MAX4614ESD+T ,Low-Voltage, High-Speed, Quad, SPST CMOS Analog SwitchesMAX4614/MAX4615/MAX461619-1501; Rev 0; 7/99Low-Voltage, High-Speed, Quad, SPST CMOS Analog Switches
MAX4614EUD ,Low-Voltage, High-Speed, Quad, SPST CMOS Analog SwitchesApplicationsPART TEMP. RANGE PIN-PACKAGEBattery-Operated EquipmentMAX4614CUD 0°C to +70°C 14 TSSOPA ..
MAX4614EUD ,Low-Voltage, High-Speed, Quad, SPST CMOS Analog SwitchesMAX4614/MAX4615/MAX461619-1501; Rev 0; 7/99Low-Voltage, High-Speed, Quad, SPST CMOS Analog Switches
MAX4614EUD+ ,Low-Voltage, High-Speed, Quad, SPST CMOS Analog SwitchesApplicationsPART TEMP. RANGE PIN-PACKAGEBattery-Operated EquipmentMAX4614CUD 0°C to +70°C 14 TSSOPA ..
MAX4614EUD+ ,Low-Voltage, High-Speed, Quad, SPST CMOS Analog SwitchesFeaturesThe MAX4614/MAX4615/MAX4616 quad, low-voltage,♦ Fast Switching Times high-speed, single-pol ..
MAX4614EUD+T ,Low-Voltage, High-Speed, Quad, SPST CMOS Analog SwitchesGeneral Description ________
MAX8742EAI , 500kHz Multi-Output Power-Supply Controllers with High Impedance in Shutdown
MAX8742EAI+ ,500kHz Multi-Output Power-Supply Controllers with High Impedance in ShutdownFeaturesThe MAX8741/MAX8742 are buck-topology, step-down,♦ 97% Efficiencyswitch-mode, power-supply ..
MAX8743 ,Dual, High-Efficiency, Step-Down Controller with High Impedance in ShutdownFeaturesThe MAX8743 is a dual pulse-width modulation (PWM)♦ Ultra-High Efficiencycontroller configu ..
MAX8743EEI ,Dual, High-Efficiency, Step-Down Controller with High Impedance in ShutdownFeaturesThe MAX8743 is a dual pulse-width modulation (PWM)♦ Ultra-High Efficiencycontroller configu ..
MAX8743EEI . ,Dual, High-Efficiency, Step-Down Controller with High Impedance in ShutdownELECTRICAL CHARACTERISTICS(Circuit of Figure 1, V = V = 5V, SKIP = AGND, V+ = 15V, T = 0°C to +85°C ..
MAX8743EEI+ ,Dual, High-Efficiency, Step-Down Controller with High Impedance in ShutdownMAX874319-3318; Rev 1; 8/05Dual, High-Efficiency, Step-DownController with High Impedance in Shutdo ..
MAX4614CPD+-MAX4614CSD+-MAX4614CSD+T-MAX4614CUD+-MAX4614ESD+T-MAX4614EUD+-MAX4614EUD+T-MAX4615CUD+-MAX4616CUD+-MAX4616ESD+-MAX4616EUD+-MAX4616EUD+T
Low-Voltage, High-Speed, Quad, SPST CMOS Analog Switches
MAX4614/MAX4615/MAX4616
Low-Voltage, High-Speed, Quad, SPST
CMOS Analog Switches19-1501; Rev 0; 7/99
General DescriptionThe MAX4614/MAX4615/MAX4616 quad, low-voltage,
high-speed, single-pole/single-throw (SPST) analog
switches are pin compatible with the industry-standard
74HC4066/MAX4610 analog switches. On-resistance
(10Ωmax) is matched between switches to 1Ωmax
and is flat (1Ωmax) over the specified signal range.
Each switch handles V+ to GND analog signal levels.
Maximum off-leakage current is only 1nA at TA= +25°C
and 6nA at TA= +85°C.
The MAX4614 has four normally open (NO) switches,
and the MAX4615 has four normally closed (NC)
switches. The MAX4616 has two NO switches and two
NC switches. These CMOS switches operate from a
single +2V to +5.5V supply. All digital inputs have
+0.8V and +2.4V logic thresholds, ensuring TTL/CMOS-
logic compatibility when using a single +5V supply.
________________________ApplicationsBattery-Operated Equipment
Audio/Video Signal Routing
Low-Voltage Data-Acquisition Systems
Sample-and-Hold Circuits
Communication Circuits
____________________________FeaturesFast Switching Times
12ns tON, 10ns tOFFPin Compatible with Industry-Standard
74HC4066/MAX4610Guaranteed On-Resistance
10Ωmax (+5V supply)
20Ωmax (+3V supply)Guaranteed Match Between Channels (1Ωmax)Guaranteed Flatness Over Signal Range (1Ωmax)<6nA Off-Leakage Current Over Temperature
(TA= +85°C)Rail-to-Rail®Signal HandlingTTL/CMOS-Logic CompatibleMAX4614
TSSOP/SO/DIPIN1
IN4
NO4
COM4
COM3
NO3
COM2
NO2
COM1
NO1
GND
IN3
IN2
TOP VIEW
INPUTSWITCH STATELOW
HIGH
OFF
MAX4615
TSSOP/SO/DIPIN1
IN4
NC4
COM4
COM3
NC3
COM2
NC2
COM1
NC1
GND
IN3
IN2
INPUTSWITCH STATELOW
HIGH
OFF
MAX4616
TSSOP/SO/DIPIN1
IN4
NC4
COM4
COM3
NO3
COM2
NC2
COM1
NO1
GND
IN3
IN2
INPUTNO1, NO3LOW
HIGH
OFF
NC2, NC4OFF
Pin Configurations/Truth Tables
Ordering Information
Ordering Information continued at end of data sheet.
PART
MAX4614CUD0°C to +70°C
TEMP. RANGEPIN-PACKAGE14 TSSOP
MAX4614CSD
MAX4614CPD0°C to +70°C
0°C to +70°C14 Narrow SO
14 Plastic DIP
MAX4614ESD-40°C to +85°C14 Narrow SO
MAX4614EUD-40°C to +85°C14 TSSOP
Rail-to-Rail is a registered trademark of Nippon Motorola, Ltd.
MAX4614EPD-40°C to +85°C14 Plastic DIP
MAX4614/MAX4615/MAX4616
Low-Voltage, High-Speed, Quad, SPST
CMOS Analog Switches
ABSOLUTE MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS—Single +5V Supply(V+ = +5V ±10%, VIN_H= 2.4V, VIN_L= 0.8V, TA= TMINto TMAX, unless otherwise noted.) (Note 2)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
(Voltages referenced to GND)
V+, IN_......................................................................-0.3V to +6V
COM_, NO_, NC_ (Note 1).........................-0.3V to (V+ + 0.03V)
Continuous Current (any terminal)....................................±75mA
Peak Current (NO_, NC_, COM_)
(pulsed at 1ms, 10% duty cycle).................................±200mA
Continuous Power Dissipation (TA= +70°C)
14-Pin TSSOP (derate 6.3mW/°C above +70°C)..........500mW
14-Pin Narrow SO (derate 8.00mW/°C above +70°C)..640mW
14-Pin Plastic DIP (derate 10.00mW/°C above +70°C)...800mW
Operating Temperature Ranges
MAX461_C_ _......................................................0°C to +70°C
MAX461_E_ _....................................................-40°C to +85°C
Storage Temperature Range.............................-65°C to +150°C
Lead Temperature (soldering, 10sec).............................+300°C
V+ = 5.5V;
VCOM_= 1V, 4.5V;
VNO_= 4.5V, 1V
V+ = 4.5V,
ICOM_= 10mA,
VNO_= VNC_= 3V
V+ = 4.5V;
ICOM_= 10mA;
VNO_= VNC_= 3V,
2V, 1V
CONDITIONSINO(OFF)NO_ or NC_ Off-Leakage
Current (Note 6)-660.011
RFLAT(ON)On-Resistance Flatness
(Note 5)0V+
VCOM_,
VNO_,
VNC_
Analog Signal Range
(Note 3)
0.31DRONOn-Resistance Match Between
Channels (Note 4)
UNITSMINTYPMAXSYMBOLPARAMETER= +25°C= +25°C= +25°C= TMINto TMAX
TA= +25°C= TMINto TMAX
V+ = 5.5V;
VCOM_= 1V, 4.5V;
VNO_= VNC_= 4.5V,
TA= +25°CICOM(OFF)COM_ Off-Leakage Current
(Note 6)-66TA= TMINto TMAX0.011
V+ = 5.5V;
VCOM_= 1V, 4.5V;
VNO_= VNC_= 1V,
4.5V, or floatingICOM(ON)COM_ On-Leakage Current
(Note 6)-1212
TA= +25°C= TMINto TMAX0.022
On-ResistanceRONΩ
V+ = 4.5V,
ICOM_= 10mA,
VNO_= VNC_= 3V
Note 1:Signals on NO_, NC_, or COM_ exceeding V+ or GND are clamped by internal diodes. Limit forward-diode current to maxi-
mum current rating.
ANALOG SWITCH= TMINto TMAX1.2TA= TMINto TMAX
MAX4614/MAX4615/MAX4616
Low-Voltage, High-Speed, Quad, SPST
CMOS Analog Switches
ELECTRICAL CHARACTERISTICS—Single +5V Supply (continued)(V+ = +5V ±10%, VIN_H= 2.4V, VIN_L= 0.8V, TA= TMINto TMAX, unless otherwise noted.) (Note 2)
PARAMETERSYMBOLMINTYPMAXUNITSInput Current with Input
Voltage HighIIN_H-100.310nA
CONDITIONSVIN_= 2.4V
Input Current with Input
Voltage LowIIN_L-100.310nAVIN_= 0.8V
Turn-On Time (Note 3)tON512ns
Charge InjectionQ6.5pC= +25°C= TMINto TMAX14VCOM_= 3V, Figure 2= +25°C= TMINto TMAX12VCOM_= 3V, Figure 2Turn-Off Time(Note 3)tOFF2.510ns
Power-Supply Range
On-Channel BandwidthBW70MHz
Signal = 0dBm, Figure 4, 50Ωin and out,= +25°C= 50Ω, f = 100kHz, Figure 4,= +25°COff-Isolation (Note 7)VISO-85dB= 50Ω, f = 100kHz, Figure 5,= +25°CCrosstalk (Note 8)VCT-96dB
f = 1MHz, Figure 6, TA= +25°CNO_ or NC_ CapacitanceC(OFF)5pF
f = 1MHz, Figure 6, TA= +25°CCOM_ Off-CapacitanceCCOM(OFF)5pF
f = 1MHz, Figure 6, TA= +25°CCOM_On-CapacitanceCCOM(ON)pF5.5V
Power-Supply CurrentVIN= 0 or V+, all switches on or off-10.0011µA
Signal = 0dBm, Figure 4, 50Ωin and out,= +25°C
600ΩIN and OUT, f = 20Hz to 20kHz, 2Vp-p,= +25°CTotal Harmonic DistortionTHD%0.034
Input Voltage HighVIN_H2.4V
Input Voltage LowVIN_L0.8V
LOGIC INPUT
POWER SUPPLY
SWITCH DYNAMIC
MAX4614/MAX4615/MAX4616
Low-Voltage, High-Speed, Quad, SPST
CMOS Analog Switches
ELECTRICAL CHARACTERISTICS—Single +3.3V Supply(V+ = +3.3V ±10%, VIN_H= 2.4V, VIN_L= 0.5V, TA= TMINto TMAX, unless otherwise noted.) (Note 2)
PARAMETERSYMBOLMINTYPMAXUNITSAnalog Signal Range
(Note 3)
VCOM_,
VNO_,
VNC_
0V+V
CONDITIONSOn-ResistanceRON
V+ = 3V,
INO= 10mA,
VCOM_= 1.5V= +25°C= +25°C= +25°C= +25°C= +25°C= TMINto TMAX
On-Resistance Match Between
Channels (Note 4)ΔRON
V+ = 3V,
ICOM_= 1mA,
VNO_= VNC_= 1.5V
NO_ or NC_ Off-Leakage
Current (Notes 3, 6)INO(OFF)0.0021
V+ = 3.6V;
VCOM_= 1V, 3V;
VNO_= VNC_= 3V, 1V
COM_ Off-Leakage Current
(Notes 3, 6)ICOM(OFF)0.0021
V+ = 3.6V;
VCOM_= 1V, 3V;
VNO_= VNC_= 3V, 1V
COM_ On-Leakage Current
(Notes 3, 6)
V+ = 3.6V;
VCOM_= 1V, 3V;
VNO_= VNC_= 1V,
3V, or floating
ICOM(ON)0.0021
-1010= TMINto TMAX= TMINto TMAX= TMINto TMAX
-1010= TMINto TMAX25
Turn-On TimetON615nsVCOM_= 1.5V,
Figure 2
Turn-Off TimetOFF412nsVCOM_= 1.5V,
Figure 2
Input Current with Input
Voltage LowIIN_L= +25°C= +25°C= TMINto TMAX= TMINto TMAX
-100.00310nAVIN_ = 0.8V
Input Current with Input
Voltage HighIIN_H-100.00310nAVIN_ = 2V
Charge InjectionQ6.5pCCL= 1nF, VGEN= 0, RGEN= 0, TA= +25°C
Power-Supply CurrentI+-10.0011µAV+ = 3.6V, VIN= 0 or V+,
all channels on or off
Input Voltage Low VIN_L0.8V
Input Voltage High VIN_H2.0V
LOGIC INPUT
SWITCH DYNAMIC (Note 3)
ANALOG SWITCH
POWER SUPPLY
MAX4614/MAX4615/MAX4616
Low-Voltage, High-Speed, Quad, SPST
CMOS Analog Switches
PARAMETERSYMBOLMINTYPMAXUNITSAnalog Signal Range
(Note 3)
VCOM_,
VNO_,
VNC_
0V+V
CONDITIONSCOM_ to NO_ or NC_
On-ResistanceRON60
V+ = 2.5V,
ICOM_= 10mA,
VNO = 1.2V= +25°C= TMINto TMAX100
Note 2:The algebraic convention, where the most negative value is a minimum and the most positive value a maximum, is used in
this data sheet.
Note 3:Guaranteed by design.
Note 4:ΔRON= RON(max) - RON(min).
Note 5:Flatness is defined as the difference between the maximum and minimum value of on-resistance as measured over the
specified analog signal range.
Note 6:Leakage parameters are 100% tested at maximum-rated hot temperature and guaranteed by correlation at +25°C.
Note 7:Off-Isolation = 20log10(VCOM_/ VNO_), VCOM_= output, VNO_= input to off switch.
Note 8:Between any two switches.
ELECTRICAL CHARACTERISTICS—Single +2.5V Supply (V+ = +2.5V, VINH= 0.7VCC, VINL= 0.5V, TA= TMINto TMAX, unless otherwise noted.) (Note 2)
6.5Turn-On TimetONns
Turn-Off TimetOFFns2.8
ANALOG SWITCH
SWITCH DYNAMIC (Note 3)VNO_or VNC_= 1V, TA= +25°C
VNO_or VNC_= 1V, TA= +25°C
MAX4614/MAX4615/MAX4616
Low-Voltage, High-Speed, Quad, SPST
CMOS Analog Switches
__________________________________________Typical Operating Characteristics(V+ = +5V, GND = 0, TA = +25°C, unless otherwise noted.)2.02.51.01.50.53.03.54.04.55.0
ON-RESISTANCE vs. VCOM_MAX4614-16 toc01
VCOM_ (V)
ON-RESISTANCE (V+ = 2V
V+ = 3V
V+ = 5V
ON-RESISTANCE vs. VCOM_
AND TEMPERATURE
MAX6414-16 toc02
VCOM_ (V)
ON-RESISTANCE (
TA = +85°C
TA = +70°C
TA = 0°CTA = -40°C
TA = +25°C
OFF-LEAKAGE vs. TEMPERATURE
MAX4614-16 toc03
TEMPERATURE (°C)
OFF-LEAKAGE (pA)60
VCOM_ = 2.5V
VNO_ = 4.5V
ON-LEAKAGE vs. TEMPERATURE
MAX4614-16 toc04
TEMPERATURE (°C)
ON-LEAKAGE (pA)60
VCOM_ = 2.5V
VNC_ = FLOATING
SUPPLY CURRENT vs. TEMPERATURE
MAX4614-16 toc05
TEMPERATURE (°C)
I+ (nA)60
10k100k1M10M100M500M
FREQUENCY RESPONSEMAX4614-16 toc08
FREQUENCY (Hz)
GAIN (dB)
PHASE (degrees)
ON-LOSS
ON-PHASE
IN = OUT = 50Ω
OFF-ISOLATION
CHARGE INJECTION vs. VCOM_
MAX4614-16 toc06
VCOM_ (V)
CHARGE INJECTION (pC)
VIN_H INPUT LOGIC HIGH
THRESHOLD vs. V+
MAX4614-16 toc07
V+ (V)
IN_H
(V)
