MAX4714EXT-T ,0.8 / Low-Voltage / Single-Supply SPDT Analog Switch in SC70ELECTRICAL CHARACTERISTICS—Single +3V Supply(V+ = +2.7V to +3.6V, V = +1.4V, V = +0.5V, T = T to T ..
MAX4715EXK+T ,0.4Ω, Low-Voltage, Single-Supply SPST Analog SwitchesFeaturesThe MAX4715/MAX4716 are low on-resistance, low-♦ Low RONvoltage, single-pole/single-throw ( ..
MAX4715EXK+T ,0.4Ω, Low-Voltage, Single-Supply SPST Analog SwitchesApplicationsPower RoutingBattery-Operated EquipmentAudio and Video Signal RoutingLow-Voltage Data-A ..
MAX4715EXK-T ,0.4 / Low-Voltage / Single-Supply SPST Analog Switches in SC70ApplicationsPower RoutingBattery-Operated EquipmentAudio and Video Signal RoutingLow-Voltage Data-A ..
MAX4716EXK+T ,0.4Ω, Low-Voltage, Single-Supply SPST Analog SwitchesELECTRICAL CHARACTERISTICS—Single +3V Supply(V+ = +2.7V to +3.6V, V = +1.4V, V = +0.5V, T = T to T ..
MAX4716EXK-T ,0.4 / Low-Voltage / Single-Supply SPST Analog Switches in SC70ELECTRICAL CHARACTERISTICS—Single +3V Supply(V+ = +2.7V to +3.6V, V = +1.4V, V = +0.5V, T = T to T ..
MAX8866SEUA ,Dual / Low-Dropout / 100mA Linear Regulators
MAX8866SEUA+ ,Dual, Low-Dropout, 100mA Linear Regulators
MAX8866TEUA+ ,Dual, Low-Dropout, 100mA Linear Regulators
MAX8867EUK25-T ,Low-noise, low-dropout, 150mA linear regulator. Preset output voltage 2.50V
MAX8867EUK28+T ,Low-noise, low-dropout, 150mA linear regulator. Preset output voltage 2.80V
MAX8867EUK28-T ,Low-noise, low-dropout, 150mA linear regulator. Preset output voltage 2.80V
MAX4714EXT-T
0.8 / Low-Voltage / Single-Supply SPDT Analog Switch in SC70
General DescriptionThe MAX4714 is a low on-resistance, low-voltage sin-
gle-pole/double-throw (SPDT) analog switch that oper-
ates from a single +1.6V to +3.6V supply. The
MAX4714 has break-before-make switching. This
device also has fast switching speeds (tON= 18ns
max, tOFF= 12ns max).
When powered from a +3V supply, the MAX4714 fea-
tures 0.8Ωmax on-resistance (RON), with 0.18Ωmax
RONmatching and flatness. The digital logic input is
1.8V CMOS compatible when using a single +3V sup-
ply.
The MAX4714 is pin compatible with the MAX4599 and
is available in a 6-pin SC70 package.
Applications Power Routing
Battery-Operated Equipment
Audio and Video Signal Routing
Low-Voltage Data-Acquisition Systems
Communications Circuits
PCMCIA Cards
Cellular Phones
Modems
Hard Drives
FeaturesLow RON
0.8Ωmax (+3V Supply)
2.5Ωmax (+1.8V Supply)0.18Ωmax RONFlatness (+3V Supply)+1.6V to +3.6V Single-Supply OperationAvailable in 6-Pin SC70 PackageFast Switching: tON= 18ns max, tOFF= 12ns max1.8VCMOS Logic Compatible (+3V Supply)Pin Compatible with MAX4599Guaranteed Break-Before-Make
MAX4714
0.8Ω, Low-Voltage, Single-Supply
SPDT Analog Switch in SC7019-1982; Rev 0; 4/01
Ordering Information
Pin Configuration/
Functional Diagram/Truth Table
MAX4714
0.8Ω, Low-Voltage, Single-Supply
SPDT Analog Switch in SC70
ABSOLUTE MAXIMUM RATINGSStresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
Voltages Referenced to GND
V+, IN....................................................................-0.3V to +4V
COM, NC, NO (Note 1)..............................-0.3V to (V+ + 0.3V)
Continuous Current NO, NC to COM..............................±150mA
Peak Current NO, NC to COM
(pulsed at 1ms, 10% duty cycle max)........................±300mA
Continuous Power Dissipation
6-Pin SC70 (derate 3.1mW/°C above +70°C)...............247mW
Operating Temperature Range
MAX4714EXT....................................................-40°C to +85°C
Junction Temperature......................................................+150°C
Storage Temperature Range.............................-65°C to +150°C
Lead Temperature (soldering, 10s)................................+300°C
Note 1:Signals on NC, NO, and COM exceeding V+ or GND are clamped by internal diodes.
ELECTRICAL CHARACTERISTICS—Single +3V Supply(V+ = +2.7V to +3.6V, VIH= +1.4V, VIL= +0.5V, TA= TMINto TMAX, unless otherwise noted. Typical values are at V+ = +3.0V and
MAX4714
0.8Ω, Low-Voltage, Single-Supply
SPDT Analog Switch in SC70
ELECTRICAL CHARACTERISTICS—Single +1.8V Supply
ELECTRICAL CHARACTERISTICS—Single +3V Supply (continued)(V+ = +2.7V to +3.6V, VIH= +1.4V, VIL= +0.5V, TA= TMINto TMAX, unless otherwise noted. Typical values are at V+ = +3.0V and
MAX4714
0.8Ω, Low-Voltage, Single-Supply
SPDT Analog Switch in SC70
Note 2:The algebraic convention, where the most negative value is a minimum and the most positive value is a maximum, is used in
this data sheet.
Note 3:SC70-packaged parts are 100% tested at +25°C. Limits across the full temperature range are guaranteed by design and
correlation.
Note 4:∆RON= RON(MAX)- RON(MIN).
Note 5:Flatness is defined as the difference between the maximum and minimum values of on-resistance as measured over the
specified analog signal range.
Note 6:Guaranteed by design.
Note 7:Off-Isolation = 20log10[VCOM/ (VNCor VNO)], VCOM= output, VNCor VNO= input to off switch.
Note 8:Between the two switches.
ELECTRICAL CHARACTERISTICS—Single +1.8V Supply (continued)(V+ = +1.8V, VIH= +1V, VIL= +0.4V, TA= TMINto TMAX, unless otherwise noted. Typical values are at TA= +25°C.) (Notes 2, 3)
ypical Operating Characteristics (TA = +25°C, unless otherwise noted.)
MAX4714
0.8Ω, Low-Voltage, Single-Supply
SPDT Analog Switch in SC70
Typical Operating Characteristics (continued)(TA = +25°C, unless otherwise noted.)
Pin Description
MAX4714
0.8Ω, Low-Voltage, Single-Supply
SPDT Analog Switch in SC70Rail-to-Rail is a registered trademark of Nippon Motorola, Ltd.
Detailed DescriptionThe MAX4714 is a low-on-resistance (RON), low-volt-
age, single-pole/double-throw (SPDT) analog switch
that operates from a +1.6V to +3.6V supply. The
MAX4714 has break-before-make switching. This
device also has fast switching speeds (tON= 18ns
max, tOFF= 12ns max).
When powered from a +3V supply, the 0.8Ωmax RON
allows high continuous currents to be switched in a
variety of applications.
Applications Information
Logic InputsThe MAX4714 logic input can be driven up to +3.6V
regardless of the supply voltage. For example, with a
+3.3V supply, IN may be driven low to GND and high to
+3.6V. Driving IN Rail-to-Rail®minimizes power con-
sumption.
Analog Signal LevelsAnalog signals that range over the entire supply voltage
(V+ to GND) can be passed with very little change in
on-resistance (see Typical Operating Characteristics).
The switches are bidirectional, so the NO, NC, and
COM pins can be used as either inputs or outputs.
Chip InformationTRANSISTOR COUNT: 135
PROCESS: CMOS
