCC = 5.0V,
TA = TMIN to TMAX 2.8
µA
Input Common-Mode
Voltage Range
(MAX9015A/MAX9016A)
VCM Inferred from VOS test VEE - 0.2 VCC + 0.2 V
IN+ Voltage Range
(MAX9017_/MAX9018_) VIN+ Inferred from the output swing test VEE - 0.2 VCC + 0.2 V
TA = +25°C 0.15 5 Input Offset Voltage VOS VEE - 0.2V < VCM <
VCC + 0.2V (Note 2) TA = TMIN to TMAX 10 mV
Input-Referred Hysteresis VHB VEE - 0.2V < VCM < VCC + 0.2V (Note 3) 4 mV
TA = +25°C ±0.15 ±1 Input Bias Current (IN+,
IN-, INA+, INB+, INB-) IBTA = TMIN to TMAX ±2 nA
Power-Supply Rejection
Ratio PSRR VCC = 1.8V to 5.5V 0.1 1 mV/V
TA = +25°C 100 200 VCC = 1.8V,
ISOURCE = 1mA TA = TMIN to TMAX 300
TA = +25°C 250 350
Output Voltage Swing High
(MAX9015A/MAX9017_) VCC - VOH
VCC = 5.0V,
ISOURCE = 6mA TA = TMIN to TMAX 450
mV
TA = +25°C 105 200 VCC = 1.8V,
ISINK = 1mA TA = TMIN to TMAX 300
TA = +25°C 285 350
Output Voltage Swing Low
(MAX9015A/MAX9016A/
MAX9017_/MAX9018_)
VOL
VCC = 5.0V,
ISINK = 6mA TA = TMIN to TMAX 450
mV
MAX9015–MAX9020SOT23, Dual, Precision, 1.8V,
Nanopower Comparators
With/Without Reference
Electrical Characteristics—MAX9015–MAX9018 (Single and Duals with REF)
(continued)(VCC= 5V, VEE= 0V, VIN-= VREF, TA= -40°C to +85°C, unless otherwise noted. Typical values are at TA= +25°C.) (Note 1)
PARAMETERSYMBOLCONDITIONSMINTYPMAXUNITS Output Leakage Current
(MAX9016A/MAX9018_) ILEAK VCC = 5.5V, VOUT = 5.5V 0.001 1 µA
VCC = 1.8V 3 Sourcing, VOUT =
VEE (MAX9015A/
MAX9017_ only) VCC = 5.0V 35
VCC = 1.8V 3
Output Short-Circuit Current ISC
Sinking,
VOUT = VCC VCC = 5.0V 33
mA
VCC = 1.8V 7 High-to-Low Propagation
Delay (Note 4) tPD- VCC = 5.0V 6 µs
MAX9015A/MAX9017_ 11
VCC = 1.8V MAX9016A/MAX9018_,
RPULLUP = 100k to VCC 12
MAX9015A/MAX9017_ 28
Low-to-High Propagation
Delay (Note 4) tPD+
VCC = 5.0V MAX9016A/MAX9018_,
RPULLUP = 100k to VCC 31
µs
Rise Time tRISE CL = 15pF (MAX9015A/MAX9017_) 1.6 µs
Fall Time tFALL CL = 15pF 0.2 µs
Power-Up Time tON 1.2 ms
TA = +25°C, 1.0% 1.224 1.236 1.248 MAX901_A TA = TMIN to TMAX, 2.5% 1.205 1.267
TA = +25°C, 1.75% 1.218 1.240 1.262
Reference Voltage
(Note 5) VREF
MAX901_B TA = TMIN to TMAX, 4.5% 1.184 1.296
Reference Voltage
Temperature Coefficient TCREF 40 ppm/°C
BW = 10Hz to 1kHz, CREF = 1nF 29 Reference Output Voltage
Noise ENBW = 10Hz to 6kHz, CREF = 1nF 60 µVRMS
Reference Line Regulation VREF/
VCC1.8V VCC 5.5V 0.5 mV/V
Reference Load
Regulation
VREF/
IOUTIOUT = 0 to 100nA 0.03 mV/nA
MAX9015–MAX9020SOT23, Dual, Precision, 1.8V,
Nanopower Comparators
With/Without Reference
Electrical Characteristics—MAX9019/MAX9020 (Duals without REF)(VCC= 5V, VEE= 0V, TA= -40°C to +85°C, unless otherwise noted. Typical values are at TA= +25°C.) (Note 1)
PARAMETERSYMBOLCONDITIONSMINTYPMAXUNITS Supply Voltage Range VCCInferred from the PSRR test 1.8 5.5 V
VCC = 1.8V, TA = +25°C 0.85 1.50
VCC = 5.0V, TA = +25°C 1.1 1.70 Supply Current ICC MAX9019/
MAX9020 VCC = 5.0V,
TA = TMIN to TMAX 2.0
µA
Input Common-Mode
Voltage Range VCM Inferred from VOS test VEE - 0.2 VCC + 0.2 V
TA = +25°C 1 5 Input Offset Voltage VOS VEE - 0.2V < VCM <
VCC + 0.2V (Note 2) TA = TMIN to TMAX 10 mV
Input-Referred Hysteresis VHB VEE - 0.2V < VCM < VCC + 0.2V (Note 3) 4 mV
TA = +25°C 0.15 1 Input Bias Current
(INA-, INA+, INB+, INB-) IBTA = TMIN to TMAX 2 nA
Power-Supply Rejection Ratio PSRR VCC = 1.8V to 5.5V 0.1 1 mV/V
TA = +25°C 55 200 VCC = 1.8V,
ISOURCE = 1mA TA = TMIN to TMAX 300
TA = +25°C 190 350
Output Voltage Swing High
(MAX9019 Only) VCC - VOH
VCC = 5.0V,
ISOURCE = 6mA TA = TMIN to TMAX 450
mV
TA = +25°C 55 200 VCC = 1.8V,
ISINK = 1mA TA = TMIN to TMAX 300
TA = +25°C 190 350 Output Voltage Swing Low VOL
VCC = 5.0V,
ISINK = 6mA TA = TMIN to TMAX 450
mV
Output Leakage Current
(MAX9020 Only) ILEAK VCC = 5.5V, VOUT = 5.5V 0.001 1 µA
VCC = 1.8V 3 Sourcing, VOUT =
VEE (MAX9019 only) VCC = 5.0V 35
VCC = 1.8V 3 Output Short-Circuit Current ISC
Sinking, VOUT = VCC VCC = 5.0V 33
mA
VCC = 1.8V 7 High-to-Low Propagation
Delay (Note 4) tPD- VCC = 5.0V 6 µs
MAX9019 11
VCC = 1.8V MAX9020, RPULLUP =
100k to VCC 12
MAX9019 28
Low-to-High Propagation
Delay (Note 4) tPD+
VCC = 5.0V MAX9020, RPULLUP =
100k to VCC 31
µs
MAX9015–MAX9020SOT23, Dual, Precision, 1.8V,
Nanopower Comparators
With/Without Reference
-Note 1:All devices are 100% tested at TA= +25°C. Specifications over temperature (TA= TMINto TMAX) are guaranteed by design,
not production tested.
Note 2:VOSis defined as the center of the hysteresis band at the input.
Note 3:The hysteresis-related trip points are defined as the edges of the hysteresis band, measured with respect to the center of
the band (i.e., VOS) (Figure 1).
Note 4:Specified with an input overdrive (VOVERDRIVE) of 100mV, and a load capacitance of CL= 15pF. VOVERDRIVEis defined
above and beyond the offset voltage and hysteresis of the comparator input.
Note 5:High current traces should not be routed in the vicinity of or below MAX9018. There is a chance of voltage reference being
overloaded resulting in drop of output voltage.
Electrical Characteristics—MAX9019/MAX9020 (Duals without REF) (continued)(VCC= 5V, VEE= 0V, TA= -40°C to +85°C, unless otherwise noted. Typical values are at TA= +25°C.) (Note 1)
PARAMETERSYMBOLCONDITIONSMINTYPMAXUNITS Rise Time tRISE CL = 15pF (MAX9019 only) 1.6 µs
Fall Time tFALL CL = 15pF 0.2 µs
Power-Up Time tON 1.2 ms
Typical Operating Characteristics(VCC= 5V, VEE= 0V, CL= 15pF, VOVERDRIVE= 100mV, TA= +25°C, unless otherwise noted.)
MAX9015/MAX9016
SUPPLY CURRENT
vs. SUPPLY VOLTAGE AND TEMPERATURE
MAX9015 toc01
SUPPLY VOLTAGE (V)
SUPPLY CURRENT (
TA = +85°C
TA = +25°C
TA = -40°C
MAX9017/MAX9018
SUPPLY CURRENT
vs. SUPPLY VOLTAGE AND TEMPERATURE
MAX9015 toc02
SUPPLY VOLTAGE (V)
SUPPLY CURRENT (
TA = +85°C
TA = +25°C
TA = -40°C
MAX9019/MAX9020
SUPPLY CURRENT
vs. SUPPLY VOLTAGE AND TEMPERATURE
MAX9015 toc03
SUPPLY VOLTAGE (V)
SUPPLY CURRENT (
TA = +85°C
TA = +25°C
TA = -40°C
MAX9015/MAX9016
SUPPLY CURRENT vs. TEMPERATURE
MAX9015 toc04
TEMPERATURE (°C)
SUPPLY CURRENT (
VCC = 3V
VCC = 1.8V
VCC = 5V
MAX9017/MAX9018
SUPPLY CURRENT vs. TEMPERATURE
MAX9015 toc05
TEMPERATURE (°C)
SUPPLY CURRENT (
VCC = 3V
VCC = 1.8V
VCC = 5V
MAX9019/MAX9020
SUPPLY CURRENT vs. TEMPERATURE
MAX9015 toc06
TEMPERATURE (°C)
SUPPLY CURRENT (
VCC = 3V
VCC = 1.8V
VCC = 5V
MAX9015–MAX9020SOT23, Dual, Precision, 1.8V,
Nanopower Comparators
With/Without Reference
Typical Operating Characteristics (continued)(VCC= 5V, VEE= 0V, CL= 15pF, VOVERDRIVE= 100mV, TA= +25°C, unless otherwise noted.)101001k10k100k
MAX9015/MAX9016
SUPPLY CURRENT
vs. OUTPUT TRANSITION FREQUENCYMAX9015 toc07
OUTPUT TRANSITION FREQUENCY (Hz)
SUPPLY CURRENT (
VCC = 3V
VCC = 1.8V
VCC = 5V101001k10k100k
MAX9017/MAX9018
SUPPLY CURRENT
vs. OUTPUT TRANSITION FREQUENCYMAX9015 toc08
OUTPUT TRANSITION FREQUENCY (Hz)
SUPPLY CURRENT (
VCC = 3V
VCC = 1.8V
VCC = 5V101001k10k100k
MAX9019/MAX9020
SUPPLY CURRENT
vs. OUTPUT TRANSITION FREQUENCYMAX9015 toc09
OUTPUT TRANSITION FREQUENCY (Hz)
SUPPLY CURRENT (
VCC = 3V
VCC = 1.8V
VCC = 5V
OUTPUT VOLTAGE LOW
vs. SINK CURRENT
MAX9015 toc10
SINK CURRENT (mA)
(mV)
VCC = 3V
VCC = 1.8V
VCC = 5V
OUTPUT VOLTAGE LOW
vs. SINK CURRENT AND TEMPERATURE
MAX9015 toc11
SINK CURRENT (mA)
(mV)TA = +85°C
TA = -40°C
TA = +25°C
OUTPUT VOLTAGE HIGH
vs. SOURCE CURRENT
MAX9015 toc12
SOURCE CURRENT (mA)
CC
- V
(V)
VCC = 3V
VCC = 1.8V
VCC = 5V
OUTPUT VOLTAGE HIGH
vs. SOURCE CURRENT AND TEMPERATURE
MAX9015 toc13
SOURCE CURRENT (mA)
CC
- V
(V)
TA = +85°C
TA = -40°C
TA = +25°C
SHORT-CIRCUIT TO VCC (SINK CURRENT)
vs. TEMPERATURE
MAX9015 toc14
TEMPERATURE (°C)
SINK CURRENT (mA)
VCC = 3V
VCC = 1.8V
VCC = 5V
SHORT-CIRCUIT TO GND
(SOURCE CURRENT) vs.TEMPERATURE
MAX9015toc15
TEMPERATURE (°C)
SINK CURRENT (mA)VCC = 3V
VCC = 1.8V
VCC = 5V
MAX9015–MAX9020SOT23, Dual, Precision, 1.8V,
Nanopower Comparators
With/Without Reference
INPUT OFFSET VOLTAGE DISTRIBUTIONMAX9015 toc16
VOS (mV)
PERCENTAGE OF UNITS (%)
OFFSET VOLTAGE vs. TEMPERATURE
MAX9015 toc17
TEMPERATURE (°C)
(mV)3510-15
VCC = 1.8V
VCC = 5V
REFERENCE VOLTAGE DISTRIBUTIONMAX9015 toc18
VREF (V)
PERCENTAGE OF UNITS (%)
A GRADE
HYSTERESIS VOLTAGE
vs. TEMPERATUREMAX9015 toc19
TEMPERATURE (°C)
(mV)3510-15
REFERENCE VOLTAGE
vs. TEMPERATURE
MAX9015 toc20
TEMPERATURE (°C)
REFERENCE VOLTAGE (V)
VCC = 3V
VCC = 1.8V
VCC = 5V
A GRADE
REFERENCE VOLTAGE
vs. SUPPLY VOLTAGE
MAX9015 toc21
SUPPLY VOLTAGE (V)
REFERENCE VOLTAGE (V)
REFERENCE VOLTAGE
vs. REFERENCE SOURCE CURRENT
MAX9015 toc22
REFERENCE SOURCE CURRENT (nA)
REFERENCE VOLTAGE (V)
VCC = 1.8V
VCC = 5V
VCC = 3V
REFERENCE VOLTAGE
vs. REFERENCE SINK CURRENT
MAX9015 toc23
REFERENCE SINK CURRENT (nA)
REFERENCE VOLTAGE (V)
VCC = 1.8V
VCC = 5V
VCC = 3V
REFERENCE VOLTAGE vs. REFERENCE
SINK CURRENT AND TEMPERATURE
MAX9015 toc24
REFERENCE SINK CURRENT (nA)
REFERENCE VOLTAGE (V)
VCC = 3VTA = +85°C
TA = +25°C
TA = -40°C
Typical Operating Characteristics (continued)(VCC= 5V, VEE= 0V, CL= 15pF, VOVERDRIVE= 100mV, TA= +25°C, unless otherwise noted.)
MAX9015–MAX9020SOT23, Dual, Precision, 1.8V,
Nanopower Comparators
With/Without Reference
INPUT BIAS CURRENT
vs. INPUT BIAS VOLTAGE
MAX9015 toc25
INPUT BIAS VOLTAGE (IN-) (V)
INPUT BIAS CURRENT (IN-) (nA)
IN+ = 2.5V
PROPAGATION DELAY (tPD-)
vs. TEMPERATURE
MAX9015 toc26
TEMPERATURE (°C)
tPD- VCC = 1.8V
VCC = 5V
VCC = 3V
PROPAGATION DELAY (tPD+)
vs. TEMPERATURE
MAX9015 toc27
TEMPERATURE (°C)
PD+
VCC = 5V
VCC = 3V
VCC = 1.8V
PROPAGATION DELAY (tPD-)
vs. CAPACITIVE LOAD
MAX9015 toc28
CAPACITIVE LOAD (nF)
tPD-
VCC = 1.8V
VCC = 3V
VCC = 5V
PROPAGATION DELAY (tPD+)
vs. CAPACITIVE LOAD
MAX9015 toc29
CAPACITIVE LOAD (nF)
tPD+
VCC = 1.8V
VCC = 3V
VCC = 5V20304050
PROPAGATION DELAY (tPD-)
vs. INPUT OVERDRIVE MAX9015 toc30
INPUT OVERDRIVE (mV)
tPD-
VCC = 1.8V
VCC = 5V
VCC = 3V
PROPAGATION DELAY (tPD+)
vs. INPUT OVERDRIVE
MAX9015 toc31
tPD+
VCC = 5V
VCC = 3V
VCC = 1.8V
10k10M1M100k
PROPAGATION DELAY (tPD-)
vs. PULLUP RESISTANCEMAX9015 toc32
tPD-
VCC = 1.8V
VCC = 3V
VCC = 5V
10k10M1M100k
PROPAGATION DELAY (tPD+)
vs. PULLUP RESISTANCEMAX9015 toc33
tPD+
VCC = 5V
VCC = 3V
VCC = 1.8V
Typical Operating Characteristics (continued)(VCC= 5V, VEE= 0V, CL= 15pF, VOVERDRIVE= 100mV, TA= +25°C, unless otherwise noted.)
MAX9015–MAX9020SOT23, Dual, Precision, 1.8V,
Nanopower Comparators
With/Without Reference
PROPAGATION DELAY (tPD-) (VCC = 5V)MAX9015 toc34
2μs/div
VOUT
2V/div
VIN+
50mV/div
PROPAGATION DELAY (tPD+) (VCC = 5V)MAX9015 toc35
10μs/div
VOUT
2V/div
VIN+
50mV/div
PROPAGATION DELAY (tPD-) (VCC = 3V)MAX9015 toc36
2μs/div
VOUT
2V/div
VIN+
50mV/div
PROPAGATION DELAY (tPD+) (VCC = 3V)MAX9015 toc37
10μs/div
VOUT
2V/div
VIN+
50mV/div
PROPAGATION DELAY (tPD-) (VCC = 1.8V)MAX9015 toc38
2μs/div
VOUT
1V/div
VIN+
50mV/div
PROPAGATION DELAY (tPD+) (VCC = 1.8V)MAX9015 toc39
10μs/div
VOUT
1V/div
VIN+
50mV/div
1kHz RESPONSE (VCC = 5V)MAX9015 toc40
200μs/div
OUT
2V/div
IN+
50mV/div
AC-COUPLED
SLOW POWER-UP/DOWN RESPONSEMAX9015 toc41
40μs/div
VOUT
1V/div
VCC
1V/div
POWER-UP RESPONSEMAX9015 toc42
20μs/div
VREF
1V/div
VCC
2V/div
VOUT
2V/div
Typical Operating Characteristics (continued)(VCC= 5V, VEE= 0V, CL= 15pF, VOVERDRIVE= 100mV, TA= +25°C, unless otherwise noted.)