M74HCT74RM13TR ,DUAL D TYPE FLIP FLOP WITH PRESET AND CLEARAbsolute Maximum Ratings are those values beyond which damage to the device may occur. Functional o ..
M74HCT86B1R ,QUAD EXCLUSIVE OR GATEAbsolute Maximum Ratings are those values beyond which damage to the device may occur. Functional o ..
M74HCT86M1R ,QUAD EXCLUSIVE OR GATEM74HCT86QUAD EXCLUSIVE OR GATE ■ HIGH SPEED:t = 15ns (TYP.) at V = 4.5VPD CC■ LOW POWER DISSIPATIO ..
M74HCT86RM13TR ,QUAD EXCLUSIVE OR GATEABSOLUTE MAXIMUM RATINGS Symbol Parameter Value UnitV Supply Voltage-0.5 to +7 VCCV DC Input V ..
M74HCU04 ,HEX INVERTER (SINGLE STAGE)M74HCU04HEX INVERTER (SINGLE STATE) ■ HIGH SPEED:t = 5ns (TYP.) at V = 6VPD CC■ LOW POWER DISSIPAT ..
M74HCU04 ,HEX INVERTER (SINGLE STAGE)Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional o ..
MAX153EAP ,1Msps, レP-Compatible, 8-Bit ADC with 1レA Power-DownELECTRICAL CHARACTERISTICS
(VDD = +5V 16%. GND = 0V; Unipolar Input Range: Vss = GND, VREF+ = 5V ..
MAX153EAP ,1Msps, レP-Compatible, 8-Bit ADC with 1レA Power-DownFeatures
. 660ns Conversion Time
. Power-Up/Power-Down in 200ns
. Internal Track/Hold
. 1 ..
MAX153EAP ,1Msps, レP-Compatible, 8-Bit ADC with 1レA Power-Down19-4740: Rev l; 10/93
MAX153EAP ,1Msps, レP-Compatible, 8-Bit ADC with 1レA Power-DownFeatures
. 660ns Conversion Time
. Power-Up/Power-Down in 200ns
. Internal Track/Hold
. 1 ..
MAX153EAP ,1Msps, レP-Compatible, 8-Bit ADC with 1レA Power-DownApplications
Cellular Telephones
Portable Radios
Battery-Powered Systems
Burst-Mode Data Acqu ..
MAX153EAP+ ,1Msps, µP Compatible, 8-Bit ADC with 1µA Power DownElectrical Characteristics(V = +5V ±5%, V = 0V; Unipolar Input Range: V = GND, V = 5V, V = GND; Bip ..
M74HCT74B1R-M74HCT74M1R-M74HCT74RM13TR
DUAL D TYPE FLIP FLOP WITH PRESET AND CLEAR
1/10August 2001 HIGH SPEED :
fMAX = 48MHz (TYP.) at VCC = 4.5V LOW POWER DISSIPATION:
ICC =2μA(MAX.) at TA=25°C COMPATIBLE WITH TTL OUTPUTS :
VIH = 2V (MIN.) VIL = 0.8V (MAX) BALANCED PROPAGATION DELAYS:
tPLH ≅ tPHL SYMMETRICAL OUTPUT IMPEDANCE:
|IOH| = IOL = 4mA (MIN) PIN AND FUNCTION COMPATIBLE WITH
74 SERIES 74
DESCRIPTIONThe M74HCT74 is an high speed CMOS DUAL D
TYPE FLIP FLOP WITH CLEAR fabricated with
silicon gate C2 MOS technology.
A signal on the D INPUT (nD) is transferred on the
Q OUTPUT during the positive going transition of
the clock pulse. CLEAR (CLR) and PRESET (PR)
are independent of the clock and accomplished by
a low on the appropriate input.
The M74HCT74 is designed to directly interface
HSC2 MOS systems with TTL and NMOS
components.
All inputs are equipped with protection circuits
against static discharge and transient excess
voltage.
M74HCT74DUAL D TYPE FLIP FLOP WITH PRESET AND CLEAR
PIN CONNECTION AND IEC LOGIC SYMBOLS
ORDER CODES
M74HCT742/10
INPUT AND OUTPUT EQUIVALENT CIRCUIT PIN DESCRIPTION
TRUTH TABLE X : Don’t Care
LOGIC DIAGRAM This logic diagram has not be used to estimate propagation delays
M74HCT743/10
ABSOLUTE MAXIMUM RATINGS Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is
not implied
(*) 500mW at 65 °C; derate to 300mW by 10mW/°C from 65°C to 85°C
RECOMMENDED OPERATING CONDITIONS
DC SPECIFICATIONS
M74HCT744/10
AC ELECTRICAL CHARACTERISTICS (CL = 50 pF, Input tr = tf = 6ns)
CAPACITIVE CHARACTERISTICS 1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without
load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC/2 (per FLIP/
FLOP)
M74HCT745/10
TEST CIRCUIT CL = 50pF or equivalent (includes jig and probe capacitance)
RT = ZOUT of pulse generator (typically 50Ω)
WAVEFORM 1 : PROPAGATION DELAY, MINIMUM SETUP AND HOLD TIME, CK MINIMUM PULSE
WIDTH AND MAXIMUM FREQUENCY (f=1MHz; 50% duty cycle)
M74HCT746/10
WAVEFORM 2 : MINIMUM PULSE WIDTH, PROPAGATION DELAY (f=1MHz; 50% duty cycle)
WAVEFORM 3 : MINIMUM PULSE WIDTH AND REMOVAL TIME (f=1MHz; 50% duty cycle)
