MAX1249BCEE ,+2.7V to +5.25V, Low-Power, 4-Channel, Serial 10-Bit ADCs in QSOP-16MAX1248/MAX124919-1072; Rev 2; 5/98+2.7V to +5.25V, Low-Power, 4-Channel,Serial 10-Bit ADCs in QSOP ..
MAX1249BCPE ,+2.7V to +5.25V, Low-Power, 4-Channel, Serial 10-Bit ADCs in QSOP-16General Description ________
MAX1249BEEE ,+2.7V to +5.25V, Low-Power, 4-Channel, Serial 10-Bit ADCs in QSOP-16Applications __________Typical Operating CircuitPortable Data Logging Data Acquisition+3VMedical In ..
MAX12527ETK+ ,Dual, 65Msps, 12-Bit, IF/Baseband ADCApplications(Msps) (Bits)IF and Baseband Communication ReceiversMAX12557 65 14Cellular, LMDS, Point ..
MAX1253BEUE ,Stand-Alone, 10-Channel, 12-Bit System Monitors with Internal Temperature Sensor and VDD MonitorELECTRICAL CHARACTERISTICS(V = +2.7V to +3.6V (MAX1253), V = +4.5V to +5.5V (MAX1254), V = +2.5V (M ..
MAX1253BEUE+T ,Stand-Alone, 10-Channel, 12-Bit System Monitors with Internal Temperature Sensor and VDD MonitorApplications Ordering InformationSystem SupervisionPART TEMP RANGE PIN-PACKAGERemote Telecom Networ ..
MAX3679CTJ+ , 3.3V, Low-Jitter Crystal to LVPECL Clock Generator
MAX367CWN ,Signal-Line Circuit ProtectorsGeneral Description ________
MAX367EWN ,Signal-Line Circuit ProtectorsFeaturesThe MAX366 and MAX367 are multiple, two-terminal circuit' ±40V Overvoltage Protectionprotec ..
MAX367EWN ,Signal-Line Circuit ProtectorsApplicationsMAX367 available after January 1, 1995.* Dice are tested at T = +25°C only.Process Cont ..
MAX367EWN+ ,Signal Line Circuit Protector with Three Independent ProtectorsMAX366/MAX36719-0326; Rev 0; 12/94Signal-Line Circuit Protectors_______________
MAX3680EAI ,+3.3V / 622Mbps / SDH/SONET 1:8 Deserializer with TTL OutputsELECTRICAL CHARACTERISTICS(V = +3.0V to +3.6V, T = -40°C to +85°C, unless otherwise noted. Typical ..
MAX1248ACEE-MAX1248AEEE-MAX1248BCEE-MAX1248BEEE-MAX1249ACEE-MAX1249AEEE-MAX1249BCEE-MAX1249BCPE-MAX1249BEEE-MAX125CCAX-MAX125CEAX-MAX126CCAX-MAX126CEAX
2x4-Channel, Simultaneous-Sampling 14-Bit DAS
_______________General DescriptionThe MAX1248/MAX1249 10-bit data-acquisition sys-
tems combine a 4-channel multiplexer, high-bandwidth
track/hold, and serial interface with high conversion
speed and low power consumption. They operate from
a single +2.7V to +5.25V supply, and their analog
inputs are software configurable for unipolar/bipolar
and single-ended/differential operation.
The 4-wire serial interface connects directly to SPI™/
QSPI™ and MICROWIRE™ devices without external
logic. A serial strobe output allows direct connection
to TMS320-family digital signal processors. The
MAX1248/MAX1249 use either the internal clock or an
external serial-interface clock to perform successive-
approximation analog-to-digital conversions.
The MAX1248 has an internal 2.5V reference, while the
MAX1249 requires an external reference. Both parts
have a reference-buffer amplifier with a ±1.5% voltage
adjustment range.
These devices provide a hard-wired SHDNpin and a
software-selectable power-down, and can be pro-
grammed to automatically shut down at the end of a
conversion. Accessing the serial interface automatically
powers up the MAX1248/MAX1249, and the quick
turn-on time allows them to be shut down between all
conversions. This technique can cut supply current to
under 60µA at reduced sampling rates.
The MAX1248/MAX1249 are available in a 16-pin DIP
and a very small QSOP that occupies the same board
area as an 8-pin SO.
For 8-channel versions of these devices, see the
MAX148/MAX149 data sheet.
________________________ApplicationsPortable Data LoggingData Acquisition
Medical InstrumentsBattery-Powered Instruments
Pen DigitizersSystem Supervision
____________________________Features4-Channel Single-Ended or 2-Channel
Differential InputsSingle +2.7V to +5.25V OperationInternal 2.5V Reference (MAX1248)Low Power:1.2mA (133ksps, +3V supply)
54µA (1ksps, +3V supply)
1µA (power-down mode)SPI/QSPI/MICROWIRE/TMS320-Compatible
4-Wire Serial InterfaceSoftware-Configurable Unipolar or Bipolar Inputs16-Pin QSOP Package (same area as 8-pin SO)
MAX1248/MAX1249
+2.7V to +5.25V, Low-Power, 4-Channel,
Serial 10-Bit ADCs in QSOP-1619-1072; Rev 2; 5/98
Pin Configuration appears at end of data sheet.SPI and QSPI are trademarks of Motorola, Inc.
MICROWIREis a trademark of National Semiconductor Corp.
__________Typical Operating Circuit
MAX1248/MAX1249
+2.7V to +5.25V, Low-Power, 4-Channel,
Serial 10-Bit ADCs in QSOP-16
ABSOLUTE MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS(VDD= +2.7V to +5.25V; COM = 0V; fSCLK= 2.0MHz; external clock (50% duty cycle); 15 clocks/conversion cycle (133ksps);
MAX1248—4.7µF capacitor at VREF pin; MAX1249—external reference, VREF = 2.500Vapplied to VREF pin; TA= TMINto TMAX,
unless otherwise noted.)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
VDDto AGND, DGND..............................................-0.3V to +6V
AGND to DGND....................................................-0.3V to +0.3V
CH0–CH3, COM to AGND, DGND............-0.3V to (VDD+ 0.3V)
VREF to AGND...........................................-0.3V to (VDD+ 0.3V)
Digital Inputs to DGND............................................-0.3V to +6V
Digital Outputs to DGND...........................-0.3V to (VDD+ 0.3V)
Digital Output Sink Current.................................................25mA
Continuous Power Dissipation (TA= +70°C)
Plastic DIP (derate 10.53mW/°C above +70°C).........842mW
QSOP (derate 8.30mW/°C above +70°C)...................667mW
CERDIP (derate 10.00mW/°C above +70°C)..............800mW
Operating Temperature Ranges
MAX1248_C_E/MAX1249_C_E..........................0°C to +70°C
MAX1248_E_E/MAX1249_E_E........................-40°C to +85°C
MAX1248_MJE/MAX1249_MJE....................-55°C to +125°C
Storage Temperature Range............................-60°C to +150°C
Lead Temperature (soldering, 10sec)............................+300°C
MAX1248/MAX1249
+2.7V to +5.25V, Low-Power, 4-Channel,
Serial 10-Bit ADCs in QSOP-16
ELECTRICAL CHARACTERISTICS (continued)(VDD= +2.7V to +5.25V; COM = 0V; fSCLK= 2.0MHz; external clock (50% duty cycle); 15 clocks/conversion cycle (133ksps);
MAX1248—4.7µF capacitor at VREF pin; MAX1249—external reference, VREF = 2.500Vapplied to VREF pin; TA= TMINto TMAX,
unless otherwise noted.)
MAX1248/MAX1249
+2.7V to +5.25V, Low-Power, 4-Channel,
Serial 10-Bit ADCs in QSOP-16
ELECTRICAL CHARACTERISTICS (continued)(VDD= +2.7V to +5.25V; COM = 0V; fSCLK= 2.0MHz, external clock (50% duty cycle); 15 clocks/conversion cycle (133ksps);
MAX1248—4.7µF capacitor at VREF pin; MAX1249—external reference; VREF = 2.500Vapplied to VREF pin, TA= TMINto TMAX,
unless otherwise noted.)
MAX1248/MAX1249
+2.7V to +5.25V, Low-Power, 4-Channel,
Serial 10-Bit ADCs in QSOP-16
TIMING CHARACTERISTICS(VDD= +2.7V to +5.25V, TA= TMINto TMAX, unless otherwise noted.)
Note 1:Tested at VDD= 2.7V; COM = 0V; unipolar single-ended input mode.
Note 2:Relative accuracy is the deviation of the analog value at any code from its theoretical value after the full-scale range has
been calibrated.
Note 3:MAX1248—internal reference, offset nulled; MAX1249—external reference (VREF = +2.500V), offset nulled.
Note 4:Ground “on” channel; sine wave applied to all “off” channels.
Note 5:Conversion time defined as the number of clock cycles multiplied by the clock period; clock has 50% duty cycle.
Note 6:The common-mode range for the analog inputs is from AGND to VDD.
Note 7Sample tested to 0.1% AQL.
Note 8:External load should not change during conversion for specified accuracy.
Note 9:ADC performance is limited by the converter’s noise floor, typically 300µVp-p.
Note 10Guaranteed by design. Not subject to production testing.
Note 11:The MAX1249 typically draws 400mA less than the values shown.
Note 12:Measured as |VFS(2.7V) - VFS(5.25V)|.
MAX1248/MAX1249
+2.7V to +5.25V, Low-Power, 4-Channel,
Serial 10-Bit ADCs in QSOP-16
__________________________________________Typical Operating Characteristics(VDD= 3.0V, VREF = 2.500V, fSCLK= 2.0MHz, CLOAD= 20pF, TA= +25°C, unless otherwise noted.)
MAX1248/MAX1249
+2.7V to +5.25V, Low-Power, 4-Channel,
Serial 10-Bit ADCs in QSOP-16
______________________________________________________________Pin Description
MAX1248/MAX1249
+2.7V to +5.25V, Low-Power, 4-Channel,
Serial 10-Bit ADCs in QSOP-16
_______________Detailed DescriptionThe MAX1248/MAX1249 analog-to-digital converters
(ADCs) use a successive-approximation conversion
technique and input track/hold (T/H) circuitry to convert
an analog signal to a 10-bit digital output. A flexible
serialinterface provides easy interface to microproces-
sors (µPs). Figure 3 is a block diagram of the
MAX1248/MAX1249.
Pseudo-Differential InputThe sampling architecture of the ADC’s analog com-
parator is illustrated in the equivalent input circuit
(Figure 4). In single-ended mode, IN+ is internally
switched to CH0–CH3, and IN-is switched to COM. In
differential mode, IN+ and IN-are selected from two
pairs: CH0/CH1 and CH2/CH3. Configure the channels
with Tables 2 and 3. Please note that the codes for
CH0–CH3 in the MAX1248/MAX1249 correspond to
the codes for CH2–CH5 in the eight-channel
(MAX148/MAX149) versions.
In differential mode, IN-and IN+ are internally switched
to either of the analog inputs. This configuration is
pseudo-differential to the effect that only the signal at
IN+ is sampled. The return side (IN-) must remain sta-
ble within ±0.5LSB (±0.1LSB for best results) with
respect to AGND during a conversion. To accomplish
this, connect a 0.1µF capacitor from IN-(the selected
analog input) to AGND.
During the acquisition interval, the channel selected as
the positive input (IN+) charges capacitor CHOLD. The
acquisition interval spans three SCLK cycles and ends
on the falling SCLK edge after the last bit of the input
control word has been entered. At the end of the acqui-
sition interval, the T/H switch opens, retaining charge
on CHOLDas a sample of the signal at IN+.
The conversion interval begins with the input multiplex-
er switching CHOLDfrom the positive input (IN+) to the
negative input (IN-). In single-ended mode, IN-is sim-
ply COM. This unbalances node ZERO at the compara-
tor’s input. The capacitive DAC adjusts during the
remainder of the conversion cycle to restore node
ZERO to 0V within the limits of 10-bit resolution. This
action is equivalent to transferring a charge of 16pF x
[(VIN+) -(VIN-)] from CHOLDto the binary-weighted
capacitive DAC, which in turn forms a digital represen-
tation of the analog input signal.
Track/HoldThe T/H enters its tracking mode on the falling clock
edge after the fifth bit of the 8-bit control word has been
shifted in. It enters its hold mode on the falling clock
edge after the eighth bit of the control word has been
shifted in. If the converter is set up for single-ended
inputs, IN-is connected to COM, and the converter
samples the “+” input. If the converter is set up for dif-
ferential inputs, IN-connects to the “-” input, and the
difference of |IN+ -IN-|is sampled. At the end of the
conversion, the positive input connects back to IN+,
and CHOLDcharges to the input signal.
The time required for the T/H to acquire an input signal
is a function of how quickly its input capacitance is
charged. If the input signal’s source impedance is high,
MAX1248/MAX1249
+2.7V to +5.25V, Low-Power, 4-Channel,
Serial 10-Bit ADCs in QSOP-16the acquisition time lengthens, and more time must be
allowed between conversions. The acquisition time,
tACQ, is the maximum time the device takes to acquire
the signal, and is also the minimum time needed for the
signal to be acquired. It is calculated by:
tACQ= 7.6 x (RS+ RIN) x 16pF
where RIN= 9kΩ, RS= the source impedance of the
input signal, and tACQis never less than 1.5µs. Note
that source impedances below 3kΩdo not significantly
affect the ADC’s AC performance.
Higher source impedances can be used if a 0.01µF
capacitor is connected to the individual analog inputs.
Note that the input capacitor forms an RC filter with the
input source impedance, limiting the ADC’s signal
bandwidth.
Input BandwidthThe ADC’s input tracking circuitry has a 2.25MHz
small-signal bandwidth, so it is possible to digitize
high-speed transient events and measure periodic sig-
nals with bandwidths exceeding the ADC’s sampling
rate by using undersampling techniques. To avoid
high-frequency signals being aliased into the frequency
band of interest, anti-alias filtering is recommended.
Analog Input ProtectionInternal protection diodes, which clamp the analog input
to VDDand AGND, allow the channel input pins to swing
from AGND -0.3V to VDD+ 0.3V without damage.
However, for accurate conversions near full scale, the
inputs must not exceed VDDby more than 50mV or be
lower than AGND by 50mV.
If the analog input exceeds 50mV beyond the sup-
plies, do not forward bias the protection diodes of off
channels over 4mA.
How to Start a ConversionA conversion is started by clocking a control byte into
DIN. With CSlow, each rising edge on SCLK clocks a bit
from DIN into the MAX1248/MAX1249’s internal shift reg-
ister. After CSfalls, the first arriving logic “1” bit defines
the control byte’s MSB. Until this first “start” bit arrives,
any number of logic “0” bits can be clocked into DIN with
no effect. Table 1 shows the control-byte format.
The MAX1248/MAX1249 are compatible with SPI/QSPI
and MICROWIREdevices. For SPI, select the correct
clock polarity and sampling edge in the SPI control reg-
isters: set CPOL = 0 and CPHA = 0. MICROWIRE, SPI,
and QSPI all transmit a byte and receive a byte at the
same time. Using the Typical Operating Circuit,the sim-
Table 1.Control-Byte Format
MAX1248/MAX1249plest software interface requires only three 8-bit transfers
to perform a conversion (one 8-bit transfer to configure
the ADC, and two more 8-bit transfers to clock out the
10-bit conversion result). See Figure 19 for MAX1248/
MAX1249 QSPI connections.
Simple Software InterfaceMake sure the CPU’s serial interface runs in master
mode so the CPU generates the serial clock. Choose a
clock frequency from 100kHz to 2MHz.Set up the control byte for external clock mode and
call it TB1. TB1 should be of the format: 1XXXXX11
binary, where the Xs denote the particular channel
and conversion mode selected.Use a general-purpose I/O line on the CPU to pull low.Transmit TB1 and, simultaneously, receive a byte
and call it RB1. Ignore RB1.Transmit a byte of all zeros ($00 hex) and, simulta-
neously, receive byte RB2.Transmit a byte of all zeros ($00 hex) and, simulta-
neously, receive byte RB3.Pull CShigh.
Figure 5 shows the timing for this sequence. Bytes RB2
and RB3 contain the result of the conversion padded
with one leading zero, two sub-bits, and three trailing
zeros. The total conversion time is a function of the
serial-clock frequency and the amount of idle time
between 8-bit transfers. To avoid excessive T/H droop,
make sure the total conversion time does not exceed
120µs.
Digital OutputIn unipolar input mode, the output is straight binary
(Figure 16). For bipolar inputs, the output is two’s com-
plement (Figure 17). Data is clocked out at the falling
edge of SCLK in MSB-first format.
Clock ModesThe MAX1248/MAX1249 may use either an external
serial clock or the internal clock to perform the succes-
sive-approximation conversion. In both clock modes,
the external clock shifts data in and out of the
MAX1248/MAX1249. The T/H acquires the input signal
as the last three bits of the control byte are clocked into
DIN. Bits PD1 and PD0 of the control byte program the
clock mode. Figures 6–9 show the timing characteristics
common to both modes.
External ClockIn external clock mode, the external clock not only shifts
data in and out, it also drives the analog-to-digital con-
version steps. SSTRB pulses high for one clock period
after the last bit of the control byte. Successive-approxi-
mation bit decisions are made and appear at DOUT on
each of the next 10 SCLK falling edges (Figure 5).
SSTRB and DOUT go into a high-impedance state when
+2.7V to +5.25V, Low-Power, 4-Channel,
Serial 10-Bit ADCs in QSOP-16
Table 2.Channel Selection in Single-Ended Mode (SGL/DDIIFF
= 1)
Table 3.Channel Selection in Differential Mode (SGL/DDIIFF
= 0)
MAX1248/MAX1249
+2.7V to +5.25V, Low-Power, 4-Channel,
Serial 10-Bit ADCs in QSOP-16goes high; after the next CSfalling edge, SSTRB will
output a logic low. Figure 7 shows the SSTRB timing in
external clock mode.
The conversion must complete in some minimum time,
or droop on the sample-and-hold capacitors may
degrade conversion results. Use internal clock mode if
the serial-clock frequency is less than 100kHz, or if
serial-clock interruptions could cause the conversion
interval to exceed 120µs.
Figure 6.Detailed Serial-Interface Timing
MAX1248/MAX1249
+2.7V to +5.25V, Low-Power, 4-Channel,
Serial 10-Bit ADCs in QSOP-16
Internal Clock
In internal clock mode, the MAX1248/MAX1249 gener-
ate their own conversion clocks internally. This frees the
µP from the burden of running the SAR conversion clock
and allows the conversion results to be read back at the
processor’s convenience, at any clock rate from 0MHz
to 2MHz. SSTRB goes low at the start of the conversion
and then goes high when the conversion is complete.
SSTRB is low for a maximum of 7.5µs (SHDN= FLOAT),
during which time SCLK should remain low for best
noise performance.
An internal register stores data when the conversion is
in progress. SCLK clocks the data out of this register at
any time after the conversion is complete. After SSTRB
goes high, the next falling clock edge produces the
MSB of the conversion at DOUT, followed by the
remaining bits in MSB-first format (Figure 8). CSdoes
not need to be held low once a conversion is started.
Pulling CShigh prevents data from being clocked into
the MAX1248/MAX1249 and three-states DOUT, but it
does not adversely affect an internal clock mode con-
version already in progress. When internal clock mode
is selected, SSTRB does not go into a high-impedance
state when CSgoes high.
Figure 9 shows the SSTRB timing in internal clock
mode. In this mode, data can be shifted in and out of
the MAX1248/MAX1249 at clock rates exceeding
2.0MHz if the minimum acquisition time, tACQ, is kept
above 1.5µs.
Figure 7.External Clock Mode SSTRBDetailed Timing
