M74HCT4053M1R ,TRIPLE 2-CHANNEL ANALOG MULTIPLEXER/DEMULTIPLEXERM74HCT4053TRIPLE 2-CHANNELANALOG MULTIPLEXER/DEMULTIPLEXER ■ LOW POWER DISSIPATION:I = 4μA (MAX.) ..
M74HCT540 ,HCT540: INVERTEDM74HCT540OCTAL BUS BUFFERWITH 3 STATE OUTPUTS (INVERTED) ■ HIGH SPEED:t = 12ns (TYP.) at V = 4.5VP ..
M74HCT540M1R ,OCTAL BUS BUFFER WITH 3 STATE OUTPUTS (INVERTED)Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional o ..
M74HCT540RM13TR ,OCTAL BUS BUFFER WITH 3 STATE OUTPUTS (INVERTED)M74HCT540OCTAL BUS BUFFERWITH 3 STATE OUTPUTS (INVERTED) ■ HIGH SPEED:t = 12ns (TYP.) at V = 4.5VP ..
M74HCT541M1R ,OCTAL BUS BUFFER WITH WITH 3 STATE OUTPUTS (NON INVERTED)ABSOLUTE MAXIMUM RATINGS Symbol Parameter ValueUnitV Supply Voltage-0.5 to +7 VCCV DC Input Vo ..
M74HCT541M1R ,OCTAL BUS BUFFER WITH WITH 3 STATE OUTPUTS (NON INVERTED)M74HCT541OCTAL BUS BUFFERWITH 3 STATE OUTPUTS (NON INVERTED) ■ HIGH SPEED:t = 14ns (TYP.) at V = 4 ..
MAX1522EUT+T ,Simple SOT23 Boost Controllersapplications where♦ Low Quiescent Current (25µA typ)extremely low cost and small size are top prior ..
MAX1522EUT-T ,Simple SOT23 Boost Controllersapplications.
M74HCT4053M1R
TRIPLE 2-CHANNEL ANALOG MULTIPLEXER/DEMULTIPLEXER
1/12September 2001 LOW POWER DISSIPATION:
ICC = 4μA (MAX.) at TA=25°C LOGIC LEVEL TRANSLATION TO ENABLE
TTL LOGIC SIGNAL TO COMMUNICATE
WITH ±5V ANALOG SIGNAL LOW "ON" RESISTANCE:
70Ω TYP. (VCC - VEE = 4.5V)
50Ω TYP. (VCC - VEE = 9V) WIDE ANALOG INPUT VOLTAGE RANGE:
±6V FAST SWITCHING:pd = 13ns (TYP.) at TA = 25 °C LOW CROSSTALK BETWEEN SWITCHES HIGH ON/OFF OUTPUT VOLTAGE RATIO WIDE OPERATING SUPPLY VOLTAGE
RANGE (VCC - VEE) = 2V TO 12V LOW SINE WAVE DISTORTION:
0.02% at VCC - VEE = 9V COMPATIBLE WITH TTL OUTPUTS:IH = 2V(MIN.) VIL = 0.8V (MAX.) PIN AND FUNCTION COMPATIBLE WITH
74 SERIES 4053
DESCRIPTIONThe M74HCT4053 is a triple two-channel analog
MULTIPLEXER/DEMULTIPLEXER fabricated
with silicon gate C2 MOS technology and it is pin
to pin compatible with the equivalent metal gate
CMOS4000B series.
It contains 6 bidirectional and digitally controlled
analog switches.
A built-in level shifting is included to allow an input
range up to ±6V (peak) for an analog signal with
digital control signal of 0 to 6V.EE supply pin is provided for analog input
signals. It has an inhibit (INH) input terminal to
disable all the switches when high, compatible
with TTL output level. For operation as a digital
multiplexer/demultiplexer, VEE is connected to
GND. A, B and C control inputs select one of a pair
of channels, they are compatible with TTL output
level.
All inputs are equipped with protection circuits
against static discharge and transient excess
voltage.
M74HCT4053TRIPLE 2-CHANNEL
ANALOG MULTIPLEXER/DEMULTIPLEXER
PIN CONNECTION AND IEC LOGIC SYMBOLS
ORDER CODES
M74HCT40532/12
CONTROL INPUT EQUIVALENT CIRCUIT
I/O EQUIVALENT CIRCUIT
PIN DESCRIPTION
TRUTH TABLE
FUNCTIONAL DIAGRAM
M74HCT40533/12
ABSOLUTE MAXIMUM RATINGS Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is
not implied
(*) 500mW at 65 °C; derate to 300mW by 10mW/°C from 65°C to 85°C
RECOMMENDED OPERATING CONDITIONS
M74HCT40534/12
DC SPECIFICATIONS
M74HCT40535/12
AC ELECTRICAL CHARACTERISTICS (CL = 50 pF, Input tr = tf = 6ns)
CAPACITANCE CHARACTERISTICS 1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without
load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC
M74HCT40536/12
ANALOG SWITCH CHARACTERISTICS (GND = 0V;TA = 25°C)
(*) Input COMMON Terminal, and measured at SWITCH Terminal
(**) Input SWITCH Terminal, and measured at common Terminal
NOTE: These characteristics are determined by the design of the device.
