MAX1490EBEPG ,15kV ESD-Protected, Isolated RS-485/RS-422ELECTRICAL CHARACTERISTICS(V = +5V ±10%, V = V , T = T to T , unless otherwise noted. Typical value ..
MAX1490EBEPG ,15kV ESD-Protected, Isolated RS-485/RS-422ApplicationsD2 4 21 ISO RO DRVIndustrial-Control Local Area Networks5GND1 20 AAutomatic Test Equipm ..
MAX1496EAI ,3.5-digit, single-chip ADC with LED driverApplications Ordering InformationDigital Panel MetersPIN- RESOLUTIONPART TEMP RANGEHand-Held Meters ..
MAX1496EPI+ ,3.5- and 4.5-Digit, Single-Chip ADCs with LED DriversApplications Ordering InformationDigital Panel MetersPIN- RESOLUTIONPART TEMP RANGEHand-Held Meters ..
MAX14998ETO+ ,Two-Lane and Four-Lane DisplayPort Passive Switches with Separate AUX/HPD ControlApplications*EP = Exposed pad.Notebook PCsTypical Operating Circuit appears at end of data sheet.De ..
MAX149ACAP ,+2.7V to +5.25V / Low-Power / 8-Channel / Serial 10-Bit ADCsGeneral Description ________
MAX412 ,Single/Dual/Quad, 28MHz, Low-Noise, Low-Voltage, Precision Op AmpsApplicationsMAX410EPA -40°C to +85°C 8 Plastic DIPLow-Noise Frequency Synthesizers MAX410BEPA -40°C ..
MAX4120ESD ,Single/Dual/Quad / 400MHz / Low-Power / Current Feedback AmplifiersGeneral Description ________
MAX4121CSA ,330MHz Buffered Video Switches/ Crosspoint Building Blocksfeaturesinclude -92dB crosstalk and -78dB isolation (MAX4121).' Ultra-Low Switching GlitchThe MAX41 ..
MAX4122EUK ,Single/Dual/Quad / Wide-Bandwidth / Low-Power / Single-Supply Rail-to-Rail I/O Op AmpsELECTRICAL CHARACTERISTICS (continued)(V = +2.7V to +6.5V, V = 0V, V = 0V, V = V /2, R tied to V /2 ..
MAX4122EUK+T ,Single/Dual/Quad, Wide-Bandwidth, Low-Power, Single-Supply Rail-to-Rail I/O Op AmpsMAX4122–MAX412919-1087; Rev 1; 8/97Single/Dual/Quad, Wide-Bandw idth, Low -Pow er,Single-Supply Rai ..
MAX4122EUK-T ,Single/Dual/Quad, Wide-Bandwidth, Low-Power, Single-Supply Rail-to-Rail I/O Op AmpsFeaturesThe MAX4122–MAX4129 family of operational amplifiers♦ 5-Pin SOT23 Package (MAX4122/4)combin ..
MAX1480ECEPI-MAX1490EAEPG-MAX1490EBEPG
15kV ESD-Protected, Isolated RS-485/RS-422
_________________General DescriptionThe MAX1480EA/MAX1480EC/MAX1490EA/MAX1490EB
are complete, electrically isolated, RS-485/RS-422 data
communications interface solutions in a hybrid microcir-
cuit. The RS-485/RS-422 I/O pins are protected against
±15kV electrostatic discharge (ESD) shocks, without
latchup. Transceivers, optocouplers, and a transformer
provide a complete interface in a standard DIP package.
A single +5V supply on the logic side powers both sides
of the interface.
The MAX1480EC/MAX1490EB feature reduced-slew-rate
drivers that minimize EMI and reduce reflections caused
by improperly terminated cables, allowing error-free data
transmission at data rates up to 160kbps. The
MAX1480EA/MAX1490EA driver slew rate is not limited,
allowing transmission rates up to 2.5Mbps. The
MAX1480EA/MAX1480EC are designed for half-duplex
communication, while the MAX1490EA/MAX1490EB fea-
ture full-duplex communication.
Drivers are short-circuit current limited and protected
against excessive power dissipation by thermal shut-
down circuitry that places the driver outputs into a high-
impedance state. The receiver input has a fail-safe
feature that guarantees a known output (ROlow for the
MAX1480EA/MAX1480EC, RO high for the MAX1490EA/
MAX1490EB) if the input is open circuit.
The MAX1480EA/MAX1480EC/MAX1490EA/MAX1490EB
withstand 1260VRMS(1min) or 1520VRMS(1s). Their iso-
lated outputs meet all RS-485/RS-422 specifications. The
MAX1480EA/MAX1480EC are available in a 28-pin DIP
package, and the MAX1490EA/MAX1490EB are available
in a 24-pin DIP package.
________________________ApplicationsIsolated RS-485/RS-422 Data Interface
Transceivers for EMI-Sensitive Applications
Industrial-Control Local Area Networks
Automatic Test Equipment
HVAC/Building Control Networks
Telecom
____________________________FeaturesIsolated Data Interface, Guaranteed to 1260VRMS
(1min)±15kVESD Protection on I/O PinsSlew-Rate Limited for Errorless Data
Transmission (MAX1480EC/MAX1490EB)High-Speed, Isolated, 2.5Mbps RS-485/RS-422
Interface (MAX1480EA/MAX1490EA)Full-Duplex Data Communication
(MAX1490EA/MAX1490EB)Single +5V SupplyCurrent Limiting and Thermal Shutdown for
Driver Overload ProtectionStandard 0.6in DIP Packages
28-Pin DIP (MAX1480EA/MAX1480EC)
24-Pin DIP (MAX1490EA/MAX1490EB)
MAX1480E/MAX1490E
±15kV ESD-Protected, Isolated RS-485/RS-422
Data Interfaces
Pin Configurations19-1940; Rev 0; 4/01
Selector Guide appears at end of data sheet.
MAX1480E/MAX1490E
±15kV ESD-Protected, Isolated RS-485/RS-422
Data Interfaces
ABSOLUTE MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS
(VCC_= +5V ±10%, VFS= VCC_, TA= TMINto TMAX, unless otherwise noted. Typical values are at VCC_= +5V and TA= +25°C.)
(Notes 1, 2)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
With Respect to GND_
Supply Voltage (VCC_)..........................................-0.3V to +6V
Control Input Voltage (SD, FS)..............-0.3V to (VCC_+ 0.3V)
Receiver Output Voltage (RO, RO).......-0.3V to (VCC_+ 0.3V)
Output Switch Voltage (D1, D2).......................................+12V
With Respect to ISO COM_
Control Input Voltage (ISO DE_)....-0.3V to (ISO VCC_+ 0.3V)
Driver Input Voltage (ISO DI_).......-0.3V to (ISO VCC_+ 0.3V)
Receiver Output Voltage (ISO RO_)..-0.3V to (ISO VCC_+ 0.3V)
Driver Output Voltage (A, B, Y, Z)......................-8V to +12.5V
Receiver Input Voltage (A, B).............................-8V to +12.5V
LED Forward Current (DI, DE, ISO RO LED)......................50mA
Continuous Power Dissipation (TA= +70°C)
24-Pin Plastic DIP (derate 8.7mW°C above +70°C)....696mW
28-Pin Plastic DIP (derate 9.09mW/°C above +70°C).727mW
Operating Temperature Ranges
MAX1480E_CPI/MAX1490E_CPI........................0°C to +70°C
MAX1480E_EPI/MAX1490E_EPI......................-40°C to +85°C
Storage Temperature Range.............................-65°C to +150°C
Lead Temperature (soldering, 10s).................................+300°C
MAX1480E/MAX1490E
±15kV ESD-Protected, Isolated RS-485/RS-422
Data Interfaces
ELECTRICAL CHARACTERISTICS (continued)
(VCC_= +5V ±10%, VFS= VCC_, TA= TMINto TMAX, unless otherwise noted. Typical values are at VCC_= +5V and TA= +25°C.)
(Notes 1, 2)
SWITCHING CHARACTERISTICS—MAX1480EA/MAX1490EA
(VCC_= +5V ±10%, VFS= VCC_, TA= TMINto TMAX, unless otherwise noted. Typical values are at VCC_= +5V and TA= +25°C.)
MAX1480E/MAX1490E
±15kV ESD-Protected, Isolated RS-485/RS-422
Data Interfaces
Note 1:All currents into device pins are positive; all currents out of device pins are negative. All voltages are referenced to logic-
side ground (GND_), unless otherwise specified.
Note 2:For DE´and DI´pin descriptions, see Detailed Block Diagram and Typical Application Circuit (Figure 1 for MAX1480EA/
MAX1480EC, Figure 2 for MAX1490EA/MAX1490EB).
Note 3:Shutdown supply current is the current at VCC1and VCC2when shutdown is enabled.
Note 4:Limit guaranteed by applying 1520VRMSfor 1s. Test voltage is applied between all pins on one side of the package to all
pins on the other side of the package, e.g., between pins 1–14 and pins 15–28 on the 28-pin package.
Note 5:Applies to peak current (see Typical Operating Characteristics). Although the MAX1480EA/MAX1480EC and
MAX1490EA/MAX1490EB provide electrical isolation between logic ground and signal paths, they do not provide isolation
between external shields and the signal paths (see Isolated Common Connectionsection).
SWITCHING CHARACTERISTICS—MAX1480EA/MAX1490EA (continued)
(VCC_= +5V ±10%, VFS= VCC_, TA= TMINto TMAX, unless otherwise noted. Typical values are at VCC_= +5V and TA= +25°C.)
SWITCHING CHARACTERISTICS—MAX1480EC/MAX1490EB
(VCC_= +5V ±10%, VFS= VCC_, TA= TMINto TMAX, unless otherwise noted. Typical values are at VCC_= +5V and TA= +25°C.)
MAX1480E/MAX1490E
±15kV ESD-Protected, Isolated RS-485/RS-422
Data Interfaces
OUTPUT CURRENT vs.
RECEIVER OUTPUT LOW VOLTAGE
MAX1480E/90E TOC01
OUTPUT LOW VOLTAGE (V)
OUTPUT CURRENT (mA)
OUTPUT CURRENT vs.
RECEIVER OUTPUT HIGH VOLTAGEMAX1480E/90E TOC02
OUTPUT HIGH VOLTAGE (V)
OUTPUT CURRENT (mA)
RECEIVER OUTPUT HIGH VOLTAGE
vs. TEMPERATURE
MAX1480E/90E TOC03
TEMPERATURE (°C)
OUTPUT HIGH VOLTAGE (V)-20604080
RECEIVER OUTPUT LOW VOLTAGE
vs. TEMPERATURE
MAX1480E/90E TOC04
TEMPERATURE (°C)
OUTPUT LOW VOLTAGE (V)-20604080
DRIVER OUTPUT CURRENT
vs. DIFFERENTIAL OUTPUT VOLTAGE
MAX1480E/90E TOC07
DIFFERENTIAL OUTPUT VOLTAGE (V)
OUTPUT CURRENT (mA)
OUTPUT CURRENT vs.
DRIVER OUTPUT LOW VOLTAGE
MAX1480E/90E TOC05
OUTPUT LOW VOLTAGE (V)
OUTPUT CURRENT (mA)
OUTPUT CURRENT vs.
DRIVER OUTPUT HIGH VOLTAGE
MAX1480E/90E TOC06
OUTPUT HIGH VOLTAGE (V)
OUTPUT CURRENT (mA)
DRIVER DIFFERENTIAL OUTPUT VOLTAGE
vs. TEMPERATURE
MAX1480E/90E TOC08
TEMPERATURE (°C)
DIFFERENTIAL OUTPUT VOLTAGE (V)-20604080
SHUTDOWN CURRENT
vs. TEMPERATURE
MAX1480E/90E TOC09
TEMPERATURE (°C)
SHUTDOWN CURRENT (-20604080
__________________________________________Typical Operating Characteristics
(VCC_= +5V, VFS= VCC_, Figures 1 and 2, TA = +25°C, unless otherwise noted.)
