MAX1976AETA130+T ,Low-Input-Voltage, 300mA LDO Regulators with RESET in SOT and TDFNMAX1963A/MAX1976A19-3684; Rev 1; 5/12Low-Input-Voltage, 300mA LDO Regulators with RESET in SOT and ..
MAX1976AETA150+T ,Low-Input-Voltage, 300mA LDO Regulators with RESET in SOT and TDFNELECTRICAL CHARACTERISTICS(V = (V + 0.5V) or 1.8V, whichever is greater; SHDN = IN, C = 1µF, C = 4. ..
MAX1976AEZT150+T ,Low-Input-Voltage, 300mA LDO Regulators with RESET in SOT and TDFNFeaturesThe MAX1963A/MAX1976A low-dropout linear regula-♦ Low 1.62V Minimum Input Voltagetors opera ..
MAX1976AEZT180+T ,Low-Input-Voltage, 300mA LDO Regulators with RESET in SOT and TDFNELECTRICAL CHARACTERISTICS(V = (V + 0.5V) or 1.8V, whichever is greater; SHDN = IN, C = 1µF, C = 4. ..
MAX1976ETT150-T ,1.5 V, low-input-voltage, 300 mA LDO regulator with RESETELECTRICAL CHARACTERISTICS(V = (V + 0.5V) or 1.8V, whichever is greater; SHDN = IN, C = 1µF, C = 4. ..
MAX1976EZT085-T ,0.85 V, low-input-voltage, 300 mA LDO regulator with RESETfeatures include logic-controlled shutdown, Tiny 6-Pin Thin SOT23 Package (<1.1mm High)short-circu ..
MAX4951CTP+T ,6Gbps SATA Bidirectional Redriver with Input Equalization, Preemphasis, and Advanced Power Managementfeatures an independent channel dynamic power-down S High Level of Integration for Performancemode ..
MAX495CSA ,Single/Dual/Quad, Micropower, Single-Supply Rail-to-Rail Op AmpsFeatures' Low-Voltage Single-Supply Operation (+2.7V to +6V)The dual MAX492, quad MAX494, and singl ..
MAX495CSA ,Single/Dual/Quad, Micropower, Single-Supply Rail-to-Rail Op AmpsELECTRICAL CHARACTERISTICS(V = 2.7V to 6V, V = GND, V = 0V, V = V / 2, T = +25°C, unless otherwise ..
MAX495CSA ,Single/Dual/Quad, Micropower, Single-Supply Rail-to-Rail Op AmpsGeneral Description ________
MAX495CSA+ ,Single/Dual/Quad, Micropower, Single-Supply, Rail-to-Rail Op AmpsFeatures♦ Low-Voltage Single-Supply Operation (+2.7V to +6V)The dual MAX492, quad MAX494, and singl ..
MAX495CSA-T ,Single/Dual/Quad, Micropower, Single-Supply, Rail-to-Rail Op Amps Not Recommended for New Designs The MAX495 was manufactured for Maxim by an outside wafer foundr ..
MAX1963AEZT090+T-MAX1976AETA130+T-MAX1976AETA150+T-MAX1976AEZT150+T-MAX1976AEZT180+T
Low-Input-Voltage, 300mA LDO Regulators with RESET in SOT and TDFN
General DescriptionThe MAX1963A/MAX1976A low-dropout linear regula-
tors operate from a +1.62V to +3.6V supply and deliver
a guaranteed 300mA continuous load current with a low
100mV dropout. The high-accuracy (±0.5%) output
voltage is preset to an internally trimmed voltage in the
+0.75V to +3.0V range. An active-low, open-drain reset
output remains asserted for at least 2.2ms (MAX1963A)
or 70ms (MAX1976A) after the output voltage reaches
regulation. These devices are offered in thin SOT23 and
thin DFN packages. An internal pMOS pass transistor
allows the low supply current to remain independent of
load and dropout voltage, making these devices ideal for
portable battery-powered equipment.
ApplicationsNotebook/Handheld Computers
Cellular/Smart/PDA Phones
DSC, CD/MP3 Players
PCMCIA Cards
FeaturesLow 1.62V Minimum Input VoltageGuaranteed 300mA Output Current±2.5% Accuracy Over Load/Line/TempLow 100mV Dropout at 300mA Load2.2ms (MAX1963A) or 70ms (MAX1976A) RESET
Output FlagSupply Current Independent of Load and
Dropout VoltageLogic-Controlled ShutdownThermal-Overload and Short-Circuit ProtectionPreset Output Voltages (0.75V to 3.0V)Tiny 6-Pin Thin SOT23 Package (<1.1mm High)TDFN Package (<0.8mm High)
MAX1963A/MAX1976A
Low-Input-Voltage, 300mA LDO Regulators
with RESETin SOT and TDFN
Ordering Information19-3684; Rev 1; 5/12
PART*TEMP RANGEPIN-PACKAGEA X1 9 6 3 A E Z T_ _ _+ T-40°C to +85°C6 Thin SOT23-6
MAX1963AETT_ _ _+T-40°C to +85°C6 TD FN -6 3mm x 3m m AX 1963AE TA_ _ _+ T-40°C to +85°C8 TD FN -8 2mm x 2m m
A X1 9 7 6 A E Z T_ _ _+ T-40°C to +85°C6 Thin SOT23-6AX 1976AE TT_ _ _+ T-40°C to +85°C6 TD FN -6 3mm x 3m m AX 1976AE TA_ _ _+ T-40°C to +85°C8 TD FN -8 2mm x 2m m
MAX1976AETT_ _ _/V+T-40°C to +85°C6 TD FN -6 3mm x 3m m
TOP VIEW
TDFN
3mm x 3mmI.C.
OUT
RESET
GNDIN
SHDN34
MAX1963A
MAX1976A
GND
RESETSHDN
OUTIN
MAX1963A
MAX1976A
THIN SOT234
I.C.5
TDFN
2mm x 2mmN.C.
I.C.
OUT
N.C.IN
SHDN3
RESET6
GND
MAX1963A
MAX1976A
Pin Configurations*Insert the desired three-digit suffix (see the Selector Guide) into
the blanks to complete the part number. Contact the factory for
other output voltages.
MAX1963A
MAX1976A
INPUT
1.62V TO 3.6V
COUT
4.7μF
OFFCIN
1μF
UP TO
300mA
SHDN
GND
OUTPUT
0.75V TO 3.0V
LOGIC
SUPPLY
100kΩ
TO μC
OUT
RESET
Typical Operating Circuit+Denotes a lead(Pb)-free/RoHS-compliant package.
/V denotes an automotive-qualified part.
MAX1963A/MAX1976A
Low-Input-Voltage, 300mA LDO Regulators
with RESETin SOT and TDFN
ABSOLUTE MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS(VIN= (VOUT+ 0.5V) or 1.8V, whichever is greater; SHDN= IN, CIN= 1µF, COUT= 4.7µF, TA= -40°C to +85°C, unless otherwise
noted. Typical values are at TA= +25°C.) (Note 1)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
IN, SHDN, RESETto GND.....................................-0.3V to +4.0V
OUT to GND................................................-0.3V to (VIN+ 0.3V)
Output Short-Circuit Duration.....................................Continuous
Continuous Power Dissipation (multilayer board, TA= +70°C)
6-Pin SOT23 (derate 9.1mW/°C above +70°C)............727mW
6-Pin TDFN (derate 23.8mW/°C above +70°C)......1904.8mW
8-Pin TDFN (derate 11.9mW/°C above +70°C)........953.5mW
Operating Temperature Range...........................-40°C to +85°C
Junction Temperature.....................................................+150°C
Storage Temperature Range.............................-65°C to +150°C
Lead Temperature (soldering, 10s).................................+300°C
Soldering Temperature (reflow).......................................+260°C
PARAMETERSYMBOLCONDITIONSMINTYPMAXUNITSInput VoltageVIN1.623.60V
Input Undervoltage LockoutVUVLOVIN rising or falling
(180mV typical hysteresis)1.301.60V
Output Voltage AccuracyIOUT = 1mA to 300mA,
VIN = (VOUT + 0.5V) to +3.6V-2.5±0.5+2.5%
Maximum Output CurrentIOUTContinuous300mARMS
Current LimitILIMVOUT = 96% of nominal value450550650mA
No load70140
IOUT = 300mA90Ground CurrentIQ
Dropout (Note 2)70
Dropout VoltageVIN - VOUTIOUT = 300mA, VOUT ≥ 1.8V (Note 2)100200mV
Load Regulation∆VLDRIOUT = 1mA to 300mA0.020.3%
Line Regulation∆VLNRVIN = (VOUT + 0.5V) to +3.6V, IOUT = 1mA-0.15+0.01+0.15% / V
Output Noise10Hz to 100kHz, IOUT = 10mA, VOUT = 1.5V86µVRMS
PSRRf < 1kHz, IOUT = 10mA70dB
SHUTDOWNTA = +25°C0.0011Shutdown Supply CurrentIOFFSHDN = GNDTA = +85°C0.01µA
VIHVIN = 1.62V to 3.6V1.4SHDN Input Logic LevelsVILVIN = 1.62V to 3.6V0.6V
TA = +25°C1100SHDN Input Bias CurrentISHDNVSHDN = 0V or 3.6VTA = +85°C5nA
Turn-On DelayFrom SHDN high to OUT high, VOUT = 1.8V90µs
MAX1963A/MAX1976A
Low-Input-Voltage, 300mA LDO Regulators
with RESETin SOT and TDFN
Note 1:Limits are 100% production tested at TA= +25°C. Limits over the operating temperature range are guaranteed by design.
Note 2:The dropout voltage is defined as VIN- VOUT, when VOUTis 4% lower than the value of VOUTwhen VIN = VOUT+ 0.5V.
PARAMETERSYMBOLCONDITIONSMINTYPMAXUNITSRESET OUTPUT
Reset Threshold AccuracyVOUT falling (1.7% typical hysteresis)8082.585%VOUT
I RESET = 100µA1100RESET Output Low VoltageVOLVIN = +1.0V, I RESET = 100µA30400mV
TA = +25°C0.0011RESET Output High LeakageIOHV RESET = 3.6V,
RESET not assertedTA = +85°C0.01µA
MAX1963A2.23.25.5Reset DelaytRPFrom VOUT high to RESET
risingMAX1976A70100160ms
THERMAL PROTECTIONThermal-Shutdown TemperatureT SHDN+165°C
Thermal-Shutdown Hysteresis∆T SHDN15°C
Typical Operating Characteristics(VIN= (VOUT+ 0.5V) or 1.8V, whichever is greater; SHDN= IN, CIN= 1µF, COUT= 4.7µF, TA= +25°C, unless otherwise noted.)
OUTPUT VOLTAGE ACCURACY
vs. LOAD CURRENTMAX1963/76 toc01
LOAD CURRENT (mA)
OUTPUT VOLTAGE ACCURACY (%)
VOUT = +3.0VVOUT = +1.5V
VOUT = +0.75V
OUTPUT VOLTAGE ACCURACY
vs. INPUT VOLTAGEMAX1963/76 toc02
INPUT VOLTAGE (V)
OUTPUT VOLTAGE ACCURACY (%)
IOUT = 300mA
IOUT = 100mA
IOUT = 0mA
VOUT = 1.5V
OUTPUT VOLTAGE ACCURACY
vs. TEMPERATUREMAX1963/76 toc03
TEMPERATURE (°C)
OUTPUT VOLTAGE ACCURACY (%)3510-15
VOUT = +1.5V
IOUT = 0mA, 100mA, 300mA
ELECTRICAL CHARACTERISTICS (continued)(VIN= (VOUT+ 0.5V) or 1.8V, whichever is greater; SHDN= IN, CIN= 1µF, COUT= 4.7µF, TA= -40°C to +85°C, unless otherwise
noted. Typical values are at TA= +25°C.) (Note 1)
MAX1963A/MAX1976A
Low-Input-Voltage, 300mA LDO Regulators
with RESETin SOT and TDFN
GROUND-PIN CURRENT
vs. LOAD CURRENTMAX1963/76 toc04
LOAD CURRENT (mA)
GROUND-PIN CURRENT (
VOUT = +3.0V
VOUT = +0.75V
VOUT = +1.5V
GROUND-PIN CURRENT
vs. INPUT VOLTAGEMAX1963/76 toc05
INPUT VOLTAGE (V)
GROUND-PIN CURRENT (
IOUT = 100mA
IOUT = 300mA
IOUT = 0mA
VOUT = 1.5V
GROUND-PIN CURRENT
vs. TEMPERATUREMAX1963/76 toc06
TEMPERATURE (°C)
GROUND-PIN CURRENT (40200-20
IOUT = 100mA
IOUT = 300mA
IOUT = 0mA
DROPOUT VOLTAGE
vs. LOAD CURRENTMAX1963/76 toc07
LOAD CURRENT (mA)
DROPOUT
(mV)
VOUT = +1.8V
VOUT = +3.0V
POWER-SUPPLY REJECTION RATIO
vs. FREQUENCYMAX1963/76 toc08
FREQUENCY (kHz)
PSRR (dB)
VOUT = +0.75V
VOUT = +1.5V
VOUT = +3.0V
IOUT = 10mA
LINE-TRANSIENT RESPONSEMAX1963/76 toc09
40μs/div
VIN500mV/div
1.5V
10mV/div
AC-COUPLED
VOUT
3.5V
Typical Operating Characteristics (continued)(VIN= (VOUT+ 0.5V) or 1.8V, whichever is greater; SHDN= IN, CIN= 1µF, COUT= 4.7µF, TA= +25°C, unless otherwise noted.)
LINE-TRANSIENT RESPONSE
NEAR DROPOUTMAX1963/76 toc10
40μs/div
VIN500mV/div
1.5V
10mV/div
AC-COUPLED
VOUT
1.8V
MAX1963A/MAX1976A
Low-Input-Voltage, 300mA LDO Regulators
with RESETin SOT and TDFN
LOAD-TRANSIENT RESPONSEMAX1963/76 toc11
20μs/div
200mA/div
20mV/div
AC-COUPLED
200mA
VOUT
IOUT
20mA
VIN = 3.6V
VOUT = 1.5V
LOAD-TRANSIENT RESPONSE
NEAR DROPOUTMAX1963/76 toc12
20μs/div
200mA/div
20mV/div
AC-COUPLED
200mA
VOUT
VIN = 1.8V
VOUT = 1.5V
IOUT
20mA
ypical Operating Characteristics (continued)(VIN= (VOUT+ 0.5V) or 1.8V, whichever is greater; SHDN= IN, CIN= 1µF, COUT= 4.7µF, TA= +25°C, unless otherwise noted.)
SHUTDOWN RESPONSEMAX1963/76 toc13
100μs/div
1V/div
500mV/div
VOUT
VSHDN
MAX1963/76 toc14
40ms/div
1V/div
1V/div
1V/div
VOUT
VSHDN
VRESET
MAX1976
SHUTDOWN/RESET RESPONSEMAX1963/76 toc15
2V/div
1V/div
1V/divVOUT
VIN
VRESET
MAX1976
LINE/RESET RESPONSE
MAX1963A/MAX1976A
Low-Input-Voltage, 300mA LDO Regulators
with RESETin SOT and TDFN
Pin Description
PIN
THIN
SOT23
6-PIN
TDFN
(3mm x 3mm)
8-PIN
TDFN
(2mm x 2mm)
NAMEFUNCTION8IN
Regulator Input. Supply voltage can range from +1.62V to +3.6V. Bypass IN
with at least a 1µF ceramic capacitor to GND (see the Capacitor Selection and
Regulator Stability section).——GNDGround. GND also functions as a heatsink. Solder to a large pad or circuit-
board ground plane to maximize SOT23 power dissipation.45GNDGround6SHDNActive-Low Shutdown Input. A logic-low reduces supply current to below 1µA.
Connect to IN or logic-high for normal operation.4RESET
Open-Drain, Active-Low Reset Output. RESET rises 3.2ms (MAX1963A) or
100ms (MAX1976A) after the output has achieved regulation. RESET falls
immediately if VOUT drops below 82.5% of its nominal voltage, or if the
MAX1963A/MAX1976A are shut down.23I.C.Internally Connected. Leave unconnected or connect to GND.11OUTRegulator Output. Sources up to 300mA. Bypass with a 4.7µF low-ESR
ceramic capacitor to GND.—2, 7N.C.No Connection. Not internally connected.—EPGround (TDFNs only). EP also functions as a heatsink. Solder EP to a large
pad or circuit-board ground plane to maximize TDFN power dissipation.
MAX1963A
MAX1976A
GND
SHDN
SHUTDOWN
LOGIC
THERMAL
SENSORREF82.5%
REF
TIMER
ERROR
AMP
MOS DRIVER
WITH ILIMIT
OUT
RESET