MAX3867ECM ,+3.3V / 2.5Gbps SDH/SONET Laser Driver with Automatic Power ControlELECTRICAL CHARACTERISTICS(V = +3.14V to +5.5V, T = -40°C to +85°C. Typical values are at V = +3.3V ..
MAX3867ECM ,+3.3V / 2.5Gbps SDH/SONET Laser Driver with Automatic Power ControlApplicationsMAX3867ECM -40°C to +85°C 48 TQFPSONET/SDH Transmission SystemsMAX3867E/D -40°C to +85° ..
MAX3869EHJ+ ,+3.3V, 2.5Gbps SDH/SONET Laser Driver with Current Monitors and APCELECTRICAL CHARACTERISTICS(V = +3.14V to +5.5V, T = -40°C to +85°C. Typical values are at V = +3.3V ..
MAX3869EHJ+ ,+3.3V, 2.5Gbps SDH/SONET Laser Driver with Current Monitors and APCApplicationsMAX3869EGJ -40°C to +85°C 32 QFN*SONET/SDH Transmission SystemsMAX3869E/D -40°C to +85° ..
MAX3872ETJ+ ,Multirate Clock and Data Recovery with Limiting AmplifierELECTRICAL CHARACTERISTICS(V = +3.0V to +3.6V, T = -40°C to +85°C. Typical values at V = +3.3V, T = ..
MAX3872ETJ+ ,Multirate Clock and Data Recovery with Limiting AmplifierApplications Ordering InformationSONET/SDH Receivers and RegeneratorsPKGPART TEMP RANGE PIN-PACKAGE ..
MAX7414EUA ,5th-Order, Lowpass, Switched-Capacitor FiltersApplicationsMAX7409CPA 0°C to +70°C 8 Plastic DIPADC Anti-Aliasing CT2 Base StationsMAX7409EUA -40° ..
MAX7414EUA ,5th-Order, Lowpass, Switched-Capacitor FiltersELECTRICAL CHARACTERISTICS—MAX7409/MAX7410(V = +5V, filter output measured at OUT, 10kΩ || 50pF loa ..
MAX7414EUA ,5th-Order, Lowpass, Switched-Capacitor FiltersFeaturesThe MAX7409/MAX7410/MAX7413/MAX7414 5th-order,' 5th-Order Lowpass Filterslowpass, switched- ..
MAX7414EUA+ ,5th-Order, Lowpass, Switched-Capacitor Filtersapplications. They feature a+5V (MAX7409/MAX7410)shutdown mode, which reduces the supply current to ..
MAX7414EUA+T ,5th-Order, Lowpass, Switched-Capacitor FiltersApplicationsMAX7409CPA 0°C to +70°C 8 Plastic DIPADC Anti-Aliasing CT2 Base StationsMAX7409EUA -40° ..
MAX7415CPA ,5th-Order / Lowpass / Elliptic / Switched-Capacitor Filtersapplications. They +5V (MAX7408/MAX7411)can be put into a low-power mode, reducing supply+3V (MAX74 ..
MAX3867ECM
+3.3V / 2.5Gbps SDH/SONET Laser Driver with Automatic Power Control
General DescriptionThe MAX3867 is a complete, single +3.3V laser driver
for SDH/SONET applications up to 2.5Gbps. The
device accepts differential PECL data and clock inputs
and provides bias and modulation currents for driving a
laser. The synchronizing input latch can be bypassed if
a clock signal is not available.
An automatic power control (APC) feedback loop is
incorporated to maintain a constant average optical
power over temperature and lifetime. The wide modula-
tion current range of 5mA to 60mA and bias current of
1mA to 100mA are easy to program, making this prod-
uct ideal for use in various SDH/SONET applications.
The MAX3867 also provides enable control, a program-
mable slow-start circuit to set the laser turn-on delay,
and a failure-monitor output to indicate when the APC
loop is unable to maintain the average optical power.
The MAX3867 is available in a small 48-pin TQFP pack-
age as well as dice.
ApplicationsSONET/SDH Transmission Systems
Add/Drop Multiplexers
Digital Cross-Connects
Section Regenerators
2.5Gbps Optical Transmitters
FeaturesSingle +3.3V or +5V Power Supply62mA Supply Current at +3.3VProgrammable Modulation Current from
5mA to 60mAProgrammable Bias Current from 1mA to 100mARise/Fall Time < 90psAutomatic Average Power Control with Failure
MonitorComplies with ANSI, ITU, and Bellcore
SDH/SONET SpecificationsEnable Control
Ordering Information
MAX3867, 2.5Gbps SDH/SONET Laser Driver
with Automatic Power Control
Typical Operating Circuit
MAX3867
+3.3V, 2.5Gbps SDH/SONET Laser Driver
with Automatic Power ControlELECTRICAL CHARACTERISTICS(VCC= +3.14V to +5.5V, TA= -40°C to +85°C. Typical values are at VCC= +3.3V, IMOD= 30mA, IBIAS= 60mA, and TA= +25°C,
unless otherwise noted.) (Note 1)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
Note 1:Characteristics at -40°C guaranteed by design and characterization. Dice are tested at TA= +25°C only.
Note 2:Tested at RMODSET= 2.49kΩ, RBIASMAX= 1.69kΩ, excluding IBIASand IMOD.
Note 3:Voltage on BIAS pin is (VCC- 1.6V).
Note 4:Both the bias and modulation currents will be switched off if any of the current set pins are grounded.
Note 5:Accuracy refers to part-to-part variation.
Note 6:Assuming that the laser to monitor-diode transfer function does not change with temperature.
Supply Voltage, VCC.............................................-0.5V to +7.0V
Current into BIAS ...........................................-20mA to +150mA
Current into OUT+, OUT-................................-20mA to +100mA
Current into MD.....................................................-5mA to +5mA
Voltage at DATA+, DATA-, CLK+, CLK-,
ENABLE, LATCH, FAIL, SLWSTRT.........-0.5V to (VCC+ 0.5V)
Voltage at APCFILT, CAPC, MODSET,
BIASMAX, APCSET...........................................-0.5V to +3.0V
Voltage at OUT+, OUT-.............................+1.5V to (VCC+ 1.5V)
Voltage at BIAS.........................................+1.0V to (VCC+ 0.5V)
Current into FAIL...............................................-10mA to +30mA
Continuous Power Dissipation (TA= +85°C)
TQFP (derate 20.8mW/°C above +85°C)...................1354mW
Storage Temperature Range.............................-65°C to +165°C
Operating Junction Temperature Range...........-55°C to +150°C
Processing Temperature (die).........................................+400°C
Lead Temperature (soldering, 10sec).............................+300°C
ABSOLUTE MAXIMUM RATINGS
MAX3867
+3.3V, 2.5Gbps SDH/SONET Laser Driver
with Automatic Power ControlELECTRICAL CHARACTERISTICS(VCC= +3.14V to +5.5V, load as shown in Figure 2, TA= -40°C to +85°C. Typical values are at VCC= +3.3V, IMOD= 30mA, and TA=
+25°C.) (Note 7)
Note 7:AC characteristics are guaranteed by design and characterization.
Note 8:Measured with 622Mbps 0-1 pattern, LATCH = high.
Note 9:PWD = (wider pulse - narrower pulse) / 2.
Note 10:See Typical Operating Characteristicsfor worst-case distribution.
MAX3867
+3.3V, 2.5Gbps SDH/SONET Laser Driver
with Automatic Power ControlFigure 1. Required Input Signal and Output Polarity
Figure 3. Setup/Hold Time Definition
Figure 2. Output Termination for Characterization
MAX3867
+3.3V, 2.5Gbps SDH/SONET Laser Driver
with Automatic Power Control
Typical Operating Characteristics (VCC = +3.3V, load as shown in Figure 2, TA= +25°C, unless otherwise noted.)
MAX3867
+3.3V, 2.5Gbps SDH/SONET Laser Driver
with Automatic Power Control
Pin Description
Typical Operating Characteristics (continued)(VCC = +3.3V, load as shown in Figure 2, TA= +25°C, unless otherwise noted.)