MAX4662CPE ,2.5W / Quad / SPST / CMOS Analog SwitchesApplicationsMAX4661CWE 0°C to +70°C 16 Wide SOReed Relay Replacement AvionicsMAX4661CPE 0°C to +70° ..
MAX4662CPE+ ,2.5 Ohm Quad, SPST, CMOS Analog Switchesapplications♦ Rail-to-Rail Signal Handlingand are the preferred solution over mechanical relays ina ..
MAX4662CWE ,2.5W / Quad / SPST / CMOS Analog SwitchesELECTRICAL CHARACTERISTICS—Dual Supplies(V+ = +15V, V- = -15V, V = +5V, V = +2.4V, V = +0.8V, T = T ..
MAX4662EAE ,2.5W / Quad / SPST / CMOS Analog Switchesapplications where current♦ Guaranteed Break-Before-Make (MAX4663)switching is required. They have ..
MAX4662EAE+ ,2.5 Ohm Quad, SPST, CMOS Analog SwitchesFeaturesThe MAX4661/MAX4662/MAX4663 quad analog switches♦ Low On-Resistance (2.5W max)feature low o ..
MAX4662EAE+T ,2.5 Ohm Quad, SPST, CMOS Analog SwitchesMAX4661/MAX4662/MAX466319-1516; Rev 0; 7/992.5W , Quad, SPST, CMOS Analog Switches
MAX882ESA+T ,5V/3.3V or Adjustable, Low-Dropout, Low-IQ, 200mA Linear Regulator with Standby ModeELECTRICAL CHARACTERISTICS(V = 6V (MAX883) or V = 4.3V (MAX882/MAX884), C = 2.2µF, STBY or OFF = V ..
MAX882ESA-T ,5V/3.3V or Adjustable, Low-Dropout, Low-IQ, 200mA Linear Regulator with Standby ModeMAX882/MAX883/MAX88419-0275; Rev 4; 7/095V/3.3V or Adjustable, Low-Dropout, Low I , 200mA Linear Re ..
MAX8833ETJ+ ,Dual, 3A, 2MHz Step-Down RegulatorELECTRICAL CHARACTERISTICS(V = V = V = 3.3V, V = 0.5V, V = V = 600mV, PGND_ = GND, R = 10kΩ, L = 0. ..
MAX8833ETJ+ ,Dual, 3A, 2MHz Step-Down Regulatorapplications. Total output♦ ±1% Output Accuracy over Load, Line,and Temperatureerror is less than ± ..
MAX8833ETJ+T ,Dual, 3A, 2MHz Step-Down RegulatorApplicationsASIC/CPU/DSP Power SuppliesTypical Operating CircuitDDR Power SuppliesINPUT2INPUT1Set-T ..
MAX8834YEWP+T ,Adaptive Step-Up Converters with 1.5A Flash Driverfeatures include an optional NTC input for finger-burn protection and open/short LED detection. The ..
MAX4661CAE-MAX4661CWE-MAX4661EAE-MAX4661EWE-MAX4662CAE-MAX4662CPE-MAX4662CWE-MAX4662EAE-MAX4663CAE-MAX4663CPE-MAX4663CWE
2.5W / Quad / SPST / CMOS Analog Switches
General DescriptionThe MAX4661/MAX4662/MAX4663 quad analog switches
feature low on-resistance of 2.5Ωmax. On-resistance is
matched between switches to 0.5Wmax and is flat
(0.5Wmax) over the specified signal range. Each
switch can handle Rail-to-Rail®analog signals. Off-
leakage current is only 5nA max at TA= +85°C. These
analog switches are ideal in low-distortion applications
and are the preferred solution over mechanical relays in
automatic test equipment or applications where current
switching is required. They have lower power require-
ments, use less board space, and are more reliable
than mechanical relays.
The MAX4661 has four normally closed (NC) switches,
and the MAX4662 has four normally open (NO) switches.
The MAX4663 has two NC and two NO switches, and fea-
tures guaranteed break-before-make switching.
These devices operate from a single +4.5V to +36V sup-
ply or from dual ±4.5V to ±20V supplies. A separate logic
supply pin guarantees TTL/CMOS-logic compatibility
when operating across the entire supply voltage range.
ApplicationsReed Relay ReplacementAvionics
Test EquipmentADC Systems
Communication SystemsSample-and-Hold Circuits
PBX, PABX SystemsData Acquisition Systems
Audio-Signal Routing
FeaturesLow On-Resistance (2.5Wmax)Guaranteed RONMatch Between Channels
(0.5Wmax)Guaranteed RONFlatness over Specified Signal
Range (0.5Wmax)Rail-to-Rail Signal HandlingGuaranteed Break-Before-Make (MAX4663)> 2kV ESD Protection per Method 3015.7+4.5V to +36V Single-Supply Operation
±4.5V to ±20V Dual-Supply OperationTTL/CMOS-Compatible Control Inputs
MAX4661/MAX4662/MAX4663
2.5W, Quad, SPST,
CMOS Analog Switches19-1516; Rev 0; 7/99
Ordering Information
Pin Configurations/Functional Diagrams/Truth TablesRail-to-Rail is a registered trademark of Nippon Motorola, Ltd.
MAX4661/MAX4662/MAX4663
2.5W, Quad, SPST,
CMOS Analog Switches
ABSOLUTE MAXIMUM RATINGSStresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
V+ to GND..............................................................-0.3V to +44V
V- to GND..............................................................+0.3V to -44V
V+ to V-...................................................................-0.3V to +44Vto GND.......................................(GND - 0.3V) to (V+ + 0.3V)
All Other Pins to GND (Note 1).............(V- - 0.3V) to (V+ + 0.3V)
Continuous Current (COM_, NO_, NC_) ........................±200mA
Peak Current (COM_, NO_, NC_)
(pulsed at 1ms, 10% duty cycle)................................±300mA
Continuous Power Dissipation (TA= +70°C)
SSOP (derate 7.1mW/°C above +70°C).......................571mW
Wide SO (derate 9.52mW/°C above +70°C).................762mW
Plastic DIP (derate 10.53mW/°C above +70°C)...........842mW
Operating Temperature Ranges
MAX466_C_E ......................................................0°C to +70°C
MAX466_E_E....................................................-40°C to +85°C
Storage Temperature Range.............................-65°C to +150°C
Lead Temperature (soldering, 10sec).............................+300°C
ELECTRICAL CHARACTERISTICS—Dual Supplies(V+ = +15V, V- = -15V, VL= +5V, VIN_H= +2.4V, VIN_L= +0.8V, TA = TMINto TMAX, unless otherwise noted. Typical values are at = +25°C.) (Note 2)
Note 1: Signals on NC_, NO_, COM_, or IN_ exceeding V+ or V- will be clamped by internal diodes. Limit forward diode current to maximum current rating.
MAX4661/MAX4662/MAX4663
2.5W, Quad, SPST,
CMOS Analog Switches
ELECTRICAL CHARACTERISTICS—Dual Supplies (continued)(V+ = +15V, V- = -15V, VL= +5V, VIN_H= +2.4V, VIN_L= +0.8V, TA = TMINto TMAX, unless otherwise noted. Typical values are at = +25°C.) (Note 2)
MAX4661/MAX4662/MAX4663
2.5W, Quad, SPST,
CMOS Analog Switches
ELECTRICAL CHARACTERISTICS—Single Supply(V+ = +12V, V- = 0, VL= +5V, VIN_H= +2.4V, VIN_L= +0.8V, TA = TMINto TMAX, unless otherwise noted. Typical values are at = +25°C.) (Note 2)
MAX4661/MAX4662/MAX4663
2.5W, Quad, SPST,
CMOS Analog Switches
ELECTRICAL CHARACTERISTICS—Single Supply (continued)(V+ = +12V, V- = 0, VL= +5V, VIN_H= +2.4V, VIN_L= +0.8V, TA = TMINto TMAX, unless otherwise noted. Typical values are at = +25°C.) (Note 2)
Note 2:The algebraic convention, where the most negative value is a minimum and the most positive value a maximum, is used in
this data sheet.
Note 3:Guaranteed by design.
Note 4:DRON= RON(MAX)- RON(MIN).
Note 5:Flatness is defined as the difference between the maximum and minimum value of on-resistance as measured over the
specified analog signal range.
Note 6:Leakage parameters are 100% tested at maximum-rated hot temperature and guaranteed by correlation at +25°C.
Note 7:Off-isolation = 20log10[VCOM/ (VNCor VNO)], VCOM= output, VNCor VNO= input to off switch.
Note 8:Between any two switches.
Note 9:Leakage testing at single supply is guaranteed by testing with dual supplies.
MAX4661/MAX4662/MAX4663
2.5W, Quad, SPST,
CMOS Analog Switches
Typical Operating Characteristics(TA = +25°C, unless otherwise noted.)
