MAX4711EUE ,Fault-Protected / Low-Voltage / Quad SPST Analog SwitchesELECTRICAL CHARACTERISTICS—Dual Supplies(V+ = +4.5V to +5.5V, V- = -4.5V to -5.5V, V = +2.4V, V = + ..
MAX4712ESE ,Fault-Protected / Low-Voltage / Quad SPST Analog SwitchesMAX4711/MAX4712/MAX471319-1907; Rev 0; 1/01Fault-Protected, Low-Voltage, Quad SPST Analog Switches
MAX4712ESE+T ,Fault-Protected, Low-Voltage, Quad SPST Analog SwitchesApplicationsMAX4711ESE -40°C to +85°C 16 Narrow SOCommunication SystemsMAX4711EPE -40°C to +85°C 16 ..
MAX4714EXT ,PLASTIC ENCAPSULATED DEVICES MAX4714EXT Rev. A RELIABILITY REPORT FOR MAX4714EXT PLASTIC EN ..
MAX4714EXT+T ,0.8-Ohm, Low-Voltage, Single-Supply SPDT Analog Switch in SC70Applications Ordering InformationPower RoutingPIN- TOPPART TEMP RANGEBattery-Operated EquipmentPACK ..
MAX4714EXT-T ,0.8 / Low-Voltage / Single-Supply SPDT Analog Switch in SC70ELECTRICAL CHARACTERISTICS—Single +3V Supply(V+ = +2.7V to +3.6V, V = +1.4V, V = +0.5V, T = T to T ..
MAX8866SEUA ,Dual / Low-Dropout / 100mA Linear Regulators
MAX8866SEUA+ ,Dual, Low-Dropout, 100mA Linear Regulators
MAX8866TEUA+ ,Dual, Low-Dropout, 100mA Linear Regulators
MAX8867EUK25-T ,Low-noise, low-dropout, 150mA linear regulator. Preset output voltage 2.50V
MAX8867EUK28+T ,Low-noise, low-dropout, 150mA linear regulator. Preset output voltage 2.80V
MAX8867EUK28-T ,Low-noise, low-dropout, 150mA linear regulator. Preset output voltage 2.80V
MAX4711CSE-MAX4711ESE-MAX4711EUE-MAX4712ESE
Fault-Protected / Low-Voltage / Quad SPST Analog Switches
General DescriptionThe MAX4711/MAX4712/MAX4713 are fault-protected,
Rail-to-Rail®, low-voltage analog switches featuring low
on-resistance and guaranteed on-resistance flatness over
the specified signal range. Due to the fault protection fea-
ture the analog switch input (NO_ or NC_) and output
(COM_) pins are not symmetrical. The fault protection fea-
ture allows for the analog input to go beyond the plus or
minus supplies without the device drawing excessive
amounts of current from the analog inputs. When the ana-
log inputs are driven beyond the supply rails when the
switch is on, it will sense a fault and turn itself off and the
analog switch output will be clamped to the same polarity
supply as the input signal and will not go beyond the sup-
ply rails. This feature protects any electronic circuitry con-
nected to the output from excessive voltages present on
the analog inputs.
The MAX4711/MAX4712/MAX4713 are quad, single-
pole/single-throw (SPST) analog switches. The MAX4711
has four normally closed switches (NC), the MAX4712 has
four normally open switches (NO), and the MAX4713 has
two NO and two NC switches. Switching times are less
than 125ns for tON, and less than 80ns for tOFF. These
switches operate from a single +2.7V to +11V supply or
from dual ±2.7V to ±5.5V supplies. All digital inputs have
+0.8V to +2.4V logic thresholds, ensuring both TTL and
CMOS logic compatibility when using ±4.5V to ±5.5V or
single +4.5V to +11V supplies.
________________________ApplicationsCommunication Systems
Battery-Operated Systems
Signal Routing
Test Equipment
Data-Acquisition
Industrial and Process Control Systems
Avionics
Redundant/Backup Systems
FeaturesFault-Protected Analog Inputs±12V Fault Protection with Power Off±7V Fault Protection with ±5V Supplies+12V and -7V Fault Protection with +5V Supply+12V and -9V Fault Protection with +3V SupplyFault-Protected Digital Inputs May Exceed V+
Supply RailAll Switches Off with Power OffRail-to-Rail Signal HandlingOutput Clamped to Appropriate Supply Voltages
During Fault Condition25Ωmax RONat +25°C1Ωmax On-Resistance Match Between ChannelsSingle and Dual Supply OperationPin-Compatible with Industry Standard
MAX391/MAX392/MAX393TTL and CMOS Compatible Logic Inputs19-1907; Rev 0; 1/01
MAX4711/MAX4712/MAX4713
Fault-Protected, Low-Voltage,
Quad SPST Analog Switches
Pin Configurations/Functional
Diagrams/Truth Tables
Ordering Information
Ordering Information continued at end of data sheet.
Pin Configurations/Functional Diagrams/Truth Tables
continued at end of data sheet.Rail-to-Rail is a registered trademark of Nippon Motorola, Inc.
MAX4711/MAX4712/MAX4713
Fault-Protected, Low-Voltage,
Quad SPST Analog Switches
ABSOLUTE MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS—Dual Supplies(V+ = +4.5V to +5.5V, V- = -4.5V to -5.5V, VIH= +2.4V, VIL= +0.8V, GND = 0, TA= TMINto TMAX, unless otherwise noted. Typical
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability............................................................................-0.3V to +13V
V-............................................................................-13V to +0.3V
V+ to V-...................................................................-0.3V to +13V
IN_...........................................................(V- + 12V) to (V- - 0.3V)
COM_ (Note 1)......................................(V- - 0.3V) to (V+ + 0.3V)
NO_, NC_ (Note 2)..................................(V+ - 12V) to (V- + 12V)
Continuous Current into Any Terminal..............................±40mA
Peak Current, into Any Terminal
(pulsed at 1ms,10% duty cycle).................................±70mA
Continuous Power Dissipation (TA= +70°C)
TSSOP (derate 5.70mW/°C above +70°C)..................457mW
Narrow SO (derate 8.70mW/°C above +70°C)............696mW
Plastic Dip (derate 10.53mW/°C above +70°C)...........842mW
Operating Temperature Ranges
MAX471_C_ E.....................................................0°C to +70°C
MAX471_E_ E..................................................-40°C to +85°C
Junction Temperature......................................................+150°C
Storage Temperature Range.............................-65°C to +150°C
Lead Temperature (soldering, 10s).................................+300°C
Note 1:COM_ pin is not fault-protected. Signals on COM_ exceeding V+ or V- are clamped by internal diodes. Limit forward diode
current to maximum current rating.
Note 2:NO_ and NC_ pins are fault-protected. Signals on NO_ or NC_ exceeding -12V to +12V may damage device. These limits
apply with V+ = V- = 0.
MAX4711/MAX4712/MAX4713
Fault-Protected, Low-Voltage,
Quad SPST Analog Switches
ELECTRICAL CHARACTERISTICS—Dual Supplies (continued)
MAX4711/MAX4712/MAX4713
Fault-Protected, Low-Voltage,
Quad SPST Analog Switches
ELECTRICAL CHARACTERISTICS—Dual Supplies (continued)(V+ = +4.5V to +5.5V, V- = -4.5V to -5.5V, VIH= +2.4V, VIL= +0.8V, GND = 0, TA= TMINto TMAX, unless otherwise noted. Typical
values are at TA= +25°C.) (Note 3)
ELECTRICAL CHARACTERISTICS—+5V Single Supply(V+ = +4.5V to +5.5V, V- = 0, VIH= +2.4V, VIL= +0.8V, GND = 0, TA= TMINto TMAX, unless otherwise noted. Typical values are at
MAX4711/MAX4712/MAX4713
Fault-Protected, Low-Voltage,
Quad SPST Analog Switches
ELECTRICAL CHARACTERISTICS—+5V Single Supply (continued)(V+ = +4.5V to +5.5V, V- = 0, VIH= +2.4V, VIL= +0.8V, GND = 0, TA= TMINto TMAX, unless otherwise noted. Typical values are at
MAX4711/MAX4712/MAX4713
Fault-Protected, Low-Voltage,
Quad SPST Analog Switches
ELECTRICAL CHARACTERISTICS—+3V Single Supply(V+ = +2.7V to +3.6V, V- = 0, VIH= +2.0V, VIL= +0.6V, GND = 0, TA= TMINto TMAX, unless otherwise noted. Typical values are at= +25°C.) (Note 3)
MAX4711/MAX4712/MAX4713
Fault-Protected, Low-Voltage,
Quad SPST Analog Switches
ELECTRICAL CHARACTERISTICS—+3V Single Supply (continued)(V+ = +2.7V to +3.6V, V- = 0, VIH= +2.0V, VIL= +0.6V, GND = 0, TA= TMINto TMAX, unless otherwise noted. Typical values are at= +25°C.) (Note 3)
Note 3:Algebraic convention is used in this data sheet; the most negative value is shown in the minimum column.
Note 4:∆RON= ∆RON(MAX) - ∆RON(MIN)
Note 5:Leakage parameters are 100% tested at maximum rated temperature and with dual supplies. Leakage parameters
with single supply are guaranteed by correlation at +25°C.
Note 6:Off-isolation = 20 log10[VCOM_/(VNO_or VNC_)], VCOM_= output, VNO_or VNC_= input to off switch.
Note 7:Between any two switches.
MAX4711/MAX4712/MAX4713
Fault-Protected, Low-Voltage,
Quad SPST Analog Switches
Typical Operating Characteristics(V+ = +5V, V- = -5V, TA = +25°C, unless otherwise noted.)
MAX4711/MAX4712/MAX4713
Fault-Protected, Low-Voltage,
Quad SPST Analog Switches
Typical Operating Characteristics (continued)(V+ = +5V, V- = -5V, TA = +25°C, unless otherwise noted.)
