M74HCT574M1R ,OCTAL D-TYPE FLIP-FLOP WITH 3-STATE OUTPUT (NON INVERTING)M74HCT574OCTAL D-TYPE FLIP FLOPWITH 3 STATE OUTPUT NON INVERTING ■ HIGH SPEED: ..
M74HCT574RM13TR ,OCTAL D-TYPE FLIP-FLOP WITH 3-STATE OUTPUT (NON INVERTING)Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional o ..
M74HCT574TTR ,OCTAL D-TYPE FLIP-FLOP WITH 3-STATE OUTPUT (NON INVERTING)ABSOLUTE MAXIMUM RATINGS Symbol Parameter Value UnitV Supply Voltage-0.5 to +7 VCCV DC Input V ..
M74HCT640M1R ,OCTAL BUS TRANSCEIVER (3-STATE INVERTING(M74HCT640OCTAL BUS TRANSCEIVERWITH 3 STATE OUTPUTS (INVERTED) ■ HIGH SPEED: t = 13ns (TYP.) at V = ..
M74HCT643B1R ,OCTALE BUS TRANSCEIVER (3-STATE)M74HCT643OCTAL BUS TRANSCEIVERWITH 3 STATE OUTPUTS (INVERTED/NON INVERTED) ■ HIGH SPEED: t = 13ns ..
M74HCT646B1R ,OCTAL BUS TRANSCEIVER/REGISTER (3-STATE)M74HCT646OCTAL BUS TRANSCEIVER/REGISTERWITH 3 STATE OUTPUTS ■ HIGH SPEED: ..
MAX1532ETL , PLASTIC ENCAPSULATED DEVICES
MAX1533AETJ , High-Efficiency, 5x Output, Main Power-Supply Controllers for Notebook Computers
MAX1533AETJ+ ,High-Efficiency, 5x Output, Main Power-Supply Controllers for Notebook ComputersApplicationsON3 2 23 LDO52 to 4 Li+ Cells Battery-Powered DevicesFSEL 3 22 DL5Notebook and Subnoteb ..
MAX1533ETJ+T ,High-Efficiency, 5x Output, Main Power-Supply Controllers for Notebook ComputersApplicationsON3 2 23LDO52 to 4 Li+ Cells Battery-Powered DevicesFSEL 3 22 DL5Notebook and Subnotebo ..
MAX1534ETE+T ,High-Efficiency, Triple-Output, Keep-Alive Power Supply for Notebook ComputersFeaturesThe MAX1534 is a high-efficiency, triple-output power♦ One Switching and Two Linear Regulat ..
MAX1535AETJ ,Highly Integrated Level 2 SMBus Battery ChargerApplicationsLDO 2 23 DLONotebook and Subnotebook ComputersACIN 3 22 PGNDTablet PCsREF 4 21 CSIPMAX1 ..
M74HCT574M1R-M74HCT574RM13TR-M74HCT574TTR
OCTAL D-TYPE FLIP-FLOP WITH 3-STATE OUTPUT (NON INVERTING)
1/11August 2001 HIGH SPEED:
fMAX = 50MHz (TYP.) at VCC = 4.5V LOW POWER DISSIPATION:CC = 4μA(MAX.) at TA =25°C COMPATIBLE WITH TTL OUTPUTS : IH = 2V (MIN.) VIL = 0.8V (MAX) SYMMETRICAL OUTPUT IMPEDANCE:
|IOH| = IOL = 6mA (MIN) BALANCED PROPAGATION DELAYS:
tPLH ≅ tPHL PIN AND FUNCTION COMPATIBLE WITH
74 SERIES 574
DESCRIPTIONThe M74HCT574 is an high speed CMOS OCTAL
D-TYPE FLIP FLOP WITH 3-STATE OUTPUTS
INVERTING fabricated with sub-micron silicon
gate C2 MOS technology.
This 8 bit D-TYPE FLIP FLOP is controlled by a
clock input (CK) and an output enable input (OE).
On the positive transition of the clock, the Q
outputs will be set to the logic state that were
setup at the D inputs.
While the OE input is at low level, the eight outputs
will be in a normal logic state (high or low logic
level) and while OE is in high level the outputs will
be in a high impedance state.
The output control does not affect the internal
operation of flip-flops; that is, the old data can be
retained or the new data can be entered even
while the outputs are off.
All inputs are equipped with protection circuits
against static discharge and transient excess
voltage.
M74HCT574OCTAL D-TYPE FLIP FLOP
WITH 3 STATE OUTPUT NON INVERTING
PIN CONNECTION AND IEC LOGIC SYMBOLS
ORDER CODES
M74HCT5742/11
INPUT AND OUTPUT EQUIVALENT CIRCUIT PIN DESCRIPTION
TRUTH TABLE X: Don’t Care
Z: High Impedance
LOGIC DIAGRAM This logic diagram has not be used to estimate propagation delays
M74HCT5743/11
ABSOLUTE MAXIMUM RATINGS Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is
not implied
(*) 500mW at 65 °C; derate to 300mW by 10mW/°C from 65°C to 85°C
RECOMMENDED OPERATING CONDITIONS
M74HCT5744/11
DC SPECIFICATIONS
M74HCT5745/11
AC ELECTRICAL CHARACTERISTICS (CL = 50 pF, Input tr = tf = 6ns)
CAPACITIVE CHARACTERISTICS 1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without
load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC/8 (per
Flip-Flop)
M74HCT5746/11
TEST CIRCUIT CL = 50pF/150pF or equivalent (includes jig and probe capacitance)
R1 = 1KΩ or equivalent
RT = ZOUT of pulse generator (typically 50Ω)
WAVEFORM 1: CK TO Qn PROPAGATION DELAYS, CK MAXIMUM FREQUENCY, Dn TO CK
SETUP AND HOLD TIMES (f=1MHz; 50% duty cycle)
