MAX4605CSE ,5 / Quad / SPST / CMOS Analog Switchesapplications where current switching is' Guaranteed ESD Protection > 2000V perrequired. These switc ..
MAX4605CSE+ ,5Ω, Quad, SPST, CMOS Analog SwitchesApplicationsMAX4604EPE -40°C to +85°C 16 Plastic DIPReed Relay Replacement PBX, PABX SystemsOrderin ..
MAX4605ESE ,5 / Quad / SPST / CMOS Analog SwitchesFeaturesThe MAX4604/MAX4605/MAX4606 quad analog switch-' Low On-Resistance (5Ω max)es feature 5Ω ma ..
MAX4606ESE ,5 / Quad / SPST / CMOS Analog SwitchesApplicationsMAX4604EPE -40°C to +85°C 16 Plastic DIPReed Relay Replacement PBX, PABX SystemsOrderin ..
MAX4606ESE+ ,5Ω, Quad, SPST, CMOS Analog SwitchesELECTRICAL CHARACTERISTICS—Dual Supplies(V+ = +15V, V- = -15V, V = 5V, V = 2.4V, V = 0.8V, T = T to ..
MAX4607CSE ,2.5 / Dual / SPST / CMOS Analog SwitchesELECTRICAL CHARACTERISTICS—Dual Supplies(V+ = +15V, V- = -15V, V = +5V, V = +2.4V, V = +0.8V, T = T ..
MAX8734AEEI+ ,High-Efficiency, Quad-Output, Main Power-Supply Controllers for Notebook ComputersFeatures♦ No Current-Sense Resistor Needed (MAX8734A)The MAX8732A/MAX8733A/MAX8734A dual step-down, ..
MAX8734AEEI+T ,High-Efficiency, Quad-Output, Main Power-Supply Controllers for Notebook ComputersELECTRICAL CHARACTERISTICS(Circuit of Figure 1 and Figure 2, no load on LDO5, LDO3, OUT3, OUT5, and ..
MAX8734EEI+ , High-Efficiency, Quad-Output, Main Power-Supply Controllers for Notebook Computers
MAX8737ETE , Dual, Low-Voltage Linear Regulator Controllers with External MOSFETs
MAX8739ETP , TFT, LCD, DC-DC Converter with Operational Amplifiers
MAX8739ETP+ ,TFT, LCD, DC-DC Converter with Operational AmplifiersFeaturesThe MAX8739 includes a high-performance, step-up ● 1.8V to 5.5V Input Supply Rangeregulator ..
MAX4604EPE-MAX4604ESE-MAX4605CSE-MAX4605ESE-MAX4606ESE
5 / Quad / SPST / CMOS Analog Switches
General DescriptionThe MAX4604/MAX4605/MAX4606 quad analog switch-
es feature 5Ωmax on-resistance. On-resistance is
matched between switches to 0.5Ωmax and is flat (0.5Ω
max) over the specified signal range. Each switch can
handle Rail-to-Rail®analog signals. The off-leakage cur-
rent is only 2.5nA max at +85°C. These analog switches
are ideal in low-distortion applications and are the pre-
ferred solution over mechanical relays in automatic test
equipment or in applications where current switching is
required. These switches have low power requirements,
require less board space, and are more reliable than
mechanical relays.
The MAX4604 has four normally closed (NC) switches,
the MAX4605 has four normally open (NO) switches,
and the MAX4606 has two NC and two NO switches.
These switches operate from a single supply of +4.5V
to +36V or from dual supplies of ±4.5V to ±20V. All dig-
ital inputs have +0.8V and +2.4V logic thresholds,
ensuring TTL/CMOS logic compatibility when using
±15V supplies or a single +12V supply.
ApplicationsReed Relay ReplacementPBX, PABX Systems
Test EquipmentAudio-Signal Routing
Communication SystemsAvionics
FeaturesLow On-Resistance (5Ωmax)Guaranteed RONMatch Between Channels
(0.5Wmax)Guaranteed RONFlatness over Specified Signal
Range (0.5Wmax)Rail-to-Rail Signal HandlingGuaranteed ESD Protection > 2000V per
Method 3015.7Single-Supply Operation: +4.5V to +36V
Dual-Supply Operation: ±4.5V to ±20VTTL/CMOS-Compatible Control Inputs
MAX4604/MAX4605/MAX4606, Quad, SPST, CMOS Analog Switches
Pin Configurations/Functional Diagrams/Truth Tables19-1393; Rev 1; 8/99
Ordering InformationRail-to-Rail is a registered trademark of Nippon Motorola, Ltd.
MAX4604/MAX4605/MAX4606, Quad, SPST, CMOS Analog Switches
ABSOLUTE MAXIMUM RATINGS
Note 1:Signals on NC_, NO_, COM_, or IN_ exceeding V+ or V- are clamped by internal diodes. Limit forward-diode current to
maximum current rating.
V+ to GND..............................................................-0.3V to +44V
V- to GND..............................................................+0.3V to -44V
V+ to V-...................................................................-0.3V to +44Vto GND......................................(DGND - 0.3V) to (V+ + 0.3V)
All Other Pins to DGND (Note 1).........(V- - 0.3V) to (V+ + 0.3V)
Continuous Current (COM_, NO_, NC_) ........................±100mA
Peak Current (COM_, NO_, NC_)
(pulsed at 1ms, 10% duty cycle)...............................±300mA
Continuous Power Dissipation (TA= +70°C)
16-pin Narrow SO (derate 8.70mW/°C above +70°C)....696mW
16-pin Plastic DIP (derate 10.53mW/°C above +70°C)..842mW
Operating Temperature Ranges
MAX460_C_E ......................................................0°C to +70°C
MAX460_E_E....................................................-40°C to +85°C
Storage Temperature Range.............................-65°C to +160°C
Lead Temperature (soldering, 10sec).............................+300°C
ELECTRICAL CHARACTERISTICS—Dual Supplies(V+ = +15V, V- = -15V, VL= 5V, VIN_H= 2.4V, VIN_L= 0.8V, TA= TMINto TMAX, unless otherwise noted. Typical values are at TA= +25°C.)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
MAX4604/MAX4605/MAX4606, Quad, SPST, CMOS Analog Switches
ELECTRICAL CHARACTERISTICS—Dual Supplies (continued)(V+ = +15V, V- = -15V, VL= 5V, VIN_H= 2.4V, VIN_L= 0.8V, TA= TMINto TMAX, unless otherwise noted. Typical values are TA= +25°C.)
MAX4604/MAX4605/MAX4606, Quad, SPST, CMOS Analog Switches
ELECTRICAL CHARACTERISTICS—Single Supply(V+ = +12V, V- = 0, VL= 5V, VIN_H= 2.4V, VIN_L= 0.8V, TA= TMINto TMAX, unless otherwise noted. Typical values are at TA= +25°C.)
MAX4604/MAX4605/MAX4606, Quad, SPST, CMOS Analog Switches
ELECTRICAL CHARACTERISTICS—Single Supply (continued)(V+ = +12V, V- = 0, VL= 5V, VIN_H= 2.4V, VIN_L= 0.8V, TA= TMINto TMAX, unless otherwise noted. Typical values are at TA= +25°C.)
Note 2:The algebraic convention, where the most negative value is a minimum and the most positive value a maximum, is used in
this data sheet.
Note 3:Guaranteed by design.
Note 4:DRON= RON(MAX)- RON(MIN).
Note 5:Flatness is defined as the difference between the maximum and minimum value of on-resistance as measured over the
specified analog signal range.
Note 6:Leakage parameters are 100% tested at maximum-rated hot temperature and guaranteed by correlation at +25°C.
Note 7:Off-isolation = 20log10 [VCOM_/ (VNC_or VNO_)], VCOM_= output, VNC_or VNO_= input to off switch.
Note 8:Between any two switches.
Note 9:Leakage testing at single supply is guaranteed by testing with dual supplies.
MAX4604/MAX4605/MAX4606, Quad, SPST, CMOS Analog Switches
Typical Operating Characteristics(TA= +25°C, unless otherwise noted.)
